5 inch SVGA LCD Monitor ID#15001 Operation Manual
Introduction This is a 15 inch LCD SVGA input monitor for arcade machines and CNC machinery retrofits. It features the VESA plug & play system which allows the monitor to automatically adjust itself to the match the frequency of the user's device. Features • • • • • High brightness. Fast response time. Power saver. Low electromagnetic wave and power saver. Safety certifications. • • The power control system is installed inside the LCD monitor.
Setting up your LCD monitor Screen Adjustment To enter adjust mode, please refer to the OSD control. • • • • • • • • • • • • Turn the computer and LCD monitor on. Press “Auto” button to start auto adjust. This will start the auto adjust process. This will take approximately 10 seconds. You may notice the image changing and occasionally flashing (this is normal). Your LCD monitor provides a self testing function, through which you can check whether the LCD monitor functions are working properly.
Panel Controls Adjusting the 1. LED Green : Power On + Signal Source Detected Red : Standby or Signal Source Not Detected Off : Power off Power On/Off. 2. Power 3. Up/+ This button is used for positive adjustment when OSD is Displayed 4. Down/- 5. Menu 6. Auto This button is used for negative adjustment when OSD is Displayed This button is used to display the ON Screen Display (OSD) menu and select settings and parameters.
Image • • • • • • • Press the menu button to start the OSD feature. Click the “Up” or “Down” button to select the function to be adjusted. Click the “Menu” button to access into the function to be adjusted. Click the “Up” or “Down” button to change the current setting of the function selected. To exit the OSD menu or go back to a previous menu click the “Auto/Esc” button. Upon exiting the menu any changes will be automatically saved.
OSD Menu Options Menu Auto Setup Brightness Automatically optimize positions, phase and clock Brightness Adjust Screen Brightness Recall Restore to Default Return Exit menu Contrast Adjust the Screen Contrast Display Adjust H Position Adjust the Horizontal Positioning V Position Adjust the Vertical Positioning V Size Adjust the Vertical Screen Size Clock Adjusts horizontal alignment Phase Adjusts horizontal alignment Quality Adjusts the quality of the image Mode Selection Default Anal
OSD Display VGA/DVI Audio OSD H-Pos Position the OSD menu horizontally on screen OSD V-Pos Position the OSD menu vertically on screen OSD Timer Set the OSD menu on screen display time OSD Transparency Set the OSD menu Transparency OSD Direction Set the direction of the OSD menu : Normal, Mirror, Left, Right, Up or Down Display Logo Display Logo Recall Restore to Default Return Exit Menu Analog Input Selects VGA input Digital Input Unavailable Return Exit Menu Audio Mute Audio Volu
Support CGA/EGA/VGA Timings Type H. Frequency. V. Frequency Resolution (kHz) (Hz) CGA 15.4 58.8 640x198 CGA 15.1 57.6 640x215 CGA 15.7 60 640x215 CGA 16.0 61 640x215 CGA 16.3 62 640x215 CGA 16.6 63.4 640x215 CGA 16.800 64 640x215 CGA 15.6 50.3 640x265 CGA 18.4 50 640x350 VGA 31.469 70.087 640x400 VGA 31.469 59.940 640x480 VGA 35.000 66.667 640x480 VGA 37.861 72.809 640x480 VGA 37.500 75.000 640x480 SVGA 35.156 56.250 800x600 SVGA 37.879 60.317 800x600 SVGA 48.077 72.188 800x600 SVGA 46.875 75.
Connecting into Monitor Option 1 - Using VGA Input By using a standard VGA 15 pin computer cable plug and play or, alternatively you may cut the end of your cable and wire directly to the output connector of the source equipment. Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Analog red input. Analog green input. Analog blue input. Ground. Digital ground. Analog red ground. Analog green ground. Analog blue ground. Ground. Sync ground. Ground.
P1 – RGBHV separate/ or combined sync P3 – RGBH+V combined sync Pin 1 – Red Pin 1 – Red Pin 2 – Green Pin 2 – Green Pin 3 – Blue Pin 3 – Blue Pin 4 – Signal Earth Pin 4 – Signal Earth Pin 5 – Horizontal/Combined Sync Pin 5 – Horizontal/Combined Sync Pin 6 – Vertical Sync About Our Adapter PCB and Further Adjustments Our adapter PCB offers a number of adjustments via the following controls -VR1 to VR3 Adjust to vary the level of the individual output colour signals to compensate for over exposur
Filter Jumpers Set Jumpers as required to reduce effect of black line artifacts when low resolution mismatch becomes evident on LCD screen. By setting to “ON” position, each colour can be filtered as required. .
Specifications Specifications for this Model Screen Size 15" TFT Pixel Pitch(mm) 0.264 x 0.264 Blacklight 2xCCFL Cell Type TN Input Mode SVGA Scan Frequency Horizontal 15 ~ 80KHZ Scan Frequency Vertical 48 ~ 75Hz Colours 16.7M Colors Aspect Ratio 5:4 Horizontal Viewing Angle Full range Optimal Screen Resolution 1024 x 768 Bandwidth 130MHz Dot Clock Contrast Ratio 500:1 Typ Brightness 250cd/m2 Power 100~240V 50/60Hz via 12VDC 1.2A adapter Power Consumption 13.35 Watts(Typ.
Troubleshooting Error Solution No Power Led Check Mains Power supply input Voltage (100v or 240vAC) and connection Check 12V DC at power supply output Check control board for damage No image Check cables connected correctly from source and into monitor inputs Check correct orientation of signal wires; H-sync and V-sync Check for CCFL lamp operation on rear of lcd panel, visual reference only Check power 'on' source and monitor Image Alignment Adjust using “AUTO” button Fine adjust using the OSD Menu
