ALARM SYSTEM USER GUIDE Issue 2
Contents Compliance Statements .............. iii 1. Introduction ................................ 1 Alarm System ............................... 1 Keypad ......................................... 2 Proximity Tags ............................. 2 Mains Power Failures ................... 4 About this Guide........................... 4 2. Everyday Operation ................... 5 Setting the System ....................... 5 General Procedure ................... 6 Timed Set .................................
Compliance Statements The 9651PD control unit is compliant with EN50130-5 environmental class II. The 9651PD control unit is suitable for use in systems designed to comply with PD 6662: 2010 at Grade 2. The 9941 and 9943 keypads are suitable for use in systems designed to comply with PD 6662;2010 at Grade 2. If the installer selects a non-compliant configuration then they must remove or adjust compliance labelling There are no user serviceable parts within the keypads or the control unit.
This page is deliberately blank.
1. Introduction Alarm System The alarm systems described in this book comprise a control unit (model 9651PD), one or more keypads, and various detectors. The control unit houses a main controller, power supply, stand-by battery and communication device. It is normally fitted in a safe place out of sight (for example, under the stairs). The detectors are installed in various places, or zones, around the premises. If something triggers a detector, the detector signals this to the control unit.
1. Introduction Keypad Your alarm system is fitted with a 9941 or 9943 keypad, from which you can set and unset the system. Figure 1 shows the main features of the keypad. Refer to "4. Special Functions" on page 12 for information about other functions available from the keypad. The system will not accept commands from the keypad until you identify yourself with either an access code or a proximity tag (see below). The system can store 50, four-digit, access codes, giving secure access for up to 50 users.
1. Introduction These may show nothing until a user is identified. Alert lamp (see page 12) Flashes to highlight unacknowledged alarm, fault or tamper conditions. Glows for acknowledged conditions. Goes out when all conditions are rectified. Service lamp Glows if the system needs an Installer reset. Mains lamp Glows when using mains power. Flashes when using stand-by battery. 2-line 16-digit liquid crystal display The first line shows: - unset: time and date - set: level set.
1. Introduction Mains Power Failures The control unit indicates mains power failures using alerts. If the supply has since been restored, the alert will show the condition as inactive. For instructions on how to view and acknowledge alerts, refer to page 12. About this Guide The rest of this guide tells you how to use the system: 2. Everyday Operation Tells you how to set and unset the system. 3.
2. Everyday Operation During installation, your installer programs the system to create an exit route and entry route for your premises. When setting the system, you must follow the exit route. When unsetting the system, you must follow the entry route. If you stray from these routes, you may cause a false alarm. Setting the System There are several different methods for setting the system. Each level can use a different method, although not all methods are available in all cases.
2. Everyday Operation General Procedure To set the system: 1. Secure all doors and windows. 2. At the keypad, key in an access code (or present a tag). Note:If you enter an incorrect code, try again. If you enter an incorrect code four times, all keypads will be locked for 90 seconds and a tamper alarm will start. The display shows (for example): 3. System OK Set? Press the appropriate level key. Note: If you press without a level key, the system sets Level A (Full Set). 4. 5.
2. Everyday Operation Timed Set With Timed Set, the system sets after a programmed exit time has expired. The time starts when you press a level key, or when you press to accept an omitted zone. Your installer will have made the exit time long enough for you 3 to leave the premises and secure the final door . Final Door Set Your installer may have programmed the system so that closing the final door 4 completes the setting sequence. The system sets 7–12 seconds after you secure the final door.
2. Everyday Operation Investigating Setting Problems This section offers general guidance but the configurable nature of 9651PD control units means that details of each alert and response vary. If you need assistance to resolve a problem, contact your installer. Detector Active If something is triggering a detector at the end of the exit procedure, the system will not set. The display shows which zone (or zones) is active. To set the system: 1. 2. 3. 4. 5.
2. Everyday Operation call an installer to do this for you (see page 11). If the display shows "Set" underneath the alert message, press to continue with setting. If an installer reset is required, the control unit lights the lamp and the keypad sounds a repeating "beep" to warn you. If the fault disappears, the lamp goes out but the tone continues until you enter your access code. If the fault persists and cannot be overridden, the display shows "Call Installer".
2. Everyday Operation Unsetting the System WARNING: If you enter your premises and an internal alarm starts, there may be an intruder. You must unset the system from a keypad. When you open an entry door, the system starts an entry timer. During the entry time, the keypads give a "galloping" entry tone to warn you that the timer is running. If you exceed the entry time, an alarm will occur.
3. After an Alarm Responding to a Fire Alarm IMPORTANT: The system gives a fire alarm by sounding a two-tone warning from the keypads and alarm sounder. The display shows (for example): 1. Evacuate the premises. Do not attempt to unset the alarm. 2. If there is evidence of fire, call the Fire Brigade. 3. Only when the premises are safe, proceed as for other alarms.
