User's Manual

Health and Safety Information
Important Health Information and Safety Precautions
When using this product, the safety precautions below must be
taken to avoid possible legal liabilities and damages. Retain and
follow all product safety and operating instructions.
Observe all warnings in the product operating instructions. To
reduce the risk of bodily injury, electric shock, fire and damage to
the equipment, closely observe all of the following precautions.
Safety Precautions for Proper Grounding Installation
Caution: Connecting to improperly grounded equipment can result
in an electric shock to either you or your device. This product is
equipped with a USB Cable for connecting to a desktop or
notebook computer. Be sure your computer is properly grounded
before connecting this product to the computer. The power supply
cord of a desktop or notebook computer has an equipment-ground-
ing conductor and a grounding plug. The grounding plug must be
plugged into an appropriate outlet which is properly installed and
grounded in accordance with all local codes and ordinances.
Safety Precautions for Power Supply Unit
Use the correct external power source. A product should be
operated only from the type of power source indicated on the
electrical ratings label. If you are not sure of the type of power
source required, consult your authorized service provider or local
power company. For a product that operates from battery power or
other sources, refer to the operating instructions that are included
with the product.
Electrical Safety
This product is intended for use when supplied with power from the
designated battery or power supply unit. Other usage may be
dangerous and will invalidate any approval given to this product.
Handle battery packs carefully. This product contains a Li-ion
battery. There is a risk of fire and burns if the battery pack is
handled improperly. Do not attempt to open or service the battery
pack. Do not disassemble, crush, puncture, short external contacts
or circuits, dispose of in fire or water, or expose a battery pack to
temperatures higher than 60°C (140°F).
Note: Danger of explosion if battery is incorrectly replaced. Replace
only with specified batteries. To replace the battery, take the device
to an authorized service centre. Recycle or dispose of used batteries
according to all applicable local regulations, or in accordance with
the instructions in the reference guide.
Safety Precautions for Direct Sunlight
Store this product away from excessive moisture and extreme
temperatures. Do not leave the product or its battery inside a
vehicle or in places where the temperature may exceed 60°C
(140°F), such as on a car dashboard, window sill, or behind glass
that is exposed to direct sunlight or strong ultraviolet light for
extended periods of time. This may damage the product, overheat
the battery, or pose a risk to the vehicle.
Environmental Restrictions
Do not use this product in gas stations, fuel depots, chemical plants
or where blasting operations are in progress, or in potentially
explosive atmospheres such as fueling areas, fuel storehouses,
below deck on boats, chemical plants, fuel or chemical transfer or
storage facilities, and areas where the air contains chemicals or
particles, such as grain, dust, or metal powders. Please be aware
that sparks in such areas could cause an explosion or fire resulting in
bodily injury or even death.
Follow these other specific precautions:
1. Keep the battery or device dry and away from water or any liquid
as it may cause a short circuit.
2. The device should be connected only to products that bear the
USB-IF logo or have completed the USB-IF compliance program.
3. Keep metal objects away so they do not come in contact with
the battery or its connectors as it may lead to short circuit during
operation.
4. Always keep the battery out of the reach of babies and small
children to avoid swallowing. Consult a doctor immediately if the
battery is swallowed.
5. Do not use a battery that appears damaged, deformed,
discolored, has any rust on its casing, if it overheats, and/or if it
emits a foul odor.
6. Use of an unqualified battery or charger may present a risk of
fire, explosion, leakage or other hazard.
7. Only use the battery with a charging system that has been
qualified with the system per this standard: IEEE-Std-1725-200x.
8. Avoid dropping the device or battery. If the device or battery is
dropped, especially on a hard surface causing damage, take it to a
service center for inspection.
9. If the battery leaks: Do not allow the leaking fluid to come in
contact with eyes. If contact occurs, DO NOT rub the eyes. Rinse
with clean water immediately and seek medical advice. Do not allow
the leaking fluid to come in contact with skin or clothing. If contact
occurs, flush the affected area immediately with clean water and
seek medical advice. Take other precautions to keep a leaking
battery away from fire as there is a danger of ignition or explosion.
