INSTALLATION& OWNER’ S MANUAL WIRED CONTROL FOR AIR CONDITIONER Thank you very much for purchasing our product. Before using your unit, please read this manual carefully and keep it for future reference.
● This manual gives detailed description of the precautions that should be brought to your attention during operation. ● In order to ensure correct service of the wired control please read this manual carefully before using the unit. ● For convenience of future reference, keep this manual after reading it.
CONTENTS 1. SAFETY PRECAUTION.............................................................................. 1 2. INSTALLATION ACCESSORY.................................................................... 2 3. INSTALLATION METHOD...........................................................................4 4. SPECIFICATION.......................................................................................10 5. FEATURE AND FUNCTION OF THE WIRED CONTROL........................11 6.
1. SAFETY PRECAUTION Read the safety precautions carefully before installing the unit. Stated below are important safety issues that must be obeyed. WARNING Means improper handling may lead to personal death or severe injury. CAUTION Means improper handling may lead to personal injury or property loss. WARNING Please entrust the distributor or professionals to install the unit. Installation by other persons may lead to imperfect installation, lectric shock or fire.
2. INSTALLATION ACCESSORY Select the installation location Don’t install at the place where cover with heavy oil, vapor or sulfureted gas, otherwise, this product would be deformed that would lead to system malfunction. Preparation before installation 1. Please confirm that all the following parts you have been supply. No. Name Qty.
2. INSTALLATION ACCESSORY Precaution of install the wire control 1. This manual provides the installation method of wire control. Please refer to the wiring diagram of this installation manual to wire the wire control with indoor unit. 2. The wire control working in low voltage loop circuit.
3. INSTALLATION METHOD 1.Wired remote control structure size figure 18.5 122 83.5 120 Fig 3-1 46 62 2.
3. INSTALLATION METHOD 3.Wiring figure 4-core shielding wire The connective wires group-1 Mainboard CN40 The connective wires group-2 Fig 3-3 Connect the female joint of wires group from the mainboard with the male joint of connective wires group. (See Fig.3-3) Please connect the other side of connective wires group with the male joint of wires group leads from wire control. (See Fig.3-3) 4.
3. INSTALLATION METHOD 5. Fasten the back plate of the wire control For exposed mounting, fasten the back plate on the wall with the 3 screws (M4×20) and plugs. (Fig.3-5) Back plate Screws (M4×20) Fig 3-5 For flush-mounting, fasten the back plate on the switch box with 2 screws (M4×25) and fasten it on the wall with 1 screw (M4×20). (Fig.3-6) Switch box Back plate Screw (M4×20) Screws (M4×25) NOTICE Fig 3-6 Put on a flat surface.
3. INSTALLATION METHOD 6. Battery installation Fig 3-7 Put the battery into the installationsite and make sure the positive side of the battery is in accordance with the positive side of installationsite.(See Fig.3-7) Please set the time corrected on the first time operation. Batteries in the wire control can timing under power failure which ensure the time keep right. When the power restores, if the time displayed is not correct, it means the battery is dead and replace the battery.
3. INSTALLATION METHOD 7. Wiring Line groove A. For wiring in the slot, four outletting positions. There are three need cutting. Top side wire outlet Right side wire outlet Left side wire outlet Line groove Line groove Line groove Cutting place of top side wire outlet Bottom side wire outlet Cutting place of left side wire outlet Cutting place of right side wire outlet Fig 3-8 B.
3. INSTALLATION METHOD 8.Reattach the upper part of the wire control After adjusting the upper case and then buckle the upper case; avoid clamping the wiring during installation. (Fig 3-11) Fig 3-11 All the pictures in this manual are for explanation purpose only. Your wire control may be slightly different .The actual shape shall prevail.
4.
5. FEATURE AND FUNCTION OF THE WIRED CONTROL Feature: POWER LCD display. Malfunction code display: it can display the error code, helpful for service. 4-way wire layout design, no raised part at backside, more convenient to place the wires and install the device. Room temperature display. MODE FAN SPEED TIMER SWING SWING FOLLOW ME DELAY/DAY OFF CONFIRM BACK COPY Dimension: H×W×D (in/mm) 4.8x4.7x0.72/122×120×18.5 Weekly Timer.
6.
7.
7.
8. PREPARATORY OPERATION Set the current day and time 1 TIMER Press the TIMER button for 3 seconds or more. The timer display will flash. Press the button “ + ” or “ - ” to set the date. The selected date will flash. 2 3 TIMER The date setting is finished and the time setting is prepared after pressing TIMER button or there is no pressing button in 10 seconds. Press the button “+” or “-” to set the current time. Press repeatedly to adjust the current time in 1-minute increments.
9. OPERATION Remote signal receiving function The wired remote control can be a remote signal receiving device, you can use the wireless remote control to control the air-conditioner through the wired remote control when the system have been powered on. To start/stop operation Press the POWER button. POWER Operation lamp Air conditioner ON :Lit brightly Air conditioner OFF:Not lit To set the operation mode Operation mode setting Press the MODE button to set the operation mode.
9. OPERATION Fan speed setting FAN SPEED Press the FAN SPEED button to set the fan speed. (This button is unavailable when in the mode of Auto or Dry) Room temperature sensor selection FOLLOW ME Indoor Unit Press the FOLLOW ME button to select whether the room temperature is detected at the indoor unit or the wire control. When the Follow me function indication appears, the room temperature is detected at the wire control.
