Quick Start Guide

www.eaton.com
www.eaton.com/wiringdevices
EIS-0239-E (REV.B)
www.eaton.com
www.eaton.com/wiringdevices
EIS-0239-E (REV.B)
WARNINGS AND CAUTIONS:
Turn circuit breaker to OFF position or remove fuse(s) and test that power is OFF before installation process.
• Never wire any electrical device with power turned ON. Wiring dimmer HOT may cause permanent damage to dimmer and void
warranty.
• If you are not sure about any part of these instructions, please contact a licensed electrician.
IMPORT
ANT: Z-Wave Universal dimmer will not work or will become damaged if wired incorrectly and warranty will be voided. Refer to wiring
instructions provided.
• Use only with 120V/AC 60 Hz.
• Do not exceed maximum rating of dimmer as indicated on the device.
• Must be installed and used in accordance with all national and local electrical codes.
• If a bare copper or green ground connection is not available in the wallbox, contact a licensed electrician for installation.
• Use only #14 or #12 copper wire rated for at least 75º C with these devices. DO NOT USE WITH ALUMINUM WIRE.
NOTES:
• The Z-Wave Universal Dimmer is wired directly to the light fixture.
The Z-Wave Universal Dimmer is not compatible with standard 3-way switches.
• For Multi-location applications (3-Way or 4-Way) the Z-Wave Accessory Dimmer (RF9642-Z) is used along with one Z-Wave Universal
Dimmer.
• The Z-Wave Accessory Dimmer communicates via RF signals to control the light from more than one location.
• For multi-location control use Z-Wave Universal Dimmer Master direct wired to the light along with Z-Wave Accessory (RF9642-Z).
The Z-Wave Accessory dimmer does not require direct connection to the light (use Z-Wave Association function).
Z-WA
VE DEVICE NETWORK INSTRUCTIONS:
• This product may be added to a new or existing Z-Wave network. An Eaton Wiring Devices Z-Wave device has a blue LED,
which will blink when the device is not included in a Z-Wave network. The LED stops blinking when the device is in a network.
• This product works with other Z-Wave products from different vendors and product categories as part of the same network.
• This product is a listening node and it will act as a repeater in the Z-Wave network. It will perform the repeater function with
Z-Wave products from Eaton and from other Z-Wave vendors.
• This secure Z-Wave Plus device will only associate with other secure devices based on the Z-Wave controller it’s being used with.
Please refer to instructions provided with the controller for more details.
Adding Z-Wave Smart Universal Dimmer to a Z-Wave Network:
1. To include this device in a Z-Wave network, select the command on your Z Wave controller for inclusion (Install, Add Device,
Add Node, Include Device, etc.). Then press the device ON/OFF switch one time to include it in the network.
2.
Based on the controller, the controller may ask you to scan the QR code (Figure 1) or manually enter 5 digit code under the QR code
to install the device as a secured device. You may find this QR code on the device or included in device packaging.
3.
After the Device is added to the network, the LED will stop blinking. This indicates the device is installed in the Z-Wave network.
Removing Z-W
ave Smart Universal Dimmer from a Z-Wave Network:
1.
To exclude this device from a Z-W
ave network, select the setting on your Z-Wave controller for exclusion
(Uninstall, Remove Device, Remove Node, Exclude Device, etc.).
2.
Once your controller is in exclusion mode, press the device ON/OFF switch one time to exclude it from the network. The LED will start
blinking.
For a Quick start Guide on how to install this device with Eaton’
s home automation hub & other compatible Z-Wave Certified Controllers,
please scan the QR code (Figure 2)
Operating Instructions:
• Press ON/OFF button once to turn lights ON at previously selected level.
• Press ON/OFF button again to turn lights OFF.
• When lights are OFF, press and hold ON/OFF button for 2 seconds for full brightness of overhead light.
• Delayed OFF: When overhead lights are ON, press and hold ON/OFF button for 2 seconds until the blue LED blinks. After the preset delay,
the lights will begin fading to OFF (Default present delay is 10 seconds; you can configure this through a compatible Z-Wave controller for
up to 2 minutes). Please refer to configuration parameters table.
• Amber ON/OFF LED indicates that dimmer is turned ON (Default).
Dimming Level Adjustment (RF9640-N only)
For maximum compatibility with different load types, RF9640-N allows the user to set the minimum dim level or low end trim.
Also to save on power consumption RF9640-N allows the user to set the maximum dim level or high end trim.
• After adding the dimmer to a network, press ON/OFF button to turn ON the overhead light.
• Press and hold ON/OFF button for five seconds until the blue indicator LEDs begin to cycle rapidly (Notice
- After two seconds blue
indicator LEDs will start to flash indicating activation of the ‘delayed OFF’ feature. Continue to hold the ON/OFF button for three additional
seconds until the blue indicator LEDs begin to cycle rapidly.)
• Once the indicator LEDs start cycling, release the ON/OFF button. Dimmer will set the light to the previously saved minimum l
evel. During
initial setup, the light will set to the factory minimum default.
• Press either the dim UP or DOWN buttons to change the minimum level until the light output is acceptable.
• Once light output is acceptable, press ON/OFF button once. Blue indicator LEDs will start to cycle rapidly again and the dimmer light will
go to previously saved maximum level.
• Press either the dim UP or DOWN buttons to change the maximum level until the light output is acceptable.
• Press ON/OFF button once, LED will flash indicating completion of programming.
Note - User could ignore setting max or min while programming by pressing ON/OFF button without changing the light level.