Health & Safety
Warranty Guide
Part of Statement 15.105:
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If you experience interference with reception (e.g., television),
determine if this equipment is causing the harmful interference by
turning the equipment off and then back on to
see if the interference is affected.
If necessary, try correcting the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
further assistance.
TIA Safety Information
The following is the complete TIA Safety Information for wireless
handheld devices:
Exposure to Radio Frequency Signal
Your wireless handheld portable device is a low-power radio
transmitter and receiver. When ON, it receives and sends out Radio
Frequency (RF) signals. In August 1996, the Federal
Communications Commissions (FCC) adopted RF exposure
guidelines with safety levels for handheld wireless devices. Those
guidelines are consistent with the safety standards previously set by
both U.S. and international standards ‘bodies, as follows:
ANSI C95.1 (1992) *
NCRP Report 86 (1986)
ICNIRP (1996)
* American National Standards Institute; National Council on
Radiation Protection and Measurements; International Commission
on Non-Ionizing Radiation Protection. Those standards were based
on comprehensive and periodic evaluations of the relevant scientific
literature. For example, over 120 scientists, engineers, and physicians
from universities, government health agencies, and industry
reviewed the available body of research to develop the ANSI
Standard (C95.1). The design of your device complies with the FCC
guidelines (and those standards).
Battery Information and Precautions
To assure product safety, there shall be precautions below.
Danger!
- Use compatible chargers and follow the specified conditions when
charging the cell.
- Use the cell only with the specified equipment.
- Do not put or store cell together with metal articles such as
necklaces, hairpins, coins, or screws.
- Do not short circuit the (+) and (-) terminals with metal
conductors.
- Do not place cell in a device with the (+) and (-) in a reverse way.
- Do not penetrate cell with a sharp articles such as a needle.
- Do not disassemble the cell.
- Do not weld the cell directly.
- Do not use a seriously damaged or deformed cell.
- Thoroughly read the user’s manual before use. Inaccurate handling
of lithium ion cell may result in heat, fire, explosion, damage or the
capacity loss of the cell.
Warning!
- Do not put cell into a heating vessel, washing machine or
high-pressure container.
- Do not use cell with primary batteries, or batteries of a different
package, type, or brand.
- Stop charging the cell if charging is not completed within the
specified time.
- Stop using the cell if abnormal heat, odor, discoloration,
deformation or abnormal condition is detected during use, charge,
or storage.
- Keep away from cell immediately when leakage or foul odor is
detected.
Non-ionizing Radiation
Your device has an internal antenna. This product should be
operated in its normal-use position to ensure the radiative
performance and safety from interference. As with other mobile
radio transmitting equipment, users are advised that for satisfactory
operation of the equipment and for personal safety, it is
recommended that no part of the human body should come too
close to the antenna during equipment operation.
Use only the supplied integral antenna. Use of unauthorized or
modified antennas may impair call quality and damage the device,
causing loss of performance and SAR levels exceeding the
recommended limits, as well as causing non-compliance with local
and national regulatory requirements. In order to limit RF energy
exposure and to ensure optimal device performance, operate the
device only in its normal-use position. Contact with the antenna
area may impair call quality and cause your device to operate at a
higher power level than needed which can reduce antenna
performance and battery life.
- Wash well with clean water immediately if liquid leaks onto your
skin or clothes.
- If liquid leaking from the cell gets into your eyes, do not rub your
eyes. Wash them well with clean water and call physician
immediately.
Caution!
- Store batteries out of reach of children so that they are not
accidentally swallowed or handled.
- If younger children use the cell, their guardians should explain the
proper handling.
- Be sure to read the user’s manual and cautions on handling
thoroughly before using the cell.
- Batteries have cycle life. Replace failed cell with a new cell that is
the same brand immediately after normal life cycle expiration, or if
expiration has occurred prematurely.
Store battery in a low-humidity and low-temperature environment if
the battery won’t be used for an extended period of time.
- Keep it far away from articles or materials with static electric
charges while the cell is charged, used or stored.
- Wipe with a dry cloth before using the cell if the terminals of the
cell become dirty.
