Energy Guide

INSTALLATION INSTRUCTIONS
WARNING:
• Turn OFF circuit breaker or remove fuse(s) and verify that power is off before wiring.
•
Never wire any electrical device with power turned on. Wiring the device with the power on may cause permanent damage to the device and void the warranty.
•
If you are unsure about any part of these instructions, or if the wiring does not match the descriptions given, you should call a qualified electrician.
CAUTION:
1
. Use only with 120V AC 60 Hz.
2. Must be installed and used in accordance with all applicable electrical codes.
3
. If a bare copper or green ground connection is not available in the wallbox, contact a licensed electrician for installation. Do not install without proper ground connections.
4
. Do not exceed maximum device ratings.
5. For use ONLY with permanently installed fixtures of these types: Incandescent/Halogen, Magnetic Low Voltage (MLV), Electronic Low Voltage (ELV), Fluorescent,
C
ompact Fluorescent, LED
6. May also be used with motors up to 1/4 HP
7. To avoid overheating and possible damage to other equipment, do not use to control receptacles.
8
. Use only #14 or #12 copper wire with these devices.
Installing 5 Button Timer
R
efer to the wiring diagram and install the timer according to these directions.
Wire the timer switch according to wiring diagram #1 using the wire nuts provided.
1. The timer black wire will connect to the hot wire (black) in the wallbox.
2
. The timer red wire will connect to the wire which goes to the light fixture.
3
. The timer green wire will connect to the ground wire in the wallbox.
4. Install the timer loosely using the mounting screws provided.
5. Apply power temporarily and verify that the timer works by pushing any of the 5 buttons to verify the load turns on. If the lights do not work then refer to troubleshooting guide.
6
. Turn power OFF and go to COMPLETING THE INSTALLATION.
COMPLETING THE INSTALLATION:
1. Secure Timer into the wall box using two mounting screws provided.
2. The circuit breaker should now be turned on.
3. Allow the timer to stabilize for 5 seconds. The timer is now ready
4. Press one of the buttons (1 through 5). The load should turn ON and the corresponding LED should turn ON. Press the button 6 and the load should turn OFF.
5. Install the decorative wallplate.
TROUBLESHOOTING:
If you have a problem with your Timer, first follow this guide. If the problem persists, call the customer service hotline at 1-866-853-4293 between 8:00 A.M. and 6:00 P.M. EST weekdays.
SYMPTOM POSSIBLE CAUSE SOLUTION
Light does not turn on. 1. Circuit breaker or fuse is turned off. 1. Turn circuit breaker on.
2. Bulb is defective. 2. Replace light bulb.
3. Poor connection. 3. Verify all wiring connections.
4. Timer may be wired incorrectly. 4. Check wiring.
Light does not automatically turn off. 1. The device is in Bypass mode. 1. Press button 6 to confirm that the timer can be turned OFF.
COOPER WIRING DEVICES LIMITED 2 YEAR WARRANTY
Cooper Wiring Devices (CWD) warrants this device to be free of defects in materials and workmanship in normal use and service for a period of two years from date of original
purchase. THIS 2 YEAR LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS, OR LIABILITIES, EXPRESSED OR IMPLIED (INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS IN DURATION IN EXCESS OF 2 YEARS FROM THE DATE OF ORIGINAL CONSUMER
PURCHASE). NO AGENT, REPRESENTATIVE, OR EMPLOYEE OF CWD HAS AUTHORITY TO INCREASE OR ALTER THE OBLIGATIONS OF CWD UNDER THIS WARRANTY.
To obtain warranty service for any properly installed CWD device that proves defective in normal use send the defective device prepaid and insured to Quality Control Dept.,
Cooper Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269; in Canada: Cooper Wiring Devices, 5925 McLaughlin Road, Mississauga, Ontario L5R 1B8.
CWD will repair or replace the defective unit, at its option. CWD will not be responsible under this warranty if examination shows that the defective condition of the unit was
caused by misuse, abuse, improper installation, alteration, improper maintenance or repair of damage in shipment to CWD.
CWD SHALL HAVE NO RESPONSIBILITY FOR INSTALLATION OF THE DEVICE, OR FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR ANY SPECIAL, INCIDENTAL,
CONTINGENT, OR CONSEQUENTIAL DAMAGES OF ANY KIND, RESULTING FROM DEFECTS IN THE DEVICE OR FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT.
RED
OUTPUT
(BARE)
GREEN
(WHITE/NEUTRAL)
GROUND
HOT
(BLACK)
BLACK
(BLACK)
Light
Fixture
HOT