i-on160EX Security System Administrator’s and User Guide
© Cooper Security Ltd. 2010 Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book are subject to change without notice. Printed and published in the U.K Part Number 12019971 5/11/10 Warning: Mains voltages are present inside control unit. No user serviceable parts inside.
Contents 1. Introduction .............................................................1 Setting and Unsetting .................................................. 3 Alarms and Reset ............................................................... 3 Security Levels .................................................................. 3 Partitions .......................................................................... 3 24 Hour Alarms..................................................................
Users .......................................................................34 Editing Existing Users ....................................................... 35 Adding Users ................................................................... 47 Deleting Users ................................................................. 50 Viewing the Log ........................................................51 Testing the System ....................................................52 Sirens & Sounders ............
i-on160 Compliance Statement The i-on160EX is suitable for use in systems designed to comply with PD6662:2004 at Grade 2, Grade 3 and environmental class II. The i-on160EX is suitable for use in systems designed to comply with the requirements of EN50131-3 at Grade 2, Grade3 and environmental class II. This product complies with the requirements of EN50131-6:2008 at Grade 2, Grade 3 and environmental class II.
i-on160 This page is intentionally blank.
i-on160 1. Introduction The i-on160EX is an intruder alarm system intended mainly for use in commercial properties. The heart of the i-on160EX system is the control unit, its expanders and keypads. The control unit contains the main processing unit, the power supply and stand-by battery. The stand-by battery can keep the alarm system going for a few hours if the mains supply fails. Connected to the control unit by cable are the expanders and keypads.
1. Introduction i-on160 1 2 3 A B 1. Two button panic alarm with tilt switch. 4 5 2. Two button panic alarm. 3. Four button remote control. 4. Keypad A 1 2 abc 3 def A 1 2 abc B 4 ghi 5 jkl 6 mno B 4 ghi 5 jkl 6 mno C 7 pqrs 8 tuv 9 wxyz C 7 pqrs 8 tuv 9 wxyz D * 0 # D * 0 # 5. Wireless arming station. 6. Door Contact/Universal Transmitter. 6 7 7. Smoke Detector. 10. Passive Infra Red. 11. External siren/strobe. 9 Figure 1.
i-on160 1. Introduction Setting and Unsetting The majority of alarm systems are intended to detect the movements of people, and to notify others when people move into protected areas. Readying the system to start an alarm when someone moves into a protected area is called “setting” the system. Disarming the system so that people can move freely is called “unsetting” the system.
1. Introduction i-on160 The i-on160EX can have up to 20 partitions. Users can set and unset each partition completely independently of all the others. Individual users can be given access to one or more partitions: if they have no access to a partition then they cannot set or unset that partition. In effect the i-on160EX becomes 20 separate alarm systems. In addition each partition can be programmed to set at one of two security levels: either Full Set or Part Set B.
i-on160 1. Introduction Controls and Displays Figure 2 shows the controls and displays available on the keypad. 1. LCD display . 1 2. Programming keys. 2 7 3 4 5 A 1 2 abc 3 def B 4 ghi 5 jkl 6 mno C 7 pqrs 8 tuv 9 wxyz D * 0 # 6 3. Navigation key 4. Setting and unsetting keys. 5. Panic Alarm (PA) keys. 6. Alpha/numeric keys. 7. Set/Unset status LEDs (not used in partitioned systems). Figure 2. Controls and Displays Controls: A Full Sets the system. (All detectors in use.
1. Introduction i-on160 b) Press this key to abandon your decision when the display shows “Are you sure Y/N?” Press this key to gain access to the Menu. 1 to 0, Used to key in access codes. Can also be used to key in *, # text for names, and telephone numbers. # Used when keying in text: press to change between capitals or small letters. Press both these keys at the same time to start a Panic Alarm. (The Installer must enable this feature.
i-on160 1. Introduction Note that the installer can disable these LEDs in order to hide the state of the system (to comply with EN50131). In addition, in a Security Grade 2 installation the installer may have programmed the LEDs to glow for 30s immediately after setting, and then to go out. Detectors or Zones? When talking about alarm systems, people tend to use the words “detectors” and “zones” interchangeably. Most of the time this doesn’t matter, but occasionally it can cause some confusion.
1. Introduction i-on160 Normal User A normal user is assigned to one or more partitions. They cannot add or delete other users. A normal user can change their own access code, switch the Chime function on and off, and operate any outputs that the installer has made available. Normal users can set and unset their partitions at any time. Guard A guard can only unset a partition in alarm, reset it, and then set the partition again. A guard cannot change their access code.
i-on160 1. Introduction Access to the System To operate the system a user must identify themselves, either by entering an access code on the keypad or by presenting a proximity tag to the front of the keypad (see page 10). Access code and proximity tag act as unique identifiers for each user, and may be used interchangeably at any time. Access Codes In a Security Grade 2 system access codes are four digits long, providing a total of 10,000 different codes, running from “0000” to “9999”.
