Installation & Assembly

ManualsBrandsCooper Lighting LLC ManualsAll Security Lights & Flood Lights122-Watt LED Outdoor Security Wall Pack

INS #

Brand Logo

reversed out of

black

INS #

IB514014EN

Installation Instructions - WPLLED

Instructions d’installation - WPLLED

Instrucciones de instalación - WPMLLED

IMPORTANT: Read before installing ﬁxture. Retain for future reference.

SAFETY: This ﬁxture must be wired in accordance with the National Electrical Code and applicable local codes and

ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under

installation section.

WARNING

Make certain power is OFF before starting installation

or attempting any maintenance. Risk of fire/electric

shock. If not qualified, consult an electrician.

WARNING

Risk of Electric Shock—Disconnect power at fuse or

circuit breaker before installing or servicing.

WARNING

Risk of Burn—Disconnect power and allow fixture to

cool before servicing.

WARNING

Risk of Personal Injury—Fixture may become damaged

and/or unstable if not installed properly.

WARNING

DO NOT mount luminaire within 6” of a combustible

surface. DO NOT handle luminaire by the glass.

ote:N These instructions do not claim to cover all

details or variations in the equipment, procedure,

or process described, nor to provide directions

for meeting every possible contingency during

installation, operation or maintenance. When

additional information is desired to satisfy a

problem not covered sufficiently for user’s purpose,

please contact your nearest representative.

ote:N Specifications and dimensions subject to change

without notice.

Summary of content (8 pages)

PAGE 1
Brand Logo reversed out of black IB514014EN INS # Installation Instructions - WPLLED Instructions d’installation - WPLLED Instrucciones de instalación - WPMLLED WARNING Make certain power is OFF before starting installation or attempting any maintenance. Risk of fire/electric shock. If not qualified, consult an electrician. WARNING Risk of Electric Shock—Disconnect power at fuse or circuit breaker before installing or servicing.
PAGE 2
Installation Instructions - WPLLED INSTALLATION Applications These luminaires are designed for outdoor, wet location services and should not be used in areas with limited ventilation or in high ambient temperature enclosures. The luminaire shall be wall mount only. Inverted mounting will cause overheating and possible water entry. Tools Required Philips screwdriver, Torx T-20 bit (included), 6mm multi-bit screw driver or 6mm socket, 1/4” drill bit. 1.
PAGE 3
Instructions d’installation - WPLLED AVERTISSEMENT Assurez-vous que l'alimentation électrique est HORS TENSION avant de commencer l'installation ou de procéder à l'entretien. Risque d’incendie ou de décharge électrique. Si vous n’êtes pas qualifié, consultez un électricien. AVERTISSEMENT Risque de décharge électrique – Débranchez la source d'alimentation en enlevant le fusible ou en déclenchant le disjoncteur avant l'installation ou l'entretien.
PAGE 4
Instructions d’installation - WPLLED 2. Préparez la plaque dorsale pour le montage en perçant ou en ouvrant les trous appropriés. (Figure 3.) 3. Alignez la plaque dorsale sur la position voulue et fixez-la solidement. Calfeutrez tous les trous de la plaque dorsale et les trous de fixation et de conduite. Calfeutrez le contour de la plaque dorsale à l’endroit où le luminaire touche à la surface de montage pour assurer un scellage étanche. 4.
PAGE 5
Instrucciones de instalación - WPLLED ADVERTENCIA Asegúrese de que la alimentación esté DESCONECTADA antes de comenzar la instalación o intentar realizar cualquier tarea de mantenimiento. Riesgo de incendio y/o descarga eléctrica. Si no está calificado, consulte a un electricista. ADVERTENCIA Riesgo de descarga eléctrica: desconecte la alimentación en el disyuntor o fusible antes de instalar o realizar tareas de servicio técnico.
PAGE 6
Instrucciones de instalación - WPLLED 2. Prepare la placa trasera para montaje perforando o calando los orificios necesarios. (Figura 3.) 3. Alinee la placa trasera en el lugar deseado y móntela de manera segura. Selle todos los orificios de la placa trasera, los de montaje y de conductos. Selle alrededor de la placa trasera donde la luminaria hace contacto con la superficie de montaje para sellarla de forma hermética. 4.
PAGE 7
PAGE 8
Warranties and Limitation of Liability Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions. Garanties et limitation de responsabilité Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones. Eaton 1121 Highway 74 South Peachtree City, GA 30269 P: 770-486-4800 www.eaton.