9. OPERATION Child lock function Press the button “+” and “-” simultaneously for 3 seconds to activate the child lock function and lock all buttons on the wire control. Press the buttons again for 3 seconds to deactivate the child lock function. When the child lock function is activated,the mark appears. keypad tone setting BACK COPY Press the button “BACK” and “COPY” simultaneously for 3 seconds to close the keypad tone. Press the buttons again for 3 seconds to open the keypad tone.
9. OPERATION Faceplate function (on some models) MODE 1.When the unit is off,Press the MODE button long to activate the faceplate function.The mark will flash. The F2 mark appears when the faceplate is adjusted. 2. Press the button “+” and “-” to control the lift and drop of the faceplate. Pressing the “+” button can stop the faceplate,while it is dropping. Pressing the “-” button can stop the faceplate,while it is lifting.
9. OPERATION Up-Down airflow direction and swing (on some models) SWING SWING Use button to adjust the Up-down airflow direction. 1.Press the button every time, the louver swings 6 degrees. 2.Press and hold the button for 2 seconds,it turns into up-down swing mode, press ti again to stop. When the Up-Down swing function is activated,the mark appears.
10. TIMER FUNCTIONS WEEKLY timer Use this timer function to set operating times for each day of the week. On timer Use this timer function to start air conditioner operation.The timer operates and air conditioner operation starts after the time has passed. Off timer Use this timer function to stop air conditioner operation.The timer operates and air conditioner operation stops after the time has passed. On and Off timer Use this timer function to start and stop air conditioner operation.
10. TIMER FUNCTIONS To set the On or Off TIMER 1 Press the TIMER button to select the TIMER or . No display 2 CONFIRM Press the CONFIRM button and the Clock display is flashing. 3 ex.Off timer set at PM 6:00 Press the button “ + ” or “ - ” to set the time. After the time is set, the timer will start or stop automatically. 4 Press the CONFIRM button again to finish the settings.
10. TIMER FUNCTIONS To set the On and Off TIMER 1 Press the TIMER button to select the . TIMER 2 Press the CONFIRM button and the Clock display is flashing. CONFIRM 3 CONFIRM Press the button “ + ” or “ - ” to set the time of On timer,and then press the CONFIRM button to confirm the setting. 4 Press the button “ + ” or “ - ” to set the time of Off timer. 5 Press the CONFIRM button to finish the settings.
11. WEEKLY TIMER 1 Weekly timer setting TIMER CONFIRM Press the TIMER button to select the to confirm. 2 and then press the CONFIRM button Day of the week setting CONFIRM Press the button “ + ” or “ - ” to select the day of the week.and then press the CONFIRM button to confirm the setting. 3 ON timer setting of timer setting 1 CONFIRM Press the button “ + ” or “ - ” to set the time of On timer.and then press the CONFIRM button to confirm the setting.
11. WEEKLY TIMER ex.Tuesday time scale 1 Up to 4 timer settings can be saved for each day of the week.It is conventent if the WEEKLY TIMER is set according to the user’s life style. 4 Off timer setting of timer setting 1 CONFIRM Press the button “ + ” or “ - ” to set the time of Off timer.and then press the Confirm button to confirm the setting. 5 6 ex.Tuesday time scale 1 Different timer settings can be setted by repeating step 3 to 4. Other days in one week can be setted by repeating step 2 to 5.
11. WEEKLY TIMER WEEKLY timer operation To activate WEEKLY TIMER operation Press the TIMER button while is displayed on the LCD. TIMER ex. To deactivate WEEKLY TIMER operation Press the TIMER button while TIMER is disappear from the LCD. ● To turn off the air conditioner during the weekly timer POWER 1. If press the POWER button once and quickly , the air conditioner will turn off temporarily. And the air conditioner will turn on automatically until the time of On timer.
11. WEEKLY TIMER To set the DAY OFF (for a holiday) 1 During the weekly timer, press the CONFIRM button. CONFIRM 2 Press the button “ + ” or “ - ” to select the day in this week . Press the DAY OFF button to set the DAY OFF. 3 The DELAY/DAY OFF mark is hidden ex.The DAY OFF is set for Wednesday 4 The DAY OFF can be setted for other days by repeating the steps 2 and 3. 5 Press the BACK button to back to the weekly timer. BACK To cancel:Follow the same procedures as those for setup.
11. WEEKLY TIMER DELAY function During the weekly timer, pressing the DELAY button once,display " ". Press this button twice, display " " and wait 3 seconds to confirm. It means the unit will override 1 hours; Press this button three times,display " " and wait 3 seconds to confirm. It means the unit will override 2 hours; DELAY/DAY OFF ex. If press the DELAY button to select “ ” at 18:05 , The air conditioner will delay to turn off at 20:05. Copy out the setting in one day into the other day.
11. WEEKLY TIMER 3 Press the COPY button,the letter “CY” will be shown on the LCD. COPY 4 Press the button “ + ” or “ - ” to select the day to copy to. 5 Press the COPY button to confirm . COPY The mark flashes quickly ex. Copy the setting of Monday to Wednesday 6 7 8 Other days can be copied by repeating step 4 and 5. Press the Confirm button to confirm the settings. CONFIRM Press the Back button to back to the weekly timer.
12. FAULT ALARM HANDING If the system does not properly operate except the above mentioned cases or the above mentioned malfunctions is evident, investigate the system according to the following procedures. NO. MALFU N C T ION & PROT EC T ION D EFIN E D ISPLAY DIGITAL TUBE 1 Error of communication between wire control and indoor unit F0 2 The faceplate is abnormal F1 Please check the error display of indoor unit and read <> if other error code appears. 13.
The design and specifications are subject to change without prior notice for product improvement.