1. Introduction i-on160 Proximity Tags A proximity tag is a small plastic token with a low powered radio transmitter inside. Each tag contains a unique identity code. (There are 4,294,967,296 (232) different tag identity codes.) Inside the keypad is a sensor. When you present the tag within about 10mm of the front of the keypad, the control unit senses the presence of the tag and reads its identity code.
i-on160 1. Introduction 1. 2. 3. 4. 5. Full Set. Part Set. Not used. Unset. Transmit LED. A B Figure 3. Remote control Buttons. Each remote control has a unique electronic identity. When you assign a remote control to a user you teach the identity to the control unit. You may assign one (and only one) remote control to each user. Panic Alarms (PA) A PA is a two button transmitter, used to start a Panic Alarm. To activate the transmitter you must press both buttons at the same time.
i-on160 2. Alarms The table below shows the different kinds of alarms possible. Type of Alarm Intruder Signal (see note) Started by: Loud warbling tone from siren. Normal alarm or entry route zone activated when system is set. Fire Pulsing tone from siren. Fire zone activated at any time. Panic Loud warbling tone from siren PA zone or Panic Alarm transmitter activated at any time. 24 hour zone activated at any time. Pressed on keypad. (The installer must enable this feature on your system.
i-on160 1. Make sure it is safe to enter the premises: 2. Either key in your access code OR present your proximity tag. 2. Alarms Enter Access Code (** ) Press tick to reset Burg Z040 Alarm The bottom line of the display shows the first zone to alarm. 3. 4. Press < or > to see the name of the zone (if the installer has programmed one), for example: Press Y to reset the system. The system returns to standby, and is ready to set again. (The top line may show the installer’s name.
2 Alarms Press < or > to see the name of the zone (if the installer has programmed one), for example: Press Y to restore the display to normal. i-on160 Press tick to Reset Hallway i-on160EX 12:20 02/11/2010 If you wish to see any other zones that were triggered during the alarm, look in the log (see page 51). If You Cannot Reset the System Your system may be programmed so that it has to be reset by an installer after an alarm.
i-on160 2. Alarms When you talk to the alarm company, they will ask about the circumstances of the alarm, and also for the code you recorded from the display. If the alarm company decides that an engineer does not need to visit you, then they will give you another four digit code (the “anti-code”). Key in the anti-code at the keypad. The system will reset, and you can carry on using it as before. Accidental Alarms If you set off an alarm accidentally, you have 90 seconds to cancel the alarm.
2 Alarms i-on160 Function Key End this call (and let the control unit contact the ‘5’ other destinations for this alarm) Play ‘Home’ and ‘alarm’ message again ‘3’ Clear down (and do not call any of the other ‘9’ destinations for this alarm). Note: When the called party answers a speech dialler call there is a six second delay before the control unit starts playing the home message. Alerts (or Why is it Beeping?) From time to time the control unit may detect that there is a problem with the system.
i-on160 2. Alarms alerts the keypad will return to its’ standby screen and, after a few seconds, the rim of the navigation pad will glow green. In addition the keypad will stop beeping. OR: Press X. The rim of the navigation pad will stay red and the system will show the text of the alert the next time you key in an access code. (The keypad will stop beeping.) Note: 1. The system will not alert you to short (less than 10s) interruptions of mains power.
2 Alarms i-on160 “RESET FAULTS”. You must make sure that the detector is not active before you can reset a technical alarm.
i-on160 3. Setting and Unsetting Setting the System Using a Keypad Do this: 1. Make sure the system is idle. Secure all the windows and doors. The display shows: 12:20 i-on160EX 02/11/2009 (The top line may show the installer’s name.) 2. Either key in your access code. Enter Access Code (** ) As you key in your code the display shows a “*” for each digit. OR present your tag. The bottom line of the display shows each item from the rest of the menu in turn 3.
3. Setting and Unsetting i-on160 keypad sounds the exit tone (a continuous tone). The top line of the display shows the part of the system being set, the bottom line shows the remaining exit time (in seconds). 5. Leave by the designated exit door. 6. At the end of the exit time the system sets. System Set followed by: 12:20 i-on160EX 02/11/2010 Note: if you want to stop setting then press (unset key). In a part set system, one of four LEDs glows to show which part of the system is set.
i-on160 Do this: 1. Make sure the system is idle. Secure all windows and doors. 3. Setting and Unsetting The display shows: 12:20 i-on160EX 11/09/2010 (The top line may show the installer’s name instead of “ion160EX”.) 2. Press A, B, C or D. The keypad sounds the exit tone (a continuous tone). The top line of the display shows the part of the system being set, the bottom line shows the remaining exit time (in seconds). 3. Leave by the designated exit door. 4.
