P2P IP CAMERA Network Installation Manual QuickCamera Installation Manual HBP O-P
Network Camera Installation Manual 1. Hardware installation 1.1 Hardware connection Connect the power supply and network cable. Check if the power indicator (green) and the network indicator (yellow) is working properly. Then the camera head will rotate automatically. WIFI antenna I/O port Power input Power indicator RJ45 Network indicator Audio out Reset Button SD slot T/F Fig 1.1 Note: picture is for reference only. Actual product may vary. Power indicator: Green LED is on while power is on.
Network Camera Installation Manual 1.2 Network connection If you camera has one key set up feature, you do not need to connect the network cable between the camera and WiFi router.) Skip to 1.4. T/F Fig 1.2 1.3 Wifi Connectin using WPS button (If your router or camera does not have WPS button, please skip this step.
Network Camera Installation Manual 1.4 WiFi Connection using “one key setup.” Plug in the power adapter to the camera. The camera head will rotate to initialize for about 10 seconds. For the first time installation, after downloading and installing “coolcamHBP” app, tap on add camera and tap on “one key setup wifi” icon or choose skip (only if camera wifi setup is done.) Fig 1.4a Fig 1.4b Fig 1.
Network Camera Installation Manual 2.2 Add camera There are 3 ways to add camera to the app: Lan Search, QR Code Scan and Manual input. Factory default user name is “admin” default password is “admin”. Please note that the password on some models are empty. In this case, leave the password section empty and proceed to complete the adding procedure. Method 1:Tap“ + ” to add cameras, then tap Search network. This will find all the cameras in the same network.
Network Camera Installation Manual Method 3:Tap“ + Add Device ” to add camera, then manually input all the information into the system. Name your camera by your choice, input the Camera ID, then input Username and finally input factory default password. Once all of the information have been added, tap “Save” on the right top corner to finish adding process. Fig 2.2g Fig 2.2h Fig 2.2i TIP When the password is same as the factory default password, it will remind you (Fig 2.
Network Camera Installation Manual 3.2 Multi view screen Fig 3.2b Fig 3.2a Control icons explained. monitor/ intercom talk alarm switch preset position switch Flips around resolution Snapshot Record Video Infrared lamp switch flip top to bottom current setting Monitor/intercom – Listen to the audio of the camera. Talk – Talk back to the camera for two way audio Snapshot – Take picture of the screen and store on camera's memory.
Network Camera Installation Manual 4. Parameter Setting Click on“ ” to enter setting. You will see Security Code setting, wifi settings, SD card settings, alarm settings, FTP settings, mail settings and reboot camera. 4.1 Security Code Setting ”to enter edit interface, Tap on “Advanced setting” to modify In camera list, Tap on“ the security password. The factory default ID and password is both “admin”. Fig 4.1a Fig 4.1b Fig 4.1c 4.
Network Camera Installation Manual 4.3. SD Card Setting For motion detection setting: Turn on “Guard”, choose the sensitivity, alarm SD card recording, push notification, and remote saving pictures. Fig 4.3a Fig 4.3b 4.4. SD Card Setting In Advanced mode, tap on SD card to format the SD card. Warning: tapping “Continue” will erase all data. Fig 4.4a Fig 4.
Network Camera Installation Manual 4.6 Time setting 4.5 Alarm Setting 4.5a For motion detection setting, Follow below setting Fig 4.5a 4.5b For external alarm setting, Follow below setting Fig 4.5b Turn on Local Time Correction to Synchronize time with your phone. Fig 4.6 5.1 Check alarm push notification live video Tap on the push notifications, it will connect you to live video of the camera triggered. To check recorded event video, please go to 5.2 below. Fig 5.1a Fig 5.
Network Camera Installation Manual 5.2 Check Event Video Tap on “Event” icon. Fig 5.3a Tap on video file. Fig 5.3b View event video Fig 5.4c 6. Introduction of Android App 6.1 App download From Play Store, search for app name “coolcamHBP”, and then choose “ download and install it. ” to 6.2 Add Camera There are 3 ways to add camera to the app: Lan Search, QR Code Scan and Manual input. Factory default user name is “admin” default password is “admin”.
Network Camera Installation Manual Method 2:By QR Code Scan Tap“ ” to add cameras, tap Scan QR code, scan the QR code located at the bottom + Add Device of the camera. Then, name your camera and input factory default password. Fig 6.2d Fig 6.2e Fig 6.2f Method 3: Manually add Tap“ ” to add cameras, type in camera's UID and password manually to connect to the camera. Fig 6.2g Fig 6.2h Fig 6.
Network Camera Installation Manual 7. Live View Screen 7.1 Single view Screen Tap on the picture to see live view Fig 7.1a Fig 7.1b 7.2 Multi-view Screen Tap on the quad view icon on top left corner to see quad view. Fig 7.2a Fig 7.2b Control icons explained.
Network Camera Installation Manual Monitor/intercom – Listen to the audio of the camera. Talk – Talk back to the camera for two way audio Snapshot – Take picture of the screen and store on camera's memory. Record – Record video of the live view and store on camera's memory. Alarm on – Turn on alarm. Preset – Tap on the icon to point the camera to preset position. Set position on pan and tilt camera by pressing and hold for 3 seconds. IR light – Turn on IR LED light.
Network Camera Installation Manual 8.2 WIFI Settings In the “Advanced Setting”, Tap “Manage WIFI networks”, select your WIFI router you want to connect the camera to. Then input password of the WiFi router. After successful setting, camera will reboot. After reboot, LAN cable can be unplugged. Fig 8.2a 8.3 Record Setting Fig 8.2b 8.
Network Camera Installation Manual 9.1. Check the Event Video Tap on Event message Select video file from the list View event video Fig 9.1a Fig 9.1b Fig 9.1c 9.2 View Snapshot Stored in your phone. Fig 9.2a Fig 9.2b 15 Fig 9.
Network Camera Installation Manual 9.3 View Recorded Video Stored in your phone. Fig 9.3a Fig 9.3b 16 Fig 9.
Network Camera Installation Manual TIPS *When you first install Micro SD card, Micro SD card required to be formatted in the APP. *After the camera is powered on for about 30s, the camera will rotate a circle automatically. *After the camera is added in LAN successfully, no further setup is required for remote access. *In setting up a wireless connection, please make sure the wireless signal strength is strong.
Network Camera Installation Manual Restore the Factory Default Settings Find the "RESET" button at the bottom of the camera, make sure power is connected during resetting. Press and hold it for approximately 30 to 40 seconds to restores the factory settings (Yellow LED will become solid and then device will automatically restart). T/F For tech support, please contact support@ismartzon.com or visit www.ismartzon.
Eu Environmental protection Waste electronic products should not be household waste . If there is a corresponding Facilities , recycling . The recycling proposal , please consult the relevant functional departments of local government or retailers.