Installation Guide

ManualsBrandsCoolaroo ManualsWindow ShadesBrown Light Filtering Cordless High-Density Polyethylene Exterior Shade (Common: 72-in x 72-in; Actual: 72-in x 72-in)

Congratulations on the purchase of your Coolaroo® Simple Lift™ Outdoor Roller Shade. Whether you choose to install it in your apartment or

home on a window, balcony, patio, porch or deck, simply follow the directions included here to create a safer, more enjoyable environment

with increased privacy.

Please take a moment to review the parts list before beginning the steps below. Your Simple Lift™ Outdoor Roller Shade can either be hung

from the top of a surface i.e. window frame, (Fig. 1) or side mounted on the inside surface of a wall, patio or porch. Regardless of how you

choose to install the shade, the installation instructions remain the same.

INSTALL THE MOUNTING BRACKETS

A. Using the mounting bracket as your guide, mark the holes

where the screws will go with a pencil. The tension wheel

component will need to be installed on the right hand side.

Note: Be sure the mounting brackets on both ends

are level and in line with each other.

B. Use a 3/32” drill bit to pre-drill the holes. If you are mounting

the shade on a material other than wood, use the optional wall

anchors which can be inserted into the pre-drilled holes.

C. Install the mounting brackets to the top of a surface or inside of

the surface area using the wood screws provided. (Fig. 1)

INSTALL THE SHADE

A. Position the shade so that the tension wheel component is on

the right. (Fig. 2)

Note: You will also want to position the head rail so

that the red tension brake is facing you. This will make

it easier for you to remove the brake as described in

step E.

PARTS LIST QTY

1 Head rail 1

2 Mounting brackets 2

3 Tension wheel component 1

4 Idle end 1

5 Shade 1

6 Bottom rail 1

7 Bottom rail cap 2

8 Wood screws 4

9 Drywall anchors 4

20 minute set up

(approximate time)

Fig.1

Fig.2

(1) Head rail

(3) Tension wheel

component

(4) Idle end

(5) Shade

(6) Bottom rail

(7) Bottom

rail cap

(8) Wood

screws

(9) Drywall

anchors

(2) Mounting

brackets

Additional tensioning

may be required

Screwdriver

Measuring tape

Pencil

Drill with 3/32” drill bit

ADDITIONAL

TOOLS

NEEDED

WARNING

Outdoor Roller Shade

Simple Li

INSTRUCTION MANUAL

Summary of content (6 pages)

PAGE 1
Outdoor Roller Shade Simple LiftTM INSTRUCTION MANUAL Congratulations on the purchase of your Coolaroo® Simple Lift™ Outdoor Roller Shade. Whether you choose to install it in your apartment or home on a window, balcony, patio, porch or deck, simply follow the directions included here to create a safer, more enjoyable environment with increased privacy.
PAGE 2
B. C. D. E. 3 Insert the right side of the roller shade first. (Fig. 3) Install the left side of the shade by sliding the idle end into the mounting bracket. (Fig. 4) Once the roller shade is installed, remove the tape from the tension wheel component. (Fig. 5) Pull down the shade until the red tensioning brake is completely removed. (Fig. 6) Fig.3 RAISING AND LOWERING THE SHADE Having successfully followed the steps above, your shade should be in the retracted position (rolled up) and ready to use.
PAGE 3
Store à enroulement automatique d’extérieur Simple LiftTM MANUEL D’UTILISATION Félicitations pour l’achat de votre store à enroulement automatique d’extérieur Coolaroo® Simple Lift™. Que vous choisissiez de l’installer sur la fenêtre, le balcon, le porche ou la terrasse de votre appartement ou de votre maison, suivez simplement les instructions ci-incluses pour créer un environnement plus sûr, plus agréable et plus intime.
PAGE 4
B. C. D. E. 3 Insérez d’abord le côté droit du store à enroulement automatique . (Fig. 3) Installez le côté gauche du store en glissant le dispositif fixe dans le support de fixation. (Fig. 4) Une fois le store à enroulement automatique installé, retirez le ruban adhésif du composant de roue de tension. (Fig. 5) Abaissez le store jusqu’à ce que le frein de tension rouge soit complètement retiré. (Fig. 6) Fig.
PAGE 5
Persiana en rollo para exteriores Simple LiftTM MANUAL DE INSTRUCCIONES Felicitaciones por la compra de su persiana en rollo para exteriores Coolaroo® Simple Lift™. Ya sea que elija instalarlas en su apartamento o en su hogar en una ventana, en el balcón, el patio, el porche o la terraza, solo siga las instrucciones que se incluyen para crear un ambiente más seguro y que pueda disfrutar más con mayor privacidad.
PAGE 6
B. C. D. E. 3 Inserte primero el lado derecho de la persiana en rollo. (Fig. 3) Instale el lado izquierdo de la persiana al deslizar el extremo inactivo en el soporte de montaje. (Fig. 4) Una vez que la persiana en rollo esté instalada, retire la cinta del componente de la rueda de tensión. (Fig. 5) Jale la persiana hasta retirar por completo el tope de tensión rojo. (Fig. 6) Fig.