4.
4. Special Functions The display shows the first alert (for example): 3. 4. Here, "Inactive" indicates that the mains power supply has since been restored. Press for "Next" to view the next alert. The display shows the second alert (for example): Here, "Inactive" indicates that the tamper switch has since been closed. Press for "Next" to view the next alert.
4. Special Functions 3. 4. Press the number of the zone you want to omit (for example, press 07 to omit zone 7) and then press . The sounder gives a double "beep" and the display shows the zone number followed by an "o": If you try to omit a zone for which this is not allowed, the display shows an "X" after the zone number. Press to exit. Omit Zone 07o Omit Zone 07X Note: To include a zone that was omitted, follow the same procedure. Pressing toggles between omit and include.
4. Special Functions Key 4: To Change an Access Code Note: Cooper Security advise you to ensure that each user has their own access code, and no one user (including the master user) knows any other user’s access code. 1. Key in the access code that you wish to change. 2. Press 4. The display shows the user number and any text description for that user, for example: U23:User 23 If you wish to change the name, use the keypad as described in Changing User Names on page 19. Go to step 4.
4. Special Functions In the log, user codes are represented by numbers as follows: U00 U01 U02 to U49/50 U52 U53 U56 Installer User 1 Users 2 to 49/50 Control unit Idle Remote reset Key 7: Turning the Chime On and Off Your system may be programmed so that a chime tone sounds when certain doors are opened while the system is unset. You can turn this on and off. 1. Key in an access code (or present a tag). 2. Press 7 to toggle chime on and off.
4. Special Functions Key 9: Testing Detectors You can set the system so that it will allow you to walk around and test each of the detectors (a walk test). Do this when the premises are empty to avoid other people triggering movement detectors before you do, which would confuse the results of the test. If a detector fails the test, contact your alarm company and ask them to check the system. Notes: 1. 2. You can abandon the test at any time by pressing .
4. Special Functions The default access code for all users U02 through to U50 is “0000”. As default codes cannot be used to set or unset the system, or use any of its special functions, they do not need to be changed until they are assigned to users. Note: Once a master user assigns a code to another user, they must instruct the user to change their code straight away to something that the master user does not know.
4. Special Functions 5. If you wish to change the name, use the keypad as described in Changing User Names on page 19. Go to step 6. If you do not want to change the name, then press . The display shows (for example): 6. Key in the new access code. The display shows (for example): 7. Press to store the new access code (in this case, 4926). To Delete a User: 1. Key in the master user access code. 2. User 21: ---- User 21 = 4926 System OK Set ? Press 4. The display shows: Old Code= 3.
4. Special Functions 1 2 3 4 5 6 None ABCÆÅÄ DEF GHI JKL MNOØÖ 7 8 9 0 C D PQRS TUV WXYZ Space ' ( ) : . - ! & Move right Move left To delete a whole name, move to the first character and press D. When you have entered the name, press to continue with setting the code. Proximity Tags Each normal user (Users 02 to 50) can have a tag, an access code or both. You cannot assign a tag to the master user (U01) or the installer (U00). To Assign a Tag To a User: 1. Key in the master user access code. 2.
4. Special Functions The keypad gives a double beep confirmation tone and then displays the time and date: To Delete a User With A Tag Note: To delete a proximity tag from the system, you must delete the user (set their access code to “0000”). 1. Key in the master user access code. System OK Set ? 2. 3. 4. 5. Press 4. The display shows: Old Code= EITHER: Key in “001” and then press . Press repeatedly until the display shows the user number of the code you want to delete: U01: User 01 Press .
4. Special Functions Key 6: Setting Time and Date Note: Only the master user (U01) can set the system time and date. The control unit contains an internal clock/calendar that runs as long as there is power present (mains or stand-by battery). The system uses this clock to record the time and date of events in the log. If the mains power supply fails while the stand-by battery is low, you may need to correct the time and date. If your country uses summer and winter time, you may need to adjust the time.
Appendix.
Appendix Message Meaning Technical alarm in zone == Technical alarm in zone Tech Z== Rstr == reset Line fault on telephone Tel Line Fault line Line fault reset on Tel Line Rstr telephone line Telecmd Low Bat Low battery in 723r telecommand Panic (Hold Up) alarm Telecmmd PA from 723r telecommand U== Change U== User == changed access code for user == User == deleted access U== Delete U== code for user == Installer exited from U== Off-Site programming mode Installer entered from U== On-Site programming mode
NOTES: Page 25
NOTES: Page 26
NOTES: Page 27
Your Installation Zone 1 2 3 4 5 6 7 8 Company Name Control Unit Model Exit Time Bell Duration Communicator Fitted Description A A Contact Number (Day) Contact Number (Night) B C Entry time B C D Omit Chime Allow D Note: If this table has not been completed, ask your Installer for the information.