Safety Instructions for Charging
Please read the following information carefully.
1. The maximum ambient temperature of the charger shall not
exceed 40°C (104 degrees F).
2. The charger shall be installed according to specification. The
current of load and output power shall not exceed the following
value:
Input: AC100-240V~ 50/60Hz 0.15A
Output: DC5V 1A
FCC Notice and Cautions
This device and its accessories comply with Part 15 of FCC Rules.
Operation is subject to the following conditions:
(1) This device and its accessories may not cause harmful
interference.
(2) This device and its accessories must accept any interference
received, including interference that may cause undesired operation.
Part 15.21 Statement：
Changes or modifications that are not expressly approved by the
manufacturer could void the user’s authority to operate the
equipment.
Aircraft Safety
Due to the possible interference caused by this product to an
aircraft’s navigation system and its communications network, using
this device’s function on board an airplane is prohibited in most
countries.
Safety Precautions for RF Exposure
1. Use of non-original, non-manufacturer-approved accessories may
violate your local RF exposure guidelines and should be avoided.
2. Use only original, manufacturer-approved accessories when such
accessories contain metal of any kind.
3. Avoid using your device near strong electromagnetic sources,
such as microwave ovens, sound speakers, TV and radio.
4. Avoid using your device near metal structures (for example, the
steel frame of a building).
Explosive Atmospheres
When in an area with a potentially explosive atmosphere or where
flammable materials exist, the device should be turned off and the
user should obey all signs and instructions. Sparks in such areas
could cause an explosion or fire resulting in bodily injury or even
death. Users are advised not to use the equipment at refueling
points such as service or gas stations, and are reminded of the need
to observe restrictions on the use of radio equipment in fuel depots,
chemical plants, or where blasting operations are in progress. Areas
with a potentially explosive atmosphere are often, but not always,
clearly marked such as fueling areas, below deck on boats, fuel or
chemical transfer or storage facilities, and including, but not limited
to areas where the air contains chemicals or particles such as grain,
dust, or metal powders.
Interference with Medical Equipment Functions
This product may cause medical equipment to malfunction. The use
of this device is prohibited in most hospitals and medical clinics for
which regulations and rules are commonly posted in such facilities.
In these instances, turn your device OFF as health care facilities
frequently use equipment that is adversely affected by RF energy. If
you use any personal medical device(s), consult the manufacturer of
your device(s) to determine if the device(s) is adequately shielded
from external RF energy. Your health care provider may be able to
assist you in obtaining this information.
Antenna Care
Use only the supplied or approved replacement antenna.
Unauthorized antennas, modifications, or attachments could
damage the device and may violate FCC regulations.
Pacemakers
The Health Industry Manufacturers Association recommends that a
minimum separation of six (6) inches be maintained between a
handheld wireless device and a pacemaker to avoid potential
interference with the pacemaker. These recommendations are
consistent with the independent research by and recommendations
of Wireless Technology Research.
Persons with pacemakers:
1. Should ALWAYS keep the device more than six (6) inches from
their pacemaker when the device is turned ON;
2. Should not carry the device in a breast pocket;
3. Should use the ear opposite the pacemaker to minimize the
potential for interference;
4. Should turn the device OFF immediately if there is any reason to
suspect that interference is occurring.
Electronic Devices
Most modern electronic equipment is shielded from RF signals but
some equipment or devices might not be.
Hearing Aids
Some digital wireless devices may interfere with hearing aids. In the
event of such interference, you please consult your service provider,
or call customer service regarding alternatives.
Other Medical Devices
If you use other personal medical devices, consult the device
manufacturer to determine if it is adequately shielded from external
RF energy, or your health care provider may be able to advice about
any harmful device interactions.
Vehicles
RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles. Be certain to contact the
manufacturer or representative regarding this as well as
manufacturer of any additional vehicle equipment.
Posted Facilities
Turn your device OFF in any facility where posted notices so require.
For Vehicles Equipped with an Air Bag
DO NOT place objects, including installed or portable wireless
equipment, in the area over the air bag or in the air bag deployment
area. If in-vehicle wireless equipment is improperly installed and the
air bag inflates, serious injury could result since air bags inflate with
great force.