3. Setting and Unsetting i-on160 Unsetting the System Using a Keypad When unsetting the system do not stray from the entry route designated by the installer. If you do so then you will cause an alarm. Do this: 1. Enter by the designated entry door or route. Go directly to the keypad. The display shows: 12:20 i-on160EX 11/09/2010 The keypad sounds the entry tone (an interrupted tone). The system starts the entry timer. 2.
i-on160 3. Setting and Unsetting being monitored. If there is any activity on any detector then the system will start an alarm. “Part Set” means that the system is monitoring some detectors but not others. The installer selects those detectors that should be monitored during a Part Set. “Partition” is a segment of the whole system that may not be accessible to some users. Some users can only set a single Partition. Other users may be able to set two, three or more Partitions.
3. Setting and Unsetting i-on160 access code or tag the system unsets that partition. 3. Press u or n to show “Partitions”. “Partitions” is the second or third item down on the setting options menu. 4. Press Y. The bottom line of the display shows the possible states of the first partition: ↕ Setting Options Partitions > Partitions: Partition 1 U U>P ↕ U = Unset S = Full Set P = Part Set “U>P” = change to Part Set. “U>S” = change to Full Set.
i-on160 3. Setting and Unsetting access. Partitions you have chosen to unset, unset immediately. Partitions you have chosen to set start their exit timer (or set immediately - see note.). Note: If a partition is programmed to set instantly make sure you are outside the protected area before pressing Y. The keypad sounds the exit tone (a continuous tone). The top line of the display shows the part of the system being set, the bottom line shows the remaining exit time (in seconds). 9.
3. Setting and Unsetting i-on160 If the System Will Not Set Normally, the system will set only when all the detectors are “quiet”, that is: not reporting any activity. If you have the final exit door open, or if you trigger one of the detectors on your exit route, then the keypad and internal sounder will give an interrupted setting tone (this is normal). Make sure that you close all the doors on your exit route and the final exit door as you leave.
i-on160 3. Setting and Unsetting The table below shows the keypad message for each fault, what the message means, and who can override the fault in either a Security Grade 2 or Grade 3 system. Override by: Message Meaning Panic A PA device is still active Installer Installer TAMPER A part of the system has Installer Installer been tampered with. Missing An expander or keypad Installer Installer has a fault, or the cabling between parts of the system has a fault.
3. Setting and Unsetting i-on160 (If you wish to stop setting while the exit tone sounds, then press .) The left hand LED glows to show that the keypad is transmitting. 3. Leave by the exit door and make sure that it is closed properly. Unsetting 1. Enter by the designated entry door. 2. Key in a valid access code. 3. Press . Silencing an Alarm 1. Key in a valid access code. 2. Press .
i-on160 3. Setting and Unsetting Note: The radio keypad does not show the status of the alarm system at all. The left hand “Transmit” LED glows only to show that the keypad is sending a command to the control unit. Using a Remote Control Setting Note: You must ask your Administrator to provide a suitably programmed remote control, see i-on40 Administrator’s Guide. Secure all your windows and doors. Make sure the system is idle, and that you can hear the warning tones from the sounders. 1.
3. Setting and Unsetting i-on160 Unsetting 1. Enter by the designated entry door. 2. Press on your remote control. The system unsets. At this point the system displays the standby screen. If The System Will Not Set by Remote Control If one of the detectors is still active when you try to set the system then you will not hear the exit warning tone. What happens next depends on how the installer has set up your system. a) Try pressing A once more on your remote control.
i-on160 4. Administration To make changes to the way your system works you must enter the Menu. Your degree of access to the Menu depends on what type of user you are: Master User, Admin User or Normal User. A Master User has access to all the options of the Menu. A Master User can add, change, or remove users in any partition, and has full access to the system options menu. An Admin user may be limited in the partitions that they can access.
4. Administration i-on160 (If you do not press any keys on the keypad for 60 seconds then the display returns to the standby screen.) The rest of this chapter describes each of the main options in the Menu. Editing Text For many of the items that you can program, the control unit lets you assign a 12 character name.
i-on160 4. Administration Omitting Zones You may wish to prevent a zone causing an alarm. For example, if your garage door is protected by a detector, but you wish to leave it unlocked for the delivery of a parcel, you may wish to omit that detector when you set the rest of the alarm system. Provided that the Installer has programmed your system to allow this, then, to "Omit" a zone. 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). 4.
4. Administration 7. Repeat steps 5 and 6 for any other zone you wish to omit (or include). 8. Press Y to store the changes you have made. 9. Press X to leave the Menu. i-on160 MENU Omit Zones 12:20 > i-on160EX 02/11/2010 The control unit allows you to omit a zone for one setting/unsetting cycle. You will have to omit the zone again for the next setting/unsetting cycle. Users The control unit can recognise up to 500 individual users.
i-on160 4. Administration A Normal or Partition User can: Edit their own user code, and delete or add their own proximity tag, remote or PA. Guards and Set Only users have no access to the Menu. Editing Existing Users This menu lets you change the details for an existing user. Name Use this option to give the user a 12 character name. 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n . MENU Users > 5.
