Programming Manual

15
WaveLinx User Manual
www.eaton.com/wavelinx
Device Successfully Paired Behavior (during initial pairing)
WaveLinx Wireless Dimming Switchpack
(WSP-MV-010: 120-277VAC model)
Connected 0-10V dimmable fixtures dim to 10%.
WaveLinx Wireless Dimming Switchpack
(WSP-CA-010: 120-347VAC model)
Fixture dims briefly when paired then turns ON to a brighter light level and remains ON.
It may be difficult to review paired behavior during the initial pairing cycle. Pairing can be verified after PAIR
mode exits (see chart that follows this section).
WaveLinx Integrated Sensor Fixture dims to 10%.
LED in sensor window should blink WHITE with motion detection.
WaveLinx Industrial Integrated Sensor Fixture dims to 10%.
LED in sensor window should blink WHITE with motion detection.
WaveLinx Outdoor Integrated Sensor Fixture dims to 10%.
LED in sensor window should blink WHITE with motion detection.
WaveLinx Tilemounted Sensor Connected 0-10V dimmable fixtures dim to 10%.
LED in sensor window should blink WHITE with motion detection.
WaveLinx Ceiling Sensor There is no immediate feedback that pairing was successful. Pairing will be verified through the mobile
application in a later step.
WaveLinx Wireless Outdoor Lighting Control Module Fixture dims briefly when paired then turns ON to a brighter light level and remains ON.
It may be difficult to review paired behavior during the initial pairing cycle. Pairing can be verified after PAIR
mode exits (see chart that follows this section.)
WaveLinx Wallstation
standard line voltage powered
Once successfully paired, all button LEDs will flash in a top to bottom the bottom to top pattern until pairing
mode is exited.
WaveLinx Battery Powered Wallstation There is no immediate feedback that pairing was successful. Pairing will be verified through the mobile
application in a later step.
WaveLinx Receptacle During pairing, the outlet LED may flash red or may flash green to amber. The outlet may turn OFF for a period
of time and then turn back ON. The duration of the OFF period may vary but should not last longer than 5
minutes.
It may be difficult to review paired behavior during the initial pairing cycle. Pairing can be verified after PAIR
mode exits (see chart that follows this section).
5: Either allow the pairing mode’s 60 minute automatic time-out period to expire, or if all devices appear to have paired successfully,
manually cancel pairing mode. To manually cancel pairing mode, if the Wireless Area Controller’s blue 802.15.4 LED is still flashing, press and
release the PAIR button (1 second press) to exit pairing mode. (If PAIR mode has already exited automatically, the blue 802.15.4 LED will be
ON continuously.)
6: If not confirmed during the initial pairing process, verify devices paired with the Wireless Area Controller successfully. The chart below
describes how to verify that items have paired after exiting the initial pairing mode. All devices in the default construction area should exhibit
the behavior shown below.
Device Method 1: Press the PAIR mode button on the
Wireless Area Controller to place the controller
in PAIR mode again.
Method 2: Verify by method described below
WaveLinx Wireless Dimming Switchpack
(WSP-MV-010: 120-277VAC model)
Paired device behavior:
Connected 0-10V dimmable fixtures dim to 10%.
WaveLinx Wireless Dimming Switchpack
(WSP-CA-010: 120-347VAC model)
Paired device behavior:
Connected 0-10V dimmable fixtures dim to 10%.
WaveLinx Integrated Sensor Paired device behavior:
Fixture dims to 10%.
LED in sensor window should blink WHITE with motion
detection.
WaveLinx Industrial Integrated Sensor Paired device behavior:
Fixture dims to 10%.
LED in sensor window should blink WHITE with motion
detection.
WaveLinx Outdoor Integrated Sensor Paired device behavior:
Fixture dims to 10%.
LED in sensor window should blink WHITE with motion
detection.