Programming Manual

WaveLinx User Manual
www.cooperlighting.com
15
WaveLinx Wireless Area Controller 2 (Gen 2) continued
Wireless Area Controller Pushbutton Functions
The WaveLinx Wireless Area Controller 2 has two
pushbuttons that allow for several administrative
functions. These functions should be used with
caution!
Function Button Press Length WAC LED feedback Device outcome
Enter Pairing Mode Pair Press and release (1
second)
802.15.4 and LAN LEDs flash
Paired devices will exhibit paired behavior
described in the device reference sheets.
Unpaired devices can pair with the
Wireless Area Controller if they are in
pairing mode.
Exit Pairing Mode
(if pairing mode is still
active)
Pair Press and release (1
second)
802.15.4 LED ON steady
LAN LED returns to OFF or ON dependent
on connection to Ethernet and
configuration.
Paired devices will start operation within
the construction grouping. Lighting still in
the default construction area will turn on
to a 100% level or operate from paired
wallstations and occupancy sensor
controls.
Remove Unassigned
Devices
Pair Press and hold for 4
seconds recommended
(>2 sec. to <=10 sec.)
802.15.4 LED flashes rapidly (.25 sec
ON/.25 sec OFF) when the button is held
for the allotted time and continues until
the devices have been commanded to
leave the network.
802.15.4 LED will turn ON steady once
there are no devices remaining in the
Construction Area.
Devices still in the default construction
area will leave the WaveLinx network.
Reboot/Soft Reset Reset (Inset
Button)
Press and release (1
second)
All LEDs turn OFF after button release.
As device reboots, LEDs may turn ON and
OFF during reboot.
Once reboot completes (approximately 1
minute), Power/Health LED and 802.15.4
LED should be ON steady. Other LEDs
may also be on dependent on WAC2
configuration.
Devices will remain in previous
commanded state during reboot, rejoin
the WAC2 upon reboot completion and
continue their normal behavior.
Programmed settings are retained during
a reboot.
Authentication and Wi-Fi
Configuration Reset
Reset (Inset
Button)
Press and hold for 4
seconds recommended
(>2 sec. to <= 5 sec.)
Wi-Fi LED flashes rapidly (.25 sec ON/.75
sec OFF) when the button is held for the
allotted time.
Wi-Fi LED turns OFF for 1 second when
button is released and then blinks .5sec
ON/ .5 sec OFF for 5 seconds while the
WAC2 clears the settings.
Wi-Fi LED turns ON steady when process
is complete.
No effect on devices. The following data
will be cleared and reset to factory
defaults:
• Wi-Fi Access Point settings
• Wi-Fi Client settings
• Admin password
Reset factory defaults Reset (Inset
Button)
Press and hold for 8
seconds recommended
(>5 sec. to <=10 sec.)
The Wi-Fi LED starts flashing after 2
seconds.
All the LEDs except for BT will flash (.5
seconds ON/ .5 seconds OFF) when the
button is held for the allotted time.
The Power/Health LED will turn OFF when
the button is released,
and other LEDs will
stop flashing.
After a short delay, additional LEDs may
turn OFF and the WAC will reboot.
Once reboot completes (approximately 1
minute), Power/Health LED and 802.15.4
LED, and the Wi-Fi LED should be ON
steady. Other LEDs may also be on
dependent on connections.
All programming will be cleared for the
Wireless Area Controller and reset to
factory defaults including:
• Removing all 802.15.4 device pairing
• All user accounts
• Clearing user-uploaded custom
certificates
• Network configuration including:
• Wi-Fi client settings
• Wi-Fi access point settings
• Ethernet settings
• Clearing all programming including
area and zone designations
• Resetting WAC name to default