4. Administration 9. Press Y . The bottom line shows: 10. Press Y. The display shows the current name given to the user, and places a cursor at the beginning of the name. i-on160 USER 003 Name > EDIT USER NAME User 003 11. Key in the name from the keypad. See Editing Text on page 32. EDIT USER NAME Arthu_ 12. Press Y when finished. Arthur Name The display will show the name in menus and in the log when the user sets, unsets or resets the system.
i-on160 4. Administration programmed into the control unit. In the example shown the name is “User 001”. 8. Press u or n to display the user you wish to edit. EDIT USER User 003 > USER 003 Name > (Alternatively, if you already know their user number, you can key that in and the display will show that user immediately.) 9. Press Y . The bottom line shows: 10. Press n . 11. Press Y. The bottom line of the display shows the current user type. See page 7 for a description of the user types available.
4. Administration i-on160 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n . MENU Users > 5. Press Y. USERS Add User > 6. Press n . USERS Edit User > 7. Press Y . EDIT USER User 001 > EDIT USER User 003 > USER 003 Name > 10. Press n until the display shows: USER 003 Partitions > 11. USER 003 Partition 1 USER 03 Partition 3 The bottom line of the display shows the first in a list of the users already programmed into the control unit. 8.
i-on160 4. Administration 13. Press > to change a “Yes” to a “No” or back again. USER 003 Partition 3 Yes See page 3 for a description of partitions. See Note below for a quick way of assigning users to partitions. 14. Press Y when you have finished assigning the user to their partitions. USER 003 Partitions > Note: By default new users belong to all partitions.
4. Administration i-on160 5. Press Y. USERS Add User > a) Press n. USERS Edit User > b) Press Y. EDIT USER User 001 > c) Press u or n. until the bottom line of the display shows your own user name. EDIT USER User 003 > d) Press Y. USER 003 Name > e) Press u or n. until the bottom line of the display shows: USER 003 Code > f) Go on to step 6. If you are a Normal User: 5 Press Y. 6. Press Y. 7. Key in the new access code . Access codes are four digits long.
i-on160 4. Administration Proximity Tags No user can change or delete any other user’s proximity tag. (A Master User or Admin User can register a proximity tag for a new user when they first add the user to the system, see page 47.) Any user except a Guard or Set Only user can register a tag for themselves as follows: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n . MENU Users > .
4. Administration 8. Press Y. Note: If you already have a prox tag allocated to you then the screen will display “Delete Prox Tag?”. See page 46. 9. Hold the prox tag up to the keypad. i-on160 Present Prox Tag to add to panel Prox Tag added followed by: The control unit learns the USER 002 identity of the tag and links it Prox Tag > with your access code. You cannot register more than one tag.
i-on160 4. Administration a) Press n. USERS Edit User > b) Press Y. EDIT USER User 001 > c) Press u or n. until the bottom line of the display shows your own user name. EDIT USER User0 03 > d) Press Y. USER 003 Name > e) Press u or n. until the bottom line of the display shows: USER 003 Remote > f) Go on to step 8. If you are a Normal User: 6. Press Y. USER 002 Code 7. Press n until the display shows: USER 002 Remote 8. Press Y.
4. Administration i-on160 If the control unit has already learned that remote control then you will hear a low tone and the display tells you that the remote control is already in use. If you do not wish to register a remote control press X. If you have a remote control and want to know who it belongs to then use the Test - Remotes menu option, see page 52 . Panic Alarms (PA) No user can change any other user’s PA.
i-on160 4. Administration d) Press Y. USER 003 Name > e) Press u or n. until the bottom line of the display shows: USER 003 Panic Alarm > f) Go on to step 8. If you are a Normal User: 6. Press Y. USER 002 Code 7. Press n until the display shows: USER 002 Panic Alarm 8. Press Y. The display asks you to press both of the buttons on the Panic Alarm.
4. Administration i-on160 Deleting Remote Controls, Tags and PAs If you have lost a remote control, prox tag or panic alarm assigned to you then you should delete it from the system to make sure that no unauthorised person can use it. 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n . MENU Users > . 12:20 i-on160EX 02/11/2010 Enter Access Code ( ) If you are a Master or Admin User: 5. Press Y.
i-on160 8. 4. Administration Press Y. The bottom line of the display asks if you wish to delete the device you selected. 9. Press Y The control unit deletes the identity of the Panic Alarm (or other device you selected). USER 002 Delete Panic Alarm? Panic Alarm deleted followed by: USER 002 Panic Alarm > To register a new device, re-enter the Menu and select Users - Edit User. Select your own user name and then the device type you wish to add.
