Instruction Sheet

2
NOTE:Coverplatemountstorecessedmounted
standardjunctionboxes(Fig.2).Junctionboxmustbe
atleast1-1/2in.indepthforproperinstallationfor
recessedmountapplication.
1. Installprotectivereectors(I)ontolampholders
byliningupthenipplesonthecovers,overthe
lampholderslots.Lockintoplacebytwisting
coverscounterclockwise(Fig.3).
2. Lineuptheholesonthemountingbracket(H)with
theholesonyourjunctionbox.Usingeither(2)#6
screwsor(2)#8screws(D)(dependingonthe
sizeoftheholesinyourjunctionbox),attachthe
mountingbracket(H)toyourjunctionbox(Fig.4).
3. Threadxturewiresthroughcoverplategasket(B).
4. Connectcoppercoloredgroundwire(comingfrom
thexturecoverplate)tothehousegroundwire
usingwirenut(E)provided.Connectxtureblack
wiretohouseblackwire,xturewhitewiretohouse
whitewireusingwirenuts(E)provided(Fig.5).
5. Attachxture(A)tothemountingbracket(H)using
thecenterbolt(G)provided.Besurenoloosewires
remainstickingoutfromunderneaththecoverplate.
Insertplasticcolor-matchedplug(F)incenterbolt
holefornishedappearance(Fig.6).
6. Applysiliconecaulkingaroundedgesofcoverplate
 andinanyopenholestoprovideawatertightseal
 fromrainandmoisture.
7. Insertlampholdergaskets(C)intolampholder
assembly,tightlyagainstlampholder,andscrew
bulbsintoeachlampholder(Fig.7).(Donot
overtightenbulbs.)
8. Turnonpoweratmainfuse/breakerbox.
OPERATING YOUR FIXTURE
1. Moveslideswitchonbottomofthesensorto
“TEST”.Setsensitivityslideswitchtomedium
or“M”(Fig.8).
2. Turnonthepowertoxture.Allowxturetowarm
upapproximately90secondsbeforetesting.(Lights
mayormaynotcomeonduringwarm-upperiod;
thisisnormal.)
3. Aimsensorheadindesiredposition.
NOTE:Maintainairspacingbetweenlampsandsensor
head,atleast1in.Makesuresensorheadispositioned
withcontrolswitchesfacingtowardstheground.
4. Walkacrossthedetectionzoneatthefarthest
distanceyouwishyourdetectortodetectmotion.
5. Adjustsensitivityuntilyougetdesiredresults.
Formorerange,aimsensorheadslightlyupwards.
Forlessrange,aimsensorheadslightlydownward.
6. Moveslideswitchto4minor12min(AUTOmode),
ortooneofthethree“NightTimeOn”settings.At
dusk,lightswilloperateinthe“AUTO”or“Night
TimeOn”settings.
Mode of MODE Knob How to Set
Operation Adjustment Power Switch
Test Setting
LightsshouldturnONwith
motionbothdayandnight.
LightsshouldturnOFF
after4seconds.
Keepthepower
tothextureON.
TEST
Motion Activated
(“Auto” Setting)
LightsshouldturnONwith
motiononlyatnightandshould
turnoffafter4or12min.
ofnomotion.
AUTO4MIN
or
AUTO12MIN
Keepthepower
tothextureON.
Dusk-to-Dawn Setting
Override Mode
(activated only at night)
LightsshouldstayON100%
brightnessfromdusktodawnand
thenresettothe“AUTO”or“Night
TimeOn”settingatnextdawn.
AUTO4MIN
or
AUTO12MIN
or
ALL“NIGHTTIMEON”MODES
Turnthepower
OFF-ON-OFF-ON
within3seconds.
Fig.2
OctagonalRound
1-1/2in.
ENERGY STAR
®
TomeetENERGYSTAR
®
requirements,thephotosensorcontrolknobmustbeinthe
“Auto”modetopreventoperationduringfulldaylight.Maximumlampwattagecannot
exceed250watts.
SELECTING YOUR DESIRED FEATURE
Return to “Auto”
or “Night Time On” Settings
(motion activated)
from any of the above settings.
AUTO4MIN
or
AUTO12MIN
or
ALL“NIGHTTIMEON”MODES
TurnthepowerOFF
foratleast90seconds
andthenbackON.
Continuous Override Mode
(Standard Floodlight Setting)
LightsshouldstayON
continuouslybothdayandnight
(mustberesetmanually).
TEST Turnthepower
OFF-ON-OFF-ON
within3seconds.
ENERGYSTAR
®
issponsoredbytheU.S.
EnvironmentalProtectionAgency&U.S.
DepartmentofEnergy.
Visitwww.energystar.govtolearnmore.
D
H
D
Fig.4
2 Hour
NIGHT TIME ON
then Motion Activated
LightsshouldturnON
automaticallyatnight100%
brightnesfor2hours,thenreset
toregularautomotionsettingsfor
theremainderoftheevening.
NIGHTTIMEON
2HR
(2Hours)
Note:Oncethelighthascome
ONintheselected“NightTime
On”mode,youcannotchange
themodesettinguntilthenext
dawn.Thelightwilloperatein
therst“NightTimeOn”mode
selected(2hour,4hour,6hour)
evenifchanged.
Keepthepower
tothextureON.
4 Hour
NIGHT TIME ON
then Motion Activated
LightsshouldturnON
automaticallyatnight100%
brightnesfor4hours,thenreset
toregularautomotionsettingsfor
theremainderoftheevening.
NIGHTTIMEON
4HR
(4Hours)
Note:Oncethelighthascome
ONintheselected“NightTime
On”mode,youcannotchange
themodesettinguntilthenext
dawn.Thelightwilloperatein
therst“NightTimeOn”mode
selected(2hour,4hour,6hour)
evenifchanged.
Keepthepower
tothextureON.
6 Hour
NIGHT TIME ON
then Motion Activated
LightsshouldturnON
automaticallyatnight100%
brightnesfor6hours,thenreset
toregularautomotionsettingsfor
theremainderoftheevening.
NIGHTTIMEON
6HR
(6Hours)
Note:Oncethelighthascome
ONintheselected“NightTime
On”mode,youcannotchange
themodesettinguntilthenext
dawn.Thelightwilloperatein
therst“NightTimeOn”mode
selected(2hour,4hour,6hour)
evenifchanged.
Keepthepower
tothextureON.
Fig.6
F
G
A
Fig.5
Wallmount
Eavemount
B
A
A
E
E
E
Fig.3
I
A
Fig.7
C
C
Fig.8
MODE
TEST
4 MIN
12 MIN
2 HR
4 HR
6 HR
SENSITIVITY
H
M
L
AUTONIGHT TIME ON
1-1/2in.