Instructions / Assembly

1 | P a g e

Qty

Item

Description

CoolBot Pro

Patented Digital Temperature Controller

CoolBot Jumper

Wi-Fi Radio Signal Module

Temperature Sensors

Sensor Cables (Blue Cable - Black Tip) with external 2.5mm jack connector

Heater

CoolBot Heater Cable (Black Cable - Red Tip) with external 2.5mm jack connector

Data Cable

Data Transfer Cable (Silver or Grey) with RJ11 connector on both ends

Power Supply

Mini-USB port connector cable. Input: 110V-240V / Output: 5V, 1Amp

BEFORE STARTING

• Should I read this guide? Yes! We highly recommend reading this “Step by Step” guide entirely to ensure proper installation.

We also encourage you to visit our support page www.storeitcold.com/support and read the detailed CoolBot Pro Manual.

• What if I don’t have Internet OR Wi-Fi? No problem! You can still use the CoolBot Pro without the CoolBot Jumper and without

a Wi-Fi connection just like the previous generation CoolBots. Go straight to the “INSTALLING YOUR COOLBOT PRO TO YOUR

A/C” Section of this guide (page 3). NOTE: Your CoolBot Pro will keep your cooler cold but you won’t be able to access data or

change settings from the CoolBot Pro App.

• I have an Internet connection AND Wi-Fi. Awesome! Then you will enjoy all of the benefits the CoolBot Pro and its App. Start

with “CONNECTING YOUR COOLBOT PRO TO YOUR WI-FI NETWORK” Section of this guide (page 2) and then move to the

“INSTALLING YOUR COOLBOT PRO TO YOUR A/C” Section of this guide (page 3).

• I am replacing my existing CoolBot with the new CoolBot Pro. No biggie! To ensure your cooler will continue performing just as

well as always grab a pen and write down the settings from your old CoolBot:

✓ Room Set Point: _______

Push either arrow key on your CoolBot until the Room Mode light is lit. Press

the checkmark and the current setpoint will blink.

✓ Fins Setting: _______

Push either arrow key on your CoolBot until the Fins Mode light is lit. Press

the checkmark and the current Fins Setting will blink.

✓ Heater delay: _______

Push either arrow key on your CoolBot until the Heater Mode light is lit. Press

the checkmark three times and the current Heater Delay Setting will blink.

CoolBot Pro

Temperature

Sensors

CoolBot Jumper

Heater

Power Supply

Data Cable

PAGE 1
CoolBot Jumper CoolBot Pro Temperature Sensors Qty 1 1 2 1 1 1 Heater Item CoolBot Pro CoolBot Jumper Temperature Sensors Heater Data Cable Power Supply Power Supply Data Cable Description Patented Digital Temperature Controller Wi-Fi Radio Signal Module Sensor Cables (Blue Cable - Black Tip) with external 2.5mm jack connector CoolBot Heater Cable (Black Cable - Red Tip) with external 2.
PAGE 2
CONNECTING YOUR COOLBOT PRO TO YOUR WI-FI NETWORK CoolBot Pro and CoolBot Jumper Set Up STEP 1 Unpack the CoolBot Pro in an area with good Wi-Fi reception (outside of your cooler). Plug in the Temperature Sensors and the Heater Cable into the corresponding ports (See diagram on page 4). Don’t connect the cables to your A/C and don’t plug in the power supply. STEP 2 Connect the CoolBot Jumper to the CoolBot Pro using ONLY the provided silver/grey Data Cable.
PAGE 3
INSTALLING YOUR COOLBOT PRO TO YOUR A/C (See Diagram on page 4) STEP 1 Plug the wires into the corresponding labeled ports at the bottom of the CoolBot Pro except for the Data Cable. If you are replacing an existing CoolBot with removable Temperature Sensors and Heater Cables you can leave them in place and connect them to the CoolBot Pro. The CoolBot Pro works with both black and blue Temperature Sensor Cables. STEP 2 Mount the CoolBot Pro on the wall next to the A/C.