HDBaseT 4x4 HDMI Matrix over CAT5e/6/7 Cable - ID# 15121 Operation Manual
Introduction The 4x4 HDMI Matrix over 4 CAT5e/6/7 with 2 HDMI outputs supports resolutions up to 1080p Full HD and 1920x1200@60Hz with multichannel digital audio from up to four high definition sources to up to four CAT5e/6/7 output and 2 HDMI synchronized with 2 CAT5e/6/7 output ports. It supports digital audio formats such as LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio. Also, 3D content can be displayed when connecting a 3DTV and 3D source.
Operation Controls and Functions Front Panel 1. LCM: This monitor displays your setting information with each input and output selection. 2. IR: This IR window accepts the remote control signal of this device only. 3. Power button LED: Press this button to turn on the device and the green LED will illuminate when the power is on. When the LED illuminate in red it is in standby mode 4. LOCK: Press this button to lock all the buttons on the panel and the LED will illuminate. To unlock, just press it again.
Back Panel 1. RS-232: This slot is to connect with D-Sub 9pin cable from the PC/ NB device for RS-232 control. 2. IP CONTROL: This port is also the link for Telnet system. For non Ethernet version this port is the link for Telnet control, connect to an active Ethernet link with an RJ45 terminated cable (for details, please refer to section RS-232 & Telnet commands). Warning: Please do not connect this port directly to the PC/Laptop as the Telnet function will not work 3.
11. DC24V: This slot is to plug the power cord with adaptor included in the package and then connect them with AC wall outlet for power supply. Side Panel 1. Ventilator: These are fan ventilator area, DO NOT block these area or cover it with any object. Remote Control 1. Power: Press this button to switch on the device or set it to standby mode. 2. IN: Input ports selection 1~4. 3. OUT: Output ports selection A~D.
RS-232 Protocols #ID 15120 Remote Control Console PIN Assignment PIN Assignment 1 NC 1 NC 2 Tx 2 Rx 3 Rx 3 Tx 4 NC ► 4 NC 5 GND ◄ 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Baud Rate: 19200bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1 RS-232 & Telnet Commands Command Description A1~A4 Switch output A to 1~4 B1~B4 Switch output B to 1~4 C1~C4 Switch output C to 1~4 D1~D4 Switch output D to 1~4 AB... 1~CD...4 Switch output ABCD...
Note: All the commands will not be executed unless followed with a carriage return. All letters are case-insensitive. Telnet Control Before attempting to use the telnet control, please ensure that both the Matrix (via the 'LAN /CONTROL' port) and the PC/Laptop are connected to the active networks. To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd" in the Search field then press enter.
Type “IPCONFIG” To show all IP configurations. To reset the IP, type “RSTIP” and to use a set static IP, type ”SETIP” (For a full list of commands, see the RS-232 & Telnet Commands above). Note: Any commands will not be executed unless followed by a carriage return. Commands are case-insensitive.
Clicking on the 'User Setting' tab allows you to reset the IP configuration. The system will ask for a reboot of the device every time any of the settings are changed. The IP address needed to access the Web GUI control will also need to be changed accordingly on the web address entry bar.
Connection Diagram
Specifications Video Bandwidth Input Ports Output Ports Power Supply ESD Protection 225 MHz/6.75 Gbps 4 x HDMI, 5 x IR Extender, 1 x Control 1 x RS-232, 1 x Mini USB B type(for firmware update only) 4 x CAT5e/6/7, 2 x HDMI, 5 x IR Blaster 24V/2.