4. Administration 6. Press Y. The display shows a default user name, for example: “User 004”. Edit the name (for hints on editing text see page 32). 7. Press Y when you have finished editing the name. i-on160 Name : User 004 User 004 Normal User The display shows the default type for a new user (Normal User, see page 7 for a description of user types). 8. Press u or n to show the type you want to assign to the new user and then press Y.
i-on160 c) Press Y when you have finished assigning the user to their partitions. The display asks you to assign a new user code. 9. 4. Administration Assign Access Code ( ) Key in the user code you want the new user to employ. ( If you do not want to assign a code to the user press Y.) The display asks you to confirm the new code. Confirm New Code ( ) 10. Key the code in a second time. The display asks you to present a proximity tag to the keypad. Present Prox Tag to add to panel 11.
4. Administration i-on160 for the user press Y. Followed by: The display should now tell you that the new user has been added to the system. USERS Add User > Deleting Users You must be a Master or Admin user to delete a user, see page 34. To delete a user: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n . MENU Users > 5. Press Y. USERS Add User > 6. Press n until you see: USERS Delete User > 7.
i-on160 4. Administration (If you change your mind at this point press X.) 10. Press Y to confirm that you wish to delete the user. DELETE USER User 001 > The control unit deletes the user from the system. Once you delete a user, the system does not respond to their access code or to their proximity tag. In addition, the control unit "forgets" the identity of all remote controls and PAs assigned to the user.
4. Administration i-on160 n shows earlier events, u shows more recent events. 8. Press X to finish viewing the log. MENU View Log > When you view the log, the display initially shows users by their number (for example User 001). Pressing > displays any name programmed for the user.
i-on160 5. Press Y. The display shows: 6. Press Y . The bottom line of the displays shows the first in a list of the siren types that you can test: 7. Press Y. If you have external radio sirens fitted to your system, you will see: If you do not have any external radio sirens fitted the keypad shows for a few seconds: a) Press >. The control unit turns on the external radio sirens. Check that you can hear them. 4. Administration TEST Sirens & Sounders > SIRENS & SOUNDERS Ext.
4. Administration i-on160 can hear them. b) Press > again to turn the sirens off. WIRED SIRENS All Sirens Off 11. Press Y when you have finished this test. SIRENS & SOUNDERS Wired Sirens > 12. Press n. SIRENS & SOUNDERS Loudspeakers > The display shows the next item in the list of tests. 13. Press Y. LOUDSPEAKERS Loudspeakers Off a) LOUDSPEAKERS Loudspeakers On LOUDSPEAKERS Loudspeakers Off Press >. The control unit sounds a test tone on the loudspeakers. Check that you can hear them.
i-on160 4. Administration finished this test. 18. Press X to leave the siren test menu. TEST Sirens & Sounders > Keypad 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n until you see:. MENU Test > 5. Press Y. TEST Sirens & Sounders > . The display shows: 12:20 i-on160EX 02/11/2010 Enter Access Code ( ) 6. Press n until you see: TEST Wired Keypad 7. Press Y.
4. Administration i-on160 Tick Key As you press the function keys on the keypad the display shows their name, for example: 9. Press X to end the test. TEST Wired Keypad > Walk test The Walk Test menu allows you to test detectors without starting an alarm. To “walk test” an alarm system you operate each detector in the system. If the detector is working the control unit sounds a confirmation tone and flags that the detector has passed the test.
i-on160 4. Administration 6. Press n until you see: TEST Walk Test 7. Press Y. WALK TEST Chime On WALK TEST System > The bottom line of the display shows: 8. > Press < or > to turn a chime tone on or off. When the chime tone is on, the keypads and loudspeakers will sound a chime tone for each zone that triggers while you are performing the walk test. 9. Press n.
4. Administration i-on160 Once you have selected the Walk Test option you want to use: The display shows a list of all the detectors ready for testing. The top line of the display shows you how many detectors remain to be tested. 10. Walk round and trigger each detector. The display shows an "A" at the end of the line for each detector you trigger successfully. If you have enabled the Chime then every time you trigger a detector the keypads and loudspeakers give a double tone chime.
i-on160 5. 4. Administration Press Y. The display shows: TEST Sirens & Sounders > 6. Press n until you see: TEST Outputs 7. Press Y. TEST O/P R1>03>01 O/P R1>03>01 Off The bottom line of the display shows the first in a list of the outputs installed on the system. 8. Press u or n to display the output you wish to test. a). Press >. The control unit turns on the output. Check that that it is working as expected.
4. Administration i-on160 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n until you see:. MENU Test > 5. Press Y. TEST Sirens & Sounders > The display shows: 6. Press n until you see: 7. Press Y. The display asks you to press any button on the remote you wish to test. If there are no remotes available the display briefly shows: 8.
i-on160 4. Administration For each button you press you will see a similar message, for example: b) SS:9 RM02,B3:User02 Toggle op1 SS:9 Press a button on any other remote that you wish to test. The display shows information for any remote allocated to a user of the system, for example: 9. RM01,B2:User01 Prt Set All Press Y to end the test. TEST Remotes > Panic Alarms 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag).
