P O R T A B L E INDOOR / OUTDOOR AIR COOLER OWNER’S INSTRUCTION MANUAL SI5000 SI4000 C O O L A I R A N Y W H E R E ! by
1 1 PORTABLE INDOOR / OUTDOOR EVAPORATIVE AIR COOLER IMPORTANT SAFETY INSTRUCTIONS Please read these instructions before assembling the cooler and keep for future reference. SI4000 SI5000 Waste electrical products must not be disposed of with household waste. This product should be taken to your local recycling centre for safe treatment. As the policy of this company is one of continuous improvement, all specifications are subject to change without notice.
2 INTRODUCTION CONTENTS KEY 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. SAFETY INSTRUCTIONS.........................3 OPERATING INSTRUCTIONS...............4-6 Filling the water tank Draining the water tank Cooler location Using the Control Panel Using the Remote Panel MAINTENANCE......................................6-8 Regular Maintenance General cleaning Cleaning the water tank Cleaning the cooling pads TECHNICAL SPECIFICATIONS................
3 SAFETY INSTRUCTIONS WARNING: This cooler is intended for use in an indoor or outdoor, domestic, office or warehouse environment only. Any other use is not recommended by the manufacturer and may cause fire, electrical shocks or other injury to person or property. When using electrical appliances, basic safety precautions should always be followed: Your cooler operates on 220-240 Volt AC, 50Hz current only. Check the voltage to ensure it matches the cooler’s rated specification.
4 OPERATING INSTRUCTIONS FILLING THE WATER TANK DRAINING THE WATER TANK Warning: Turn the power off, unplug and move the cooler into position prior to filling or draining the water tank. Warning: Turn off and unplug the cooler prior to moving, servicing, filling or draining the water tank. Fill the water tank with clean water. To do this, open the water fill door located on the side panel (Fig. 1). The tank is full when the water level indicator reaches the ‘MAX’ position.
1 5 OPERATING INSTRUCTIONS Warning: Do not operate the cooler with the cooling pads or grilles removed. Plug the cooler in to a power outlet. The cooler will be in stand-by mode (the cooler will beep and the amber coloured POWER symbol will be lit), ready for operation. Note! Maximum cooling will not be achieved until the wetting media is fully saturated. This may take several minutes. USING THE CONTROL PANEL The cooler’s control panel has a ‘touch’ sensitive panel.
6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS (cont) Timer Your cooler is fitted with a timer to automatically turn off up to 8 hours in advance. Touch the TIMER button to set the timer. The TIMER can be set from 0.5 to 8.0 hours in 0.5 hour increments. Each touch will increase the set time by 0.5 hours. To cancel the TIMER, continue touching until the display value reads “0.0”. Alternatively, turn the POWER off and back on again.
1 7 MAINTENANCE CLEANING AND MAINTENANCE Warning: Always disconnect the cooler from the electricity mains power before moving, cleaning or any maintenance. Regular Maintenance: Regular maintenance will maximize the efficiency and service life from your cooler. Before starting any maintenance operation, read thoroughly all operating and maintenance instructions observing all cautions and warning.
8 MAINTENANCE Once the pad frame is free, gently bend the tabs on each side to release the water spreader pan (Fig.10). Once the water spreader pan is removed, the cooling pad can slide out of the assembly for cleaning (Fig.11). Front Pad Assembly: Remove the four screws retaining the front panel (Fig.7). Remove the front panel assembly by lifting the bottom side and unhooking the tabs on top. To remove the pad follow the same instructions as the rear pad assembly.
1 9 TROUBLESHOOTING CONDITION POSSIBLE CAUSE REMEDY Cooler will not operate initially. Cord is not plugged in. Ensure cord is plugged in and switched on at power outlet. Power outlet or supply faulty. Check the power outlet. Check the power supply Incorrect voltage. Check that the power supply is the same as specified on the rating label. Pump is not turned on. Turn cool mode on by pressing the COOL button. Water tank is low or empty.
NOTES 10
It is the policy of Seeley International to introduce continual product improvement. Accordingly, specifications are subject to change without notice. Please consult with your dealer to confirm the specifications of the model selected. Service Australia 1-300-650-644 seeleyinternational.com 133003-E 00300901-B seeleyinternational.