Operation & Service Manual 823006 2/01 15G Series Horizontal Grinders 15 G L - XXX - X X X Series: 15 Grinder: Terminations: Throttle Terminations: L Lever 3T 2 1/2 3 In. 4 In. 3/8-24 Wheel Type: RPM: 90 140 120 180 For additional product information visit our website at http://www.clecotools.com NORTH AMERICA CooperTools P.O. Box 1410 Lexington, SC 29071 Guard: 25 3 4 W Type 1 Wheel EUROPE Cooper Power Tools GmbH & Co.
Safety Recommendations For your safety and the safety of others, read and understand the safety recommendations before operating any grinder. Always wear protective equipment and clothing. ! WARNING Impact resistant eye protection must be worn while operating or working near this tool. Caution: Faceshields do not provide unlimited protection against flying particles and are not to be considered as eye protection. ANSI Z87.1 states that separate eyewear shall be used.
Safety Recommendations The guard must be securely attached to the grinder with all bolts, nuts and lockwashers in place and torqued to 30 to 40 in. lbs. Warning and Instruction Label • Improper mounting • Imbalance • Improper shipment or storage • Exposure to water, solvents, high humidity, freezing and extreme temperatures • Mismatched speed ratings • Age 202595 & 202596 0 Cleco CAUTION MODEL SERIAL NO. 1 2 OVER Repetitive work motions and/or vibration can cause injury to hands and arms.
Safety Recommendations Cleco MODEL SERIAL NO. CAUTION STEEL DRUM Before beginning operations or after mounting a wheel, the tool must be run for one (1) minute in a protected enclosure to check the integrity or the wheel. During this time or any other time, no one should stand in front of or in line of the wheel. When starting work with a cold wheel, apply it gradually to the workpiece until the wheel becomes warm.
Safety Recommendations wrist trauma. Since they vary widely in design, material, thickness, vibration reduction, and wrist support qualities, it is recommended that the glove, tool wrap, or wrist support manufacturer be consulted for items designed for your specific application. WARNING! Proper fit of gloves is important. Improperly fitted gloves may restrict blood flow to the fingers and can substantially reduce grip strength. when the grinder is running and contribute to the vibration.
TYPE 1 WHEEL GUARD MOUNTING Wheel Guard Wheel Dia. Part No. 2-1/2"(62mm) 865787 3"(75mm) 865786 4"(100mm) 865988 Lock Washer Recessed Flanges (Driving) Wheel Dia. Part No. 2-1/2"(62mm), 3"(75mm) 865653 4"(100mm) 865990 WARNING Wheel Blotters Wheel Guard Retainer Bolt Torque to 30 to 40 in. lbs. MODEL SERIAL NO. Cleco CAUTION 844280 Spindle End Nut 842970 Driving Flange Key Recessed Flanges (Outer) Wheel Dia. Part No.
OPERATING AND SERVICE INSTRUCTIONS READ SAFETY RECOMMENDATIONS BEFORE CONNECTING TOOL. The 15G Series Grinders are designed to operate on 90 psig (6.2 bar) maximum air pressure, using a 3/8" hose up to 8' in length. If additional length is required, the next larger hose size may be connected to the 8' whip hose. LUBRICATION An automatic in-line filter- regulator- lubricator is recommended as it increases tool life and keeps the tool in sustained operation.
15G MOTOR & GOVERNOR RPM 842970 8656994 Part No.
15G HANDLE 202105 202106 869855 869856 843590 865698 847808 841552 863093 864375 864530 202337 844311 847710 865701 843590 844304 864387 832595 864531 SERVICE INSTRUCTIONS FOR 15G HANDLE DISASSEMBLY To disassemble the lever throttle handle, unscrew the throttle valve cap 864531. This will allow the complete throttle valve assembly to be removed from the handle. The oiler body on the handle may be removed from the front of the handle with the aid of spreaders. PART NO.
NOTES 10
NOTES 11
CooperTools 670 Industrial Drive Lexington, SC 29072 Phone: (803) 359-1200 Fax: (803) 359-2013 www.clecotools.