Safety Information
Please read and observe the following information for safe and
proper use of your device and to prevent damage. Also, keep the
user guide in an accessible place after reading it for ease in locating
it for future reference.
Violation of the instructions may cause minor or serious damage to
the product.
1. Do not disassemble, open, crush, bend or deform, puncture or
shred your equipment.
2. Do not modify or remanufacture your equipment. Do not
attempt to insert foreign objects into the battery. Do not immerse
your equipment in water or other liquids, or expose it to water or
other liquids, fire, explosions or other hazards.
3. Do not short-circuit the battery or allow metallic conductive
objects to contact the battery terminals.
4. Avoid dropping the device. If the device is dropped on a
hard surface or elsewhere, take it to a service center for inspection if
damage is suspected.
Charger and Adapter Safety
1. Only use compatible battery and charger so as to avoid serious
damage to your device.
2. When traveling abroad, only use compatible battery pack
charger along with the correct device adapter.
Battery Information: Care and Proper Disposal
1. Please dispose of your battery properly or take it to your local
wireless carrier for recycling.
2. The battery doesn’t need to be empty before recharging, and
replace the battery when it no longer provides acceptable
performance. Note: The battery can be recharged several hundred
times and it does not need to be empty in order to recharge.
3. Do not disassemble or short-circuit the battery.
4. Keep the battery’s metal contacts clean.
5. Metallic articles that come into contact with the device may
short-circuit the + and – battery terminals (metal strips) which may
result in battery damage, or even an explosion.
General Notice
1. Using a damaged battery or placing a battery in your mouth may
cause serious injury.
2. Placing items containing magnetic strip components (e.g.: credit
cards, device cards, bank books, subway tickets) near your device
may damage the data stored in the magnetic strips.
3. Talking on the device for long periods of time may reduce call
quality due to heat generation.
4. Do not use the device if the antenna is damaged as it may cause
a slight contact burn. Please communicate with the Authorized
Service Center to replace the damaged antenna.
5. Do not immerse your device in water. If this happens,
immediately turn the device OFF and remove the battery. If the
device does not work, take it to the Authorized Service Center.
6. Do not paint your device.
7. Device data, including contact information, ringtones, text
messages, voice messages, etc., may be inadvertently deleted due
to careless use, device repair, or software upgrades. Please back up
your important device numbers and all other vital data. Note:
Neither the manufacturer nor any person or entity associated
therewith is liable for any damages whatsoever due to loss of any or
all data stored on any of your devices.
8. Do not turn your device on or off while the device is in close
proximity to your ear.
5. Recharge the battery after long periods of non-use to maximize
battery life. Note: Battery life will vary due to usage patterns and
environmental conditions.
6. Use of extended backlighting, Browser, and data connectivity
kits affect battery life as well as talk/standby times.
7. The self-protection function of the battery cuts the power of the
device when its operation is in an abnormal state. In this case,
remove the battery from the device, reinstall it, and turn the device
on.
Explosion, Shock, and Fire Hazards
1. Do not put your device in a place that is subject to excessive
dust, and always keep the minimum required distance between the
power cord and heat sources.
2. Unplug the power cord prior to cleaning your device, and clean
the power plug pin when necessary.
3. When using the power plug, ensure that it’s firmly connected.
4. Placing the device in a pocket or bag without covering the
device receptacle (power plug pin), metallic articles (e.g.: coins,
paperclips, pens) may short-circuit the device. Always cover the
receptacle when not in use.
Consumer Information on SAR
This Model Device Meets the Government’s Requirements for
Exposure to Radio Waves. Your wireless device is a radio transmitter
and receiver. It is designed and manufactured not to exceed the
emission limits for exposure to radiofrequency (RF) energy set by
the Federal Communications Commission (FCC) of the U.S.
