Installation Guide

ManualsBrandsCoolaroo ManualsOutdoor ShadesCut-to-Width Brown Cordless Spring Operated Exterior Roller Shade - 72 in. W x72 in. L

Congratulations on the purchase of your Coolaroo® Simple Lift™ Outdoor Roller Shade. Whether you choose to install it in your apartment or home on a

window, balcony, patio, porch or deck, simply follow the directions included here to create a safer, more enjoyable environment with increased privacy.

Your Simple Lift™ Outdoor Roller Shade is fully assembled and only needs to be installed before it can be used. Before beginning the steps below, please

take a moment to review the parts list you will need to hang the shade.

Your Simple Lift™ Outdoor Roller Shade can either be hung from the top of a surface (i.e. window frame, (Fig. 1) or side mounted on the inside surface of a

wall, patio or porch. Regardless of how you choose to install the shade, the installation instructions remain the same.

INSTALL THE MOUNTING BRACKETS

A. Using the mounting bracket as your guide, mark the holes where the

screws will go with a pencil. The tension wheel bracket will need to be

installed on the right hand side.

Note: Be sure the brackets on both ends are level and in

line with each other.

B. Use a 3/16” drill bit to pre-drill the holes. If you are mounting the

shade on a material other than wood The optional wall anchors which

can be inserted into the pre-drilled holes are included.

C. Mount the installation brackets to the ceiling or wall using the wood

screws provided. (Fig. 1)

INSTALL THE SHADE

A. Next, position the shade so that the tension wheel side of the roller

shade is on the right. (Fig. 2)

Note: You will also want to position the head rail (roll) so that

the red tension brake is facing you. This will make it easier for

you to remove the brake as described in Step E.

ADDITIONAL TOOLS

NEEDED

Screwdriver

Measuring tape

Pencil

Drill with 3/16” drill bit

PARTS LIST QTY

1 Head rail 1

2 Mounting brackets 2

3 Tension wheel component 1

4 Idle end 1

5 Shade 1

6 Bottom rail 1

7 Bottom rail cap 2

8 Wood screws 4

9 Drywall anchors 4

20 minute set up

(approximate time)

Fig.1

Fig.2

(1) Head rail

(3) Tension wheel

component

(4) Idle end

(5) Shade

(6) Bottom rail

(7) Bottom

rail cap

(8) Wood

screws

(9) Drywall

anchors

(2) Mounting

brackets

Outdoor Roller Shade

Simple Li

INSTRUCTION MANUAL

Summary of content (6 pages)

PAGE 1
Outdoor Roller Shade Simple LiftTM INSTRUCTION MANUAL Congratulations on the purchase of your Coolaroo® Simple Lift™ Outdoor Roller Shade. Whether you choose to install it in your apartment or home on a window, balcony, patio, porch or deck, simply follow the directions included here to create a safer, more enjoyable environment with increased privacy.
PAGE 2
B. C. D. E. Install the right side of the roller by inserting the tab on the right bracket into tension wheel. (Fig. 3) Install the left side by sliding the idle end into the idle end bracket. (Fig. 4) Once the roller shade is mounted, remove the blue tape from the tension wheel end. (Fig. 5) Gently pull down on shade until red tension wheel break is completely removed from tension wheel. (Fig.
PAGE 3
Store à enroulement d’extérieur Simple LiftTM MANUEL D’INSTRUCTIONS Félicitations pour l’achat de votre store à enroulement d’extérieur Coolaroo® Simple Lift™. Que vous choisissiez de l’installer sur la fenêtre, le balcon, le porche ou la terrasse de votre appartement ou de votre maison, suivez simplement les instructions ci-incluses pour créer un environnement plus sûr, plus agréable et plus intime.
PAGE 4
B. C. D. E. Installez le côté droit du rouleau en insérant la languette du support droit dans la roue de tension. (Fig. 3) Installez le côté gauche en faisant glisser l’extrémité libre dans le dispositif fixe. (Fig. 4) Une fois le store à enroulement installé, retirez le ruban adhésif bleu de l’extrémité de la roue de tension. (Fig. 5) Abaissez doucement le store jusqu’à ce que le frein rouge de la roue de tension soit complètement retiré de la roue de tension. (Fig.
PAGE 5
Outdoor Roller Shade Simple LiftTM MANUAL DE INSTRUCCIONES Felicitaciones por la compra de su persiana en rollo para exteriores Coolaroo® Simple Lift™. Ya sea que elija instalarlas en su apartamento o en su hogar en una ventana, en el balcón, el patio, el porche o la terraza, solo siga las instrucciones que se incluyen para crear un ambiente más seguro y que pueda disfrutar más con mayor privacidad.
PAGE 6
B. C. D. E. Instale el costado derecho del rollo colocando la lengüeta en la abrazadera derecha en la rueda de tensión. (Fig. 3) Instale el costado izquierdo deslizando el extremo inactivo hacia la abrazadera con el extremo inactivo (Fig. 4) Una vez que la persiana en rollo está instalada, retire la cinta azul del extremo de la rueda de tensión. (Fig. 5) Jale la persiana con suavidad hasta que el tope de la rueda de tensión esté completamente retirado de la rueda de tensión. (Fig.