4. Administration i-on160 the buttons down until the transmit LED on the PA flashes). The top line of the display shows he user the PA is allocated to. The bottom line of the display shows the strength of the signal received by the system from the remote. If the signal strength is less than 2 you should contact your installer. a) Press and hold the buttons on any other PA that you wish to test. The display shows information for any PA allocated to a user of the system, for example: 9.
i-on160 4. Administration The display asks you to present the prox tag you wish to test to the keypad. No Prox Tags Learnt If there are no prox tags available the display briefly shows: 8. Hold the prox tag against the front of the keypad. TESTING PROX TAGS User: User02 The bottom line of the display shows the user that the prox tag is allocated to. a) Hold any other prox tags that you wish to test up against the keypad (one at a time).
4. Administration i-on160 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n until you see:. MENU System Config > 5. Press Y. SYSTEM CONFIG Facilities On/Off > . The bottom line of the display shows: 6. Press Y . The bottom line of the display shows the current status of the Chime facility: “On” means the loudspeakers will sound a chime tone every time a detector with the “Chime” attribute is triggered.
i-on160 4. Administration present a tag). 4. Press n until you see:. MENU System Config 5. Press Y. SYSTEM CONFIG Facilities On/Off > The bottom line of the display shows: > 6. Press n until the display shows: SYSTEM CONFIG Set Date & Time 7. Press Y. SET THE DATE 01/01/2010 The top line of the display shows “Set the date” and the bottom line shows the current date in number format (day/month/year). The day is highlighted. 8. Key in the correct date. Use the format dd/mm/yyyy.
4. Administration i-on160 “07:06”. 11. Press Y. The control unit saves you changes and the display returns to the date and time menu option. SYSTEM CONFIG Set Date & Time > Note: The internal clock adjusts itself for daylight saving in Spring and Autumn. Calendar Set Using the calendar set option you can program the control unit to set or unset the alarm system (or parts of it) at fixed times of day on a seven day cycle.
i-on160 4. Administration Hint: When you are programming calendar set options it is easier to set up your exceptions first, and then add the events. Also, make sure that you have set the system time and date accurately (see page 64). Calendar Set Options To program Calendar Sets use the System Config – Calendar Sets option within the Menu. Note that you must be an Admin or Master User to program Calendar Sets.
4. Administration i-on160 Edit Event This option allows you to edit individual parts of an event if you need to change one after setting it up. Delete Event Use this option to delete an event. Add Exception Use this option to create an Exception. During the time specified by the exception none of the events linked to the exception will take place. When you add an exception, the control unit guides you through the following steps: Name. Key in a 12 character name.
i-on160 4. Administration At the end of the calendar set warning time the control unit stops the warning tone, and sets the affected partition(s) without any further delay. Deferring a Setting Event. During the calendar set warning time a user can interrupt the setting process. To do this they must key in their access code at a keypad (or present a prox tag) and select “Defer”. Note that the user must belong to the partition that is due to be set.
4. Administration i-on160 Calendar Set Example As an example, assume that you wish to set the alarm system every evening during the days Monday to Friday, and unset the alarm system every morning on Monday to Friday (leaving the system set over the weekend). In addition, you want the system to remain set on May Bank Holiday Monday, which occurs on 2 May in 2011. First of all, you would program May 2nd as an exception: 1. Make sure the display shows the standby screen. 2. Press 3.
i-on160 4. Administration make the whole day of the bank holiday an exception, so start at one minute past midnight. 13. Press Y. The display shows: 14 Key in the start date. In this example the start date is 02/05 (2nd May), 15. Press Y. The display shows: 16. Key in the end time of the exception. EXCEPTION START DATE 01/01 EXCEPTION START DATE 02/05 EXCEPTION END TIME 00 : 00 EXCEPTION END TIME 23 : 59 In the example we want the exception to end at one minute before midnight. 17. Press Y.
4. Administration i-on160 20. Starting from where we finished adding the exception: CALENDAR SET Add Exception > 21. Press u until you see: CALENDAR SET Add Event > 22. Press Y. EVENT NAME Event 01 The display shows: 23. Key in a name to remind you of the event, for example: EVENT NAME Morning unset 24. Press Y. EVENT TIME 00 : 00 The display shows: 25. Key in the time at which the event should take place, for example: EVENT TIME 07 : 45 26. Press Y.
i-on160 31. Press n until the display shows the partition that you want to set (or unset). 4. Administration EVENT ACTIONS Partition 2 No Note: If you have a part setting system then this step will not apply. 32. Press > to show the state you want the partition to go to. EVENT ACTIONS Partition 2 Unset In the example, since we are unsetting in the morning, this will be “Unset”. 33. Press Y. The display shows the first in the list of exceptions. In our example, there is only the one exception.