Government. These FCC exposure limits are derived from the
recommendations of two expert organizations, the National Council
on Radiation Protection and Measurement (NCRP) and the Institute
of Electrical and Electronics Engineers (IEEE). In both cases, the
recommendations were developed by scientific and engineering
experts drawn from industry, government, and academia after
extensive reviews of the scientific literature related to the biological
effects of RF energy. The exposure limit for wireless mobile devices
employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR is a measure of the rate of absorption of RF
energy by the human body expressed in units of watts per kilogram
(W/kg). The FCC requires wireless devices to comply with a safety
limit of 1.6 watts per kilogram (1.6 W/kg). The FCC exposure limit
incorporates a substantial margin of safety to give additional
protection to the public and to account for any variations in
measurements. Tests for SAR are conducted using standard
operating positions specified by the FCC with the device
transmitting at its highest certified power level in all tested
frequency bands. Although SAR is determined at the highest
certified power level, the actual SAR level of the device while
operating can be well below the maximum value. Because the
device is designed to operate at multiple power levels to use only
the power required to reach the network, generally, the closer you
are to a wireless base station antenna, the lower the power output.
Before a device model is available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the limit
established by the government adopted requirement for safe
exposure. The tests are performed in positions and locations (e.g.,
next to the head and worn on wrists) as required by the FCC for
each model. This device was tested for typical body-worn
operations with the back of the device kept 0 inches (0 cm)
between the user’s body and the back of the device. To comply with
FCC RF exposure requirements, a minimum separation distance of 0
inches (0 cm) must be maintained between the user's body and the
back of the device. Third-party belt clips, holsters, and similar
accessories containing metallic components should not be used.
Body-worn accessories that cannot maintain 0 inches (0 cm)
separation distance between the user's body and the back of the
device, and have not been tested for typical body-worn operations
may not comply with FCC RF exposure limits and should be
avoided.
The FCC has granted an Equipment Authorization for this model
device with all reported SAR levels evaluated as in compliance with
the FCC RF emission guidelines.
The highest SAR value for this model device when tested for use
next to the head is 1.42 W/kg and when worn on the hands, wrists
or ankles, as described in this user’s manual, is 1.54 W/kg. While
there may be differences between SAR levels of various devices
and at various positions, they all meet the government
requirement for safe exposure.
SAR information on this model device is on file with the FCC and
can be found under the Display Grant section of http://www.fcc.gov-
/oet/ea/fccid/ after searching on FCC ID: R38YL303C.
To find information that pertains to a particular model device, this
site uses the device FCC ID number which is usually printed
somewhere on the case of the device. Sometimes it may be
necessary to remove the battery pack to find the number. Once you
have the FCC ID number for your device, follow the instructions on
the website and it should provide values for typical or maximum
SAR for that device.
Additional information on Specific Absorption Rates (SAR) can be
found on the Cellular Telecommunications Industry Association
(CTIA) website at http://www.ctia.org/
In the United States and Canada, the SAR limit for mobile devices
used by the public is 1.6 watts/kg (W/kg) averaged over one gram
of tissue. The standard incorporates a substantial margin of safety
to give additional protection for the public and to account for any
variations in measurements.
IC
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Note: Some content and services accessible through this device
belong to third parties and are protected by copyright, patent,
trademark and/or other intellectual property laws. Such content and
services are provided solely for your personal noncommercial use.
You may not use any content or services in a manner that has not
been authorized by the content owner or service provider. Without
limiting the foregoing, unless expressly authorized by the applicable
content owner or service provider, you may not modify, copy,
republish, upload, post, transmit, translate, sell, create derivative
works, exploit, or distribute in any manner or medium any content
or services displayed through this device.
“THIRD PARTY CONTENT AND SERVICES ARE PROVIDED “AS IS.”
NEITHER COOLPAD NOR ANY AFFILIATE THEREOF
(COLLECTIVELY, "COOLPAD") WARRANT IN ANY MANNER
CONTENT OR SERVICES SO PROVIDED, EITHER EXPRESSLY OR
IMPLIEDLY, FOR ANY PURPOSE. COOLPAD EXPRESSLY DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFERINGEMENT. COOLPAD
DOES NOT GUARANTEE THE ACCURACY, VALIDITY, TIMELINESS,
LEGALITY, OR COMPLETENESS OF ANY CONTENT OR SERVICE
MADE AVAILABLE THROUGH THIS DEVICE AND UNDER NO
CIRCUMSTANCES, INCLUDING NEGLIGENCE, SHALL COOLPAD BE
LIABLE, WHETHER IN CONTRACT OR TORT, FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES,
ATTORNEY FEES, EXPENSES, OR ANY OTHER DAMAGES ARISING
OUT OF, OR IN CONNECTION WITH, ANY INFORMATION
CONTAINED IN, OR AS A RESULT OF THE USE OF ANY CONTENT
OR SERVICE BY YOU OR ANY THIRD PARTY, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.”
