EXP-2000 User manual SPX Expansion interface modules The EXP-2000 provides additional Door/Panel interface points to most SPX products. The EXP-2000 uses a local RS-485 network through an SPX gateway device. Additional access points can be added as needed.
1 Electrical and Mechanical Specifications Physical Temp Humidity Aluminum Enclosure 3.5" x 2.75" x .75" each unit Storage(-55˚C to + 150˚C) Operating(-40˚C to +80˚C) 95% (non-condensing) Input Unreg Input 8 to 16 VDC* @ 200mA Max Output +5VDC @100mA Power Data I/O Interface Reader 0- 30VDC LED - 0 - 30VDC Analog 0 - 5 VDC * See Rating Curve for Temperature and Power ratings 3.3” ø 0.15” 2.8” DataBender CVX-1300 1.4” Unit Height = 0.75” 3.
1 EXP-2000 Operation The EXP-2000 can be utilized as an additional door and panel interface pair (Remote and Central) with an existing Suprex® SPX-7400, SPX-7500. SPX-5600, or SPX-7200 system. Each EXP-2000 can be set to a unique address (1 through 15, see DIP switch chart). EXP Units used with a Cypress Suprex Gateway device will be set to the same address on both the Central and Remote sides of the system.
1 EXP-2000 C Electrical Connections J1 2- 8 to 16 VDC In 1- Ground J2 8-RS485 (+) 7-RS485 (-) 6-+5 VDC Out 5-prog res 2 4-prog res 1 3-LED In 2-Data 1 out 1-Data 0 out J3 J3 Connections Power IN (+) Power IN (-) J2 Connections 8 - RS485 (+)!! 7 - RS485 (-)! ! 6 - +5 VDC OUT! 5 - Analog 2! ! 4 - Analog 1 ! ! 3 - LED I/O! ! 2 - Data 1 Out! 1 - Data 0 Out! EXP-2000 C * J1 Connections 2 - 8 to 16 VDC ! 1 - Ground! ! . 12-R4 N.O. 11-R4 Com 10-R4 N.C 9-R3 N.O. 8-R3 Com 7-R3 N.C.
1 EXP-2000 R Electrical Connections J1 2- 8 to 16 VDC In 1- Ground J2 8-RS485 (+) 7-RS485 (-) 6-+5 VDC Out 5- R4 in 4- R3 in 3-LED out 2-Data 1 in 1-Data 0 in EXP-2000 R * J1 Connections 2 - 8 to 16 VDC ! 1 - Ground! ! Power IN (+) Power IN (-) 12 - Relay #2!! 11 - Relay #2!! 10 - Relay #2!! 9 - Relay #1! ! 8 - Relay #1! ! 7 - Relay #1! ! 6 - RS232 Output ! 5 - RS232 Input ! 4 - Ground! ! 3 - Aux in! ! 2 -! ! ! 1- ! ! ! RS-485 Input RS-485 Input 5 Volt Power out Analog Input #4 Analog Input #3 LE
1 Electrical and Environmental Specifications 80 55 Ambient Temperature (Degrees Celsius) 35 -40 8 10 12 14 16 Supply Voltage Temperature/Voltage de-rating curve The EXP-1000 units should be operated with a filtered 12 Volt nominal DC supply. Any voltage between 8 and 16 volts can be utilized by following the temperature /voltage derating curve. Voltage should not exceed 16 VDC under normal operating conditions.
1 SPX to EXP-2000 Connections 8- EXP(+) 7- EXP(-) 6- +5VDC Out 5- Analog IN2 4- Analog IN1 3- LED I/O 2- D1 I/O 1- D0 I/O SPX CYPRESS 8-RS485 (+) 7-RS485 (-) 6-+5 VDC Out 5-Analog 2 4-Analog 1 3-LED I/O 2-Data 1 I/O 1-Data 0 I/O EXP-2000 * CYPRESS 8-RS485 (+) 7-RS485 (-) 6-+5 VDC Out 5-Analog 2 4-Analog 1 3-LED I/O 2-Data 1 I/O 1-Data 0 I/O * Page 7 of 7 EXP-2000