4. Administration i-on160 applies on each of the five working days, Monday to Friday, and sets partition 2 to Full Set. You don’t need to apply the exception, since the system will be set from Friday evening, and will not be unset on the bank holiday Monday morning. 38. Press X to leave the menu. The display shows the time and date and the control unit stores all your changes: IMPORTANT. Do not miss this step, or the control unit will discard all your programming.
i-on160 Programming Outputs During programming the installer may allocate some outputs so that they can be reprogrammed by an Administrator. This section describes how the Administrator can use those outputs. For each output you can, if you wish, set and “on” time and an “off” time so that the output will go on and off at fixed times each day. In addition, Master, Admin and Normal users can switch the output on or off at any time. To program an output: 1. Make sure the display shows the standby screen.
4. Administration i-on160 8. Press u or n to display the output you wish to edit. EDIT O/P R1>03>03 O/P R1>03>03 > 9. Press Y. EDIT O/P R1>03>03 Name > The bottom line of the display shows the first option that you can edit for the output: “Name”. 10. Press Y. The display shows the current name of the output, and places a cursor at the beginning of the name. 11. Key in a meaningful name for the output. (Hint: see Editing Text on page 32.
i-on160 4. Administration a user turns it on, but then goes off again after a set time. You can program the time it remains on. 15. Press u or n to select the option you wish to use. EDIT O/P R1>03>03 No For example: 16. Press Y to confirm your choice. EDIT O/P R1>03>03 Latched > To Program Duration Times for non-Latched Outputs First make sure that the output you wish to use is programmed as Latched=No (see steps 1 to 16 starting on page 75). 17.
4. Administration 18. Press Y. The display shows the time when the output will turn on. i-on160 O/P R1>03>03 ON TIME 00:00 19. Key in the time when you want the output to come on. Use the 24-hour clock in the format hh/mm. If the hours or minutes are “9” or less then key in a leading zero. For example: six minutes past seven in the morning will be “07/06”. O/P R1>03>03 ON TIME 06:50 20. Press Y. EDIT O/P R1>03>03 On Time > 21. Press n until the display shows: EDIT RADIO O/P 3 Off Time > 22.
i-on160 4. Administration Note: You can switch the output on and off from the Menu by selecting Outputs On/Off (see page 90). If you want to program a telecommand to control the output, see page 79. Programming Remote Controls for Users The System Config - Remotes option allows you to re-program buttons on an i-fb01 remote control. Set/Unset To program a remote button to set or unset: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag).
4. Administration i-on160 to step 10. Note: If your system is a part setting system (there are no partitions) then you cannot reprogram the unset key on a remote control. OR (if you do not have the remote in your possession) a) Press Y. The display presents a list of the registered remote controls and their users. EDIT REMOTE RM001:User 001 b) Press u or n to show the remote control you want to edit. EDIT REMOTE RM021:User 002 c) Press Y to select it.
i-on160 4. Administration a) Press Y . In the example on the right, the button is currently programmed to unset. RM001,B2:User 001 *Unset b) Press n to change the bottom line between Set, Unset, Output or No Action: RM001,B2:User 001 Set c) Press Y . RM001,B2:User 001 *Part Set All The bottom line of the display now shows the first item in a list of setting or unsetting options that you can apply to the selected button.
4. Administration If you selected “Partitions” in step 10c) the display shows: i-on160 SET PARTITION Partition 1 No c) Press > to select between “No”, “Full” or “Part”. “No” = No effect. “Full” = Full Set “Part” = Part Set SET PARTITION Partition 1 Full d) Press Y when you have finished making the changes you want. RM01,B2:User 01 *Set 12. Press X repeatedly to leave the menu when you have finished. Operate an Output To program a remote button to operate an output: 1.
i-on160 4. Administration transmit LED flash. The display shows the identity and owner of the remote control, and the button you pressed. Go on to step 10. Note: If your system is a part setting system (there are no partitions) then you cannot reprogram the unset key on a remote control. OR (if you do not have the remote in your possession) a) Press Y. The display presents a list of the registered remote controls and their users.
4. Administration i-on160 setting system (there are no partitions) then you cannot reprogram the unset key on a remote control. 10. Press n until the display shows: RM01,B2:User 01 Output 11. Press Y . O/P W1>01>02 FOUNTAIN The display shows the first in a list of outputs that are available for allocating to a remote button. The bottom line of the display shows any name the output has been programmed with. 12. Press u or n. until the display shows the output you wish to select.
i-on160 4. Administration for example: 15. Press Y . RM001: User 01 Button 2 16. Press X repeatedly to leave the menu. Deleting Remote Controls If a user has lost a remote control you should delete it from the system to make sure that no unauthorised person can use it to gain access. Also, if you wish to reassign a device to another user, you must first delete it from the system. To delete a single remote: 1. Make sure the display shows the standby screen. 2. Press 3.