Third party services may be terminated or interrupted at any time,
and Coolpad makes no representation or warranty that any content
or service will remain available for any period of time. Content and
services are transmitted by third parties by means of networks and
transmission facilities over which Coolpad has no control. Without
limiting the generality of this disclaimer, Coolpad expressly disclaims
any responsibility or liability for any interruption or suspension of
any content or service made available through this device. Coolpad
is neither responsible nor liable for customer service related to the
content and services. Any question or request for service relating to
the content or services should be made directly to the respective
content and service provider.
Children’s Privacy
For Coolpad to continue to provide you and your child the best
service, we need to collect your child’s personal information.
Personal information collected may include but not be limited to the
name, birthday, email address, and phone number of the user. It can
also include opinions, spending habits, IP address, photos and
digital images, and email and text messages.
In accordance with US federal law, Children’s Online Privacy
Protection Act (“COPPA”) and Canadian law and the Personal
Information Protection and Electronic Documents Act (“PIPEDA”)
your consent in required for the collection of such personal
information in lieu of your child, including cases such as when:
• Giving access to features that allow the sharing of personal
information in a public setting or with other users (e.g. chat, image
of face, recording of voice, full name, telephone number, any
personal information in voice recording);
• Giving a child access to third party plug-in features;
• Collecting and uploading a child’s geolocation information;
• Collecting or using a child’s personal information and sending the
child ongoing newsletters or other alerts (e.g. push notifications);
• Collecting a child’s personal information in connection with any
other features or activities;
• Collecting and using a persistent identifier, unless such persistent
identifier is used for internal support purposes only;
• Sharing a child’s personal information with third parties;
• Collecting or using a child’s personal information for significantly
new purposes not previously consented to by you.
Once consent has been given, you can withdraw your consent and
ask us to not collect any further information and/or delete
previously collected information, at any time.
We share some data with third parties, specifically for providing
services essential to the functionality of the Dyno Smartwatch. The
list of such third parties can be found at https://coolpad.us/priva-
cy-policy/. You have the right to ask us not to share data with any
third parties. However, in such instances, we may not be able to
provide all services and functionalities, for example the geolocation
service provided by Google.
THIS LIMITED WARRANTY SETS OUT THE FULL EXTENT OF
COOLPAD'S RESPONSIBILITIES, AND THE EXCLUSIVE REMEDY
REGARDING THE PRODUCTS. ALL DISPUTES WITH COOLPAD
ARISING IN ANY WAY FROM THIS LIMITED WARRANTY OR THE
SALE, CONDITION OR PERFORMANCE OF THE PRODUCTS SHALL
BE RESOLVED EXCLUSIVELY BY ANY COURT WITH COMPETENT
JURISDICTION. Any such dispute shall not be combined or
consolidated with a dispute involving any other person's or entity's
Product or claim, and specifically, without limitation of the
foregoing, shall not under any circumstances proceed as part of a
class action. The laws of the State of California, without reference to
its choice of laws principles, shall govern the interpretation of the
Limited Warranty and all disputes arising out of the products or
services.
This settlement of disputes also applies to claims against
COOLPAD'S employees, contractors, agents, and/or other
representatives, as well as any of all of its affiliated entities,
regardless of place of incorporation, if any such claim arises from
the Product's sale, condition or performance. Notwithstanding the
foregoing, neither this warranty nor provision of any Product shall,
in and of itself, provide for in persona jurisdiction over any of
COOLPAD's employees, contractors, agents, and/or other
representatives, or over its affiliated entities.
