Programming Manual

132
WaveLinx User Manual
www.eaton.com/wavelinx
WaveLinx Industrial Integrated
Sensor
(Note that for high mount
applications, it may be difficult
to see the LED.)
No LED in the sensor window
and the connected fixture is
OFF.
• Verify that the fixture’s power source is connected and powered from the circuit breaker.
• Verify that the sensor is fully seated on the fixture mounting.
• Contact technical support for further assistance.
No LED in the sensor window
and the connected fixture is
ON.
• Try to perform the PAIR function. If the PAIR operation works, the LED may be turned off via a
software setting. Once the device is paired and accessible in the mobile application, select the
device to review the occupancy sensor settings and ensure that the LED function is enabled.
• If the PAIR function fails to find the fixture/sensor, contact technical support.
LED in the sensor window
blinks white instead of green.
• The sensor has been previously paired with a Wireless Area Controller. If there is more than
one Wireless Area Controller at the facility, identify which Wireless Area Controller is paired by
successively placing the Wireless Area Controllers into PAIR mode to locate which unit prompts a
dimming response in the load in question. Then, use the mobile application to identify and delete
the device manually from the incorrectly paired Wireless Area Controller. The device’s LED should
then blink green indicating its ready state for pairing.
WaveLinx Outdoor Integrated
Sensor
(Note that for high mount
applications, it may be difficult
to see the LED.)
No LED in the sensor window
and the connected fixture is
OFF.
• During daytime hours, the sensor may have lighting turned OFF due to out-of-the-box ON at dusk,
OFF at dawn operation. Verify operation after dusk.
• Verify that the fixture’s power source is connected and powered from the circuit breaker.
• Verify that the sensor is fully seated on the fixture mounting.
• Contact technical support for further assistance.
No LED in the sensor window
and the connected fixture is
ON.
• Try to perform the PAIR function. If the PAIR operation works, the LED may be turned off via a
software setting. Once the device is paired and accessible in the mobile application, select the
device to review the occupancy sensor settings and ensure that the LED function is enabled.
• If the PAIR function fails to find the fixture/sensor, contact technical support.
LED in the sensor window
blinks white instead of green.
• The sensor has been previously paired with a Wireless Area Controller. If there is more than
one Wireless Area Controller at the facility, identify which Wireless Area Controller is paired by
successively placing the Wireless Area Controllers into PAIR mode to locate which unit prompts a
dimming response in the load in question. Then, use the mobile application to identify and delete
the device manually from the incorrectly paired Wireless Area Controller. The device’s LED should
then blink green indicating its ready state for pairing.
WaveLinx Ceiling Sensor
LED does not flash
• Ensure that the sensor batteries are installed and charged.
WaveLinx Wireless Outdoor
Lighting Control Module
Connected load is OFF or ON
continuously.
• This device will operate the connected fixture via the onboard daylight sensor until the device is
paired with a Wireless Area Controller. To verify functionality, power down, then power up the
device via the circuit breaker. Immediately after power up, verify that the lighting load turns ON to
100% initially. The daylight sensor will then dictate whether the load remains ON or turns OFF.
• If load does not turn on initially upon power up, verify all connections and ensure the module is
properly seated in the fixture’s onboard mounting receptacle.
• Contact technical support if the problem persists.
WaveLinx Wallstation
standard line voltage powered
All the button LEDs are flashing
quickly.
• The wallstation is still in pairing mode and is indicating a successful connection to a Wireless
Area Controller. The wallstation will automatically time-out from this function after 1 hour.
• If the Wireless Area Controller has exited PAIR mode already, the press of the wallstation button
should also cancel the LED flash behavior.
When a button is pressed, no
LEDs illuminate.
• Verify that the circuit wiring is properly connected and energized.
• Contact technical support if the problem persists.
When a button is pressed
the LED flashes slowly for 10
seconds.
• The wallstation has not been paired with a Wireless Area Controller. Press the PAIR button on the
wireless area to reinitialize the PAIR process, then press the button on the wallstation again to
reissue the join request (the button LED will flash slowly for 10 seconds again to indicate the join
request will be sent. As it joins the network, the LED may flash very rapidly for approximately 5
seconds, then flash all LEDs to indicate it is paired).
• If the problem persists, verify that the distance of the wallstation to the controller is within the
expected range and that there are fewer than 200 devices paired before contacting technical
support.
When the button is pressed, the
LED stays ON.
• The wallstation has been previously paired and is part of either a construction group or mobile
application defined area. If paired with the incorrect Wireless Area Controller, locate the
controller that is responding to the button presses. Then, use the mobile application to identify
and delete the device manually from the incorrectly paired Wireless Area Controller to allow
pairing to the correct controller.