4. Administration i-on160 OR (if you do not have the remote to hand.) a) Press Y. The bottom line of the display shows the first in a list of the known devices. DELETE REMOTE RM01:User 01 b) Press n until the bottom line of the display shows the remote you wish to delete. DELETE REMOTE RM02:User 02 c) Press Y. DELETE REMOTE Delete 11. Press Y. The control unit deletes the remote from its memory. The remote can no longer be used on the system. Remote Deleted followed by: REMOTE Delete > 12.
i-on160 4. Administration 7. Press Y. REMOTE Edit > 8. Press n until the display shows: REMOTE Delete All > 9. Press Y. DEL ALL REMOTES Are you sure? The display shows: (Press X if you decide you do NOT want to delete all remotes.) 10. Press Y. All Remotes Deleted followed by SYSTEM CONFIG Remotes > 11. Press X repeatedly to leave the menu. To register remote controls with users once again enter the Menu and select Users - Edit User (see page 42).
4. Administration i-on160 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4. Press n until you see:. MENU System Config > 5. Press Y. SYSTEM CONFIG Facilities On/Off > 6. Press n until the display shows: SYSTEM CONFIG Call Downloader > 7. Press Y. CALL DOWNLOADER Tel No 1 > 8. Press n until the display shows Telephone Number 1 or 2, or IP Address 1 or 2 as instructed by your installer.
i-on160 4. Administration Redirecting Speech Messages Note: This option is available only if you have the a speech dialler module fitted inside the control unit and it has been programmed by the installer. You can use the About menu to check if you have a communication module fitted, see page 91. If you need to re-direct speech messages to new telephone numbers then: 1. Make sure the display shows the standby screen. 2. Press 3. Key in your access code (or present a tag). MENU Omit Zones > 4.
4. Administration i-on160 of the cursor. 11. Press Y to store the changes you have made. TELEPHONE NAME 2 Tel No 02 The display now shows the current name of the telephone number. 12. If necessary, key in a new name for the telephone number, for example: TELEPHONE NAME 2 Office_ (See page 32 for instructions on how to key in text.) 13. Press Y to store the changes you have made. PHONE BOOK Office 14. Press X repeatedly to leave the menu.
i-on160 6. 7. 4. Administration example “PORCH LIGHT”. Press n until the display shows the output you wish to operate: RADIO OUTPUT 2 PORCH LIGHT Off Press > to change the state of the output. RADIO OUTPUT 2 PORCH LIGHT On Note: Outputs connected to radio output modules may take several seconds to change state. 9. Press Y. The display returns to the “Outputs On/Off” menu, and the control unit operates the selected output.
4. Administration 6. Press Y . The bottom line of the display shows your control unit type and its software revision. 7. Press X repeatedly to leave the menu. i-on160 ABOUT PANEL I-ON160 V1.00 i-on160EX 02/11/2010 12:20 Seeing Which Communications Module Is Currently Installed: 1. Make sure the system is idle. 2. Enter Installer Menu. INSTALLER MENU Detectors/Devices> 3. Press u until the display shows: INSTALLER MENU About > 4. Press Y. ABOUT Panel > 5. Press n.
i-on160 List of Menu Options Item Omit Zones Users Add User Edit User (for each user:) Name Type (not U01) Partitions (not in part setting system) Code Prox Tag Remote Panic Alarm Delete User View Log Test Siren & Sounders Wired Keypad Walk test Outputs Remotes User Panic Alarms Prox Tags System Config Facilities On/Off Chime Set Date & Time Calendar Set Speech Phone Book Edit Outputs Remotes Call Downloader Outputs On/Off About Page 93 Page 33 39 47 35 36 36 37 34 41 42 44 50 51 52 52 55 56 58 59 61 62
4.
i-on160 4.
4.
i-on160 Alarm Functions At a Glance Display shows: Time and date when system off (unset). First zone to alarm after alarm Read log here. NO A 1 2 abc 3 def B 4 ghi 5 jkl 6 mno C 7 pqrs 8 tuv 9 wxyz D * 0 # Glowing = On (set) Flashing = Part Set Off = Off (unset) Key in access code here OK Hold prox tag near face of keypad. Setting and Unsetting IN ORDER TO: DO THIS: THE SYSTEM WILL: Turn the system on: EITHER: Start the exit tone. Key in ACCESS CODE and press Y OR present tag.
i-on160 After an Alarm IN ORDER TO: DO THIS: THE SYSTEM WILL: Switch off siren: EITHER: Key in ACCESS CODE OR present tag. Stop the siren. The keypad display shows the first zone to alarm. Reset the system: Press Y. Keypad display shows time and date. Read the log: Press + ACCESS CODE (or tag) + 3 + Y. Keypad display shows most recent event. Press n. Keypad display shows older events. Press u. Keypad display shows newer events. For more information see page 12 .