Severability
If any portion of this Limited Warranty is held to be illegal or
unenforceable, such partial illegality or unenforceability shall not
affect the enforceability of the remainder of the Limited Warranty.
Coolpad Technologies, Inc.
Email: [e-mail]
Customer Service: 1-877-606-5753
Standard Limited Warranty
(This standard Limited Warranty supersedes and replaces for all
purposes the Standard Limited Warranty that appears in the
enclosed documentation, if any)
COOLPAD TECHNOLOGIES, INC.("COOLPAD") warrants that
COOLPAD's devices and accessories enclosed herein ("Products")
are free from defects in material and workmanship under normal use
and service for the period commencing upon the date of purchase
by the first consumer purchaser and continuing for the following
specified period of time after that date:
Device 12 months
Battery 6 months
Other Accessories(If included in the box set) 3 months
This Limited Warranty is conditioned upon proper use of the
Products. This Limited Warranty does not cover: (a) defects or
damage resulting from accident, misuse, abnormal use, abnormal
conditions, improper storage, exposure to liquid, moisture,
dampness, sand or dirt, neglect, or unusual physical, electrical or
electromechanical stress; (b) scratches, dents and cosmetic
damage, unless caused by COOLPAD; (c) defects or damage
resulting from excessive force or use of a metallic object when
pressing on a touch screen; (d) equipment from which the serial
number and/or the enhancement data code have been removed,
defaced, damaged, altered, made illegible, and/or otherwise
tampered with; (e) ordinary wear and tear; (f) defects or damage
resulting from the use of Product in conjunction or connection with
accessories, products, or ancillary/peripheral equipment not
furnished or approved by COOLPAD; (g) defects or damage
resulting from improper testing, operation, maintenance, installation,
service, or adjustment not furnished or approved by COOLPAD; (h)
defects or damage resulting from external causes such as collision
with an object, fire, flooding, dirt, windstorm, lightning, earthquake,
exposure to weather conditions, theft, blown fuse, or improper use
of any electrical source; (i) defects or damage resulting from cellular
signal reception or transmission, viruses and/or other software
problems introduced into the Product; or
(j) Product used or purchased outside the United States. This
Limited Warranty covers batteries only if battery capacity falls
below 80% of rated capacity or the battery leaks, and this Limited
Warranty does not cover any battery if: (i) the battery has been
charged by a non-compatible battery charger; (ii) any of the seals
on the battery are broken or show evidence of tampering; or (iii) the
battery has been used in equipment other than the COOLPAD
device for which it is specified.
During the applicable warranty period, provided the Product subject
to the warranty claim is returned in accordance with the terms of
this Limited Warranty, COOLPAD will repair or replace such Product,
at COOLPAD'S sole option, without charge. COOLPAD may, at
COOLPAD's sole option, use rebuilt, reconditioned, or new parts or
components when repairing any Product, or may replace the
Product with a rebuilt, reconditioned or new Product. All other
repaired/replaced Products will be warranted for a period equal to
the remainder of the original Limited Warranty on the original
Product or for ninety (90) days, whichever is longer. All replaced
Products, parts, components, boards and equipment shall become
the property of COOLPAD. Except to any extent expressly allowed
by applicable law, transfer or assignment of this Limited Warranty is
prohibited.
To obtain service under this Limited Warranty, you must return the
Product to an authorized device service facility in an adequate
container for shipping, accompanied by the sales receipt or
comparable proof of sale showing the original date of purchase, the
serial number of the Product and the seller's name and address.
Replacement parts and related service manual and diagnostic tools
are available in our authorized service center within ninety (90)
days after launch of the Product. Replacement parts and/or services
are available for three years after the end of production of the
product. To obtain assistance on where to deliver the Product,
please call COOLPAD Customer Care at 1-877-606-5753. If
COOLPAD determines that any Product is not covered by this
Limited Warranty, you must pay all parts, shipping, and labor
charges for the repair or return of such Product.
You should keep a separate backup copy of any contents of the
Product before delivering the Product to COOLPAD for warranty
service, as some or all of the contents may be deleted or
reformatted during the course of warranty service.