Instruction Manual

9.2.2 RDG.CNF (READING CONFIGURATION)..............................................................................34
9.2.3 RDG SC (Reading Scale) AND RDG OF (Reading Offset)...................................................35
9.2.4 IN CNF (Input Configuration).................................................................................................36
9.2.5 IN.SC.OF (Input Scale And Offset)........................................................................................37
9.2.6 DEC PT (Decimal Point) ......................................................................................................... 38
9.2.7 CNT BY (Count By)................................................................................................................. 38
9.2.8 FIL.CNF (Filter Configuration)...............................................................................................39
9.2.9 FIL TI (Filter Time Constant)..................................................................................................40
9.2.10 SP CNF (Setpoints 1 & 2 Configuration) ............................................................................40
9.2.11 AL CNF (Alarm Configuration) ............................................................................................41
9.2.12 AL FNC (Alarm Function) ....................................................................................................42
9.2.13 AL RDG (Alarm Readings)................................................................................................... 43
9.2.15 AL DB (Alarm Deadband) ....................................................................................................43
9.2.16 OUT.CNF (Output Configuration)........................................................................................44
9.2.17 OT.SC.OF (Output Scale And Offset) .................................................................................45
9.2.18 BAUD (Baud Rate)................................................................................................................45
9.2.19 SERCNF (Serial Communication Configuration)...............................................................46
9.2.20 ADDRESS (Multipoint Communications Device Address) ............................................... 46
9.2.21 DAT FT (Data Format) ..........................................................................................................46
9.2.22 BUS FT (Bus Format) ........................................................................................................... 47
9.2.23 SERCNT (Serial Count) ........................................................................................................ 48
9.2.24 Analog Output Calibration Numbers ..................................................................................49
10.0 SETPOINTS/ALARMS .......................................................................................................49
10.1 Features Overview ......................................................................................................................50
10.2 Unlocking The Features .............................................................................................................50
10.3 Selecting SP CNF Setpoint Configuration Features ................................................................51
10.4 Deviation Function For Alarms..................................................................................................51
10.5 Selecting AL CNF Alarm Configuration Features ....................................................................52
10.6 Selecting AL FNC Alarm Function Features............................................................................. 53
10.7 AL RDG: Alarm Readings-Select Delay In Alarm Action.........................................................54
10.8 SP DB: Select “SP 1” and “SP 2” Deadband (Hysteresis) ...................................................... 54
10.9 AL DB: Select Alarm 1 (SP 3) and Alarm 2 (SP 4) Deadband (Hysteresis) ............................ 54
10.10 OUT .CNF: Control Flashing Of The Display ..........................................................................54
10.11 Entering Setpoint Levels (In Run Mode) .................................................................................55
11.0 PEAK AND VALLEY READINGS ......................................................................................55
12.0 ANALOG OUTPUT OPTION..............................................................................................55
12.1 Features Overview ......................................................................................................................56
12.2 Unlocking.....................................................................................................................................56
12.3 OUT.CNF: Configuring The Output ...........................................................................................56
12.4 OT.SC.OF: Setting Output Scale And Offset ............................................................................ 56
12.5 Board Installation: Entering The Trim Data ..............................................................................57
12.6 Filter Configuration FIL.CNF Value To Be Transmitted On Analog Output........................... 58
12.7 Wiring/Connections ....................................................................................................................58
13.0 BCD OPTION .....................................................................................................................58
13.1 Features Overview ......................................................................................................................58
13.2 BCD Card Jumper Table.............................................................................................................59
13.3 Interconnect Board .....................................................................................................................59
13.4 50-Line Cable Compatibility.......................................................................................................59
13.5 Selecting The Source Of BCD Data: “OUT .CNF” ....................................................................60
13.6 Hold Control ................................................................................................................................60
13.7 Data Ready Timing Pulses .........................................................................................................60
CF 67 iii M1291/N/0403 11279ML-02 Rev. A