Installation Instructions

FCC
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off an on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
This equipment must be installed and operated
in accordance with provided instructions and
the antenna(s) used for this transmitter must be
installed to provide a separation distance of at least
20 cm from all persons.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
CAUTION!
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
Bluetooth
The Bluetooth
®
word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Eaton is under license. Other
trademarks and trade names are those of their
respective owners.
Industry Canada
This device complies with Industry Canada’s licence-
exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR
d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le
fonctionnement.
The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can
obtain Canadian information on RF exposure and
compliance.
Le dispositif rencontre l’exemption des limites
courantes d’évaluation dans la section 2.5 de RSS
102 et la conformité à l’exposition de RSS-102 rf,
utilisateurs peut obtenir l’information canadienne
sur l’exposition et la conformité de rf.
This transmitter must not be co-located or
operating in conjunction with any other antenna
or transmitter. This equipment should be installed
and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne
fonctionnant en même temps qu’aucune autre
antenne ou émetteur. Cet équipement devrait être
installé et actionné avec une distance minimum de
20 centimètres entre le radiateur et votre corps.
2-Year Limited Warranty
THE FOLLOWING WARRANTY IS EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES, WHETHER
EXPRESS, IMPLIED OR STATUTORY INCLUDING,
BUT NOT LIMITED TO, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period
of two years from the date of purchase, Eaton
products will be free from defects in materials and
workmanship. The obligation of Eaton under this
warranty is expressly limited to the provision of
replacement products. This warranty is extended
only to the original purchaser of the product. A
purchaser’s receipt or other proof of date of original
purchase acceptable to Eaton. This is required
before warranty performance shall be rendered.
This warranty does not apply to Eaton products
that have been altered or repaired that have been
subjected to neglect, abuse, misuse or accident
(including shipping damages). This warranty does
not apply to products not manufactured by Eaton
which have been supplied, installed, and/or used
in conjunction with Eaton products. Damage to the
product caused by replacement bulbs or corrosion
or discoloration of brass components are not
covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES (REGARDLESS OF
THE FORM OF ACTION, WHETHER IN CONTRACT,
STRICT LIABILITY, OR IN TORT INCLUDING
NEGLIGENCE), NOR FOR LOST PROFITS; NOR
SHALL THE LIABILITY OF EATON FOR ANY CLAIMS
OR DAMAGE ARISING OUT OF OR CONNECTED
WITH THESE TERMS OR THE MANUFACTURE,
SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF EATON PRODUCTS, OR SUPPLY
OF ANY REPLACEMENT PARTS THEREFORE,
EXCEED THE PURCHASE PRICE OF EATON
PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR
INSTALL FIXTURES.
To obtain warranty service, please contact Eaton,
at 1-800-334-6871, press option 2 for Customer
Service, or via e-mail ConsumerProducts@eaton.
com and include the following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a
Return Goods Authorization Number issued by the
Company and must be returned freight prepaid.
Any product received without a Return Goods
Authorization Number from the Company will be
refused. Eaton is not responsible for merchandise
damaged in transit. Repaired or replaced products
shall be subject to the terms of this warranty and
are inspected when packed. Evident or concealed
damage that is made in transit should be reported
at once to the carrier making the delivery and
a claim filed with them. Reproductions of this
document without prior written approval of Eaton
are strictly prohibited.
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.