Rapid start feature (RF9640-N only):
This feature ensures that LED/CFL lights turn on when the dimmer preset level is low
. With this setting enabled, the lights may momentarily
come ON brighter than the preset level (less than one second) and then dim down to the preset level. Depending on the type of light used,
this feature may not be needed. To enable/disable the feature, turn lights ON. Press and hold the ON/OFF button for 10 seconds until the blue
indicator LEDs flash for the third time, then release the button. This feature is disabled by default.
Changing LED Indicator brightness: (RF9640-N & RF9642-Z):
This feature allows the change of the brightness of the blue LED indicators on the device.
There are 5 levels (including fully OFF and full brightness) to change the LED indicator brightness level either while the device is ON or
OFF state.
Changing the LED indicator brightness when the device is an ON state:
• Turn the overhead light ON.
• Press and hold the ON/OFF button for 15 seconds till the LED indicator flashes for the fourth time. (second time for RF9642-Z
)
• Release the ON/OFF button.
• Use the dim UP or DOWN button to change the LED indicator level (it will cycle between the five levels).
• Once the brightness level is selected, double tap on the ON/OFF button and this value will be saved
.
Changing the LED indicator brightness when the device is an OFF state:
• Turn the overhead light OFF.
• Press and hold the ON/OFF button for 15 seconds till the LED indicator flashes for the second time.
• Release the ON/OFF button.
• Use the dim UP or DOWN button to change the LED indicator level (it will cycle between the five levels).
• Once the brightness level is selected, double tap on the ON/OFF button and this value will be saved
.
Local Reset (RF9640-N & RF9642-Z) (Please use this procedure only when the network primary controller is missing or otherwise inoperable)
The device could be reset locally. This will cause the device to be excluded from its network and restore to factory default.
Before leaving the network the dimmer will send a notification to the controller indicating its departure from the Z-Wave network.
• Turn the device ON.
• Press and hold ON/OFF button for 20 second till the LED flashes for the fifth time. (third time for RF9642-Z)
• Release the ON/OFF button.
• LED will start flashing rapidly
. Once the LED starts blinking slowly, that indicates the device is not part of the network.
ACCESSORY
ACCESSORY
ACCESSORY
White
White
Master Control Accessory
Disconnect Switch
Red
Black
Black
Green
Green
Switch Identification
Disconnect Switch
Pull out to change bulbs
(Master Dimmer only)
Press to DIM
Light level may be
adjusted with lights
ON or OFF
Press to BRIGHTEN
ON/OFF Button
Light level
indicators
(blue)
LED ON/OFF
indicator (amber)
RF9640-N - Z-Wave Plus Universal Smart Dimmer - For dimmable LED/CFL/ INC/ MLV/ ELV/HAL/FLR
RF9642-Z - Z-Wave Plus Smart Accessory Dimmer - For multi-locations
Load Type Single Gang 2-Gang 3-Gang
RF9640-N
INC/ELV/FLR/HAL/MLV 600W 550W 500W
CFL/LED 300W 300W 300W
Single Location Control Installation (requires one Master Dimmer) Two Location Control Installation (requires one Master and one Accessory)
Black
Red
Neutral
120V
Light Fixture
Green
Ground
White
White
MASTER
DIMMER
Neutral
Hot
Neutral
120V
Green
Ground
White White
White
Black
ACCESSORY
DIMMER
Hot
Light Fixture
Black
Red
Neutral
120V
Green
Ground
White
White
MASTER
DIMMER
Neutral
Hot
Wattage Ratings
RF9640-N
Parameter Description Value
1 Delayed OFF Time 0 to 127 secs
2 Panic ON Time 0 to 127 secs
3 Panic OFF Time 0 to 127 secs
4 Not Used N/A
5 Power Up State 1=OFF 2= ON
3 = Last State
6 Panic Mode Enable 0=OFF
1=ON
7 Dimmer Ramp Time 0 to 127 secs
8 Kickstart Enable/Disable 0 Disables
1 Enables
9 Reset Max/Min Levels to factory default 0
10 Not Used N/A
11 Set Minimum Dimming Level 1 to 99
12 Set Maximum Dimming Level 1 to 99
13 BLUE LED Brightness Level while the dimmer is ON 0-4
14 BLUE LED Brightness Level while the dimmer is OFF 0-4
15 Amber LED Brightness Level while the dimmer is ON 0-4
16 Amber LED Brightness Level while the dimmer is OFF 0-4
RF9642-Z
Parameter Description Value
1 Delayed OFF Time 0 to 127 secs
2 Panic ON Time 0 to 127 secs
3 Panic OFF Time 0 to 127 secs
4 N/A N/A
5 Power Up State 1=OFF 2= ON
3 = Last State
6 Panic Mode Enable 0=OFF
1=ON
7 Dimmer Ramp Time 0 to 127 secs
8-12 Not Used N/A
13 BLUE LED Brightness Level while the dimmer is ON 0-4
14 BLUE LED Brightness Level while the dimmer is OFF 0-4
15 Amber LED Brightness Level while the dimmer is ON 0-4
16 Amber LED Brightness Level while the dimmer is OFF 0-4
Configuration parameters:
RF9640-N RF9640-NRF9642-Z LOCATION A
ENGLISH
Association groups supported:
Group 1 (lifeline) 5 node maximum
Group 2 (ON/OFF) 5 node maximum
Group 3 (DIM Up/ DIM Down) 5 node maximum
Figure 1
(For Reference Only)
Figure 2
Quick Start
Guide

Summary of content (2 pages)