Operation & Service Manual 823209 2/01 136 Reciprocating Saw 136 R V X Series: 136 Tool Type: R Speed: Reciprocating V Handle: Variable X Spade NORTH AMERICA EUROPE CooperTools P.O. Box 1410 Lexington, SC 29071 Cooper Power Tools GmbH & Co.
Safety Recommendations For your safety and the safety of others, read and understand the safety recommendations before operating this saw. is accidently engaged. Do not use tool to drain residual air from air line. A self-relieving valve is recommended for this purpose. Always wear protective equipment. Work Environment. Work areas should be kept clean and free from clutter. Visitors should be kept away from work area.
Safety Recommendations movements and postures dictated by the job design, it may be necessary for the employer to take steps to prevent further occurrences. These steps might include, but are not limited to, repositioning the workpiece or redesigning the workstation, reassigning workers to other jobs, rotating jobs, changing work pace, and/or changing the type of tool used so as to minimize stress on the operator.
READ SAFETY RECOMMENDATIONS BEFORE CONNECTING TOOL. OPERATING INSTRUCTIONS 2. Insert the blade into the blade clamp until it bottoms. When the blade is properly positioned: the hole in the blade shank will align with the hole (B) Fig. 2, in the backside of blade clamp. The Cleco reciprocating saw is designed to operate on 90 psig (6.2 bar) maximum air pressure, using a 5/16" (8mm) x 8' whip hose. If additional length is required, the next larger hose size may be connected to the 8' whip hose.
USING THE SAW STARTING WORK Consult the Blade Selector Charts for the blade best suited for the material to be cut. For greatest economy, use the shortest blade suitable for the thickness of the material to be cut. Be sure the material to be cut is rigid. Small work pieces should be securely clamped in a bench vise or to a work table. As the work progresses in scroll or curved cut-out pieces, the material may be adjusted to accommodate the movement of the saw.
ALL-PURPOSE SAW BLADES A blade for every type of sawing application; will cut smoothly and easily through wood, metal and composition material. Blades designed for use on Porter-Cable, Cleco and most competive saws. Proper Blade Selection for metal: ALWAYS select a blade where at least three teeth are engaged in the thickness of the metal.
Porter-Cable Blades 7
DISASSEMBLY REASSEMBLY HANDLE The tool is reassembled in the reverse order of disassembly. Inspect all parts for damage or wear. It is recommended that new rotor blades be installed at each repair cycle. If not replaced, the used ones must measure a minimum of 3/16" (4.7mm) at both ends. Should the throttle valve seal 847426, need replacing, unscrew the throttle valve cap 867753, for removal of the throttle valve and components.
RECIPROCATING SAW HEAD 204699 204694 204680 204681 204684 204686 204679 204693 204700 204695 204696 204692 204691 204690 204697 204701 204678 204759 204702 204688 204676 204689 204682 204698 204703 204675 204687 204676 204676 204688 204685 204704 204675 204677 204683 SAFETY INSTRUCTIONS ! WARNING Electrical and/or explosive hazard. Be certain that the object being cut does not contain electrical wires or gases. 204204 1. Use eye and hearing protection. 2.
RECIPROCATING SAW MOTOR 204712 869449 847528 812165 204312 869448 204222 ROTOR COLLAR PART NO. SIZE 864489 847525 864493 865417 .122" .124" .126" .128" RECIPROCATING SAW MOTOR PARTS LIST Part No. * ONLY ONE ROTOR COLLAR REQUIRED. 10 204222 204312 204712 812165 847525 847528 864489 864493 865417 869445 869448 869449 Name of Part Rear Bearing Plate Cylinder (incls. 812165) Rotor Cylinder Pin Rotor Collar .124" Front Rotor Bearing Rotor Collar .122" Rotor Collar .126" Rotor Collar .
RECIPROCATING SAW HANDLE AND MOTOR HOUSING SUBASSEMBLY 812977 864195 204706 204720 204709 864582 204707 612136 204727 204708 204711 204715 204715 615643 204713 204724 204714 204706 204707 204708 204709 204710 204711* 204713 204714 204715* 204720 204724* 204727 413056 612136 615643 812977 833961 847426 864195 864582 867732 867753 867756 867758 NAME OF PART Motor Housing Insert Washer Spacer Throttle Valve Motor Housing Plate Throttle Bushing Throttle Pin Muffler Handle Muffler Lock Nut Thrott
CooperTools 670 Industrial Drive Lexington, SC 29072 Phone: (803) 359-1200 Fax: (803) 359-2013 www.cooperindustries.