Instruction Manual

Indoor / Outdoor Pan/Tilt System

I．Features:

z Compact and attractive appearance, Indoor / Outdoor design；

z Motor running stably；

z Flame-retarded ABS material；

z Adjustable horizontal limit switcher, the unit capable of operation with load to 6Kg；

z RS485 data communication；

z With internal decoder, Multi-protocol, baud rate for selectable；

z Pan speed: 5°/sec； Tilt speed: 5°/sec；

z With line scanning function；

II．Description of the Dip-switcher setting:

１．Dip-switcher

ON DIP

1 2 3 4 5 6

ON DIP

1 2 3 4 5 6 7 8 9 10

SW2SW1

6-Dip switcher: 1 – 4 for Protocol, 5 – 6 for Baud rate；

10-Dip switcher(frontal 9-DIP) is for the address setup:1～511, count it as the binary system.

2 ．The setting of the protocol and the default baud rate:

Protocols

Selection of Protocols Normal Baud Rate

DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6

SAMSUNG ON OFF OFF OFF OFF ON

B01 ON OFF OFF OFF OFF ON

PELCO-D ON ON OFF OFF OFF OFF

PELCO-P/4800

OFF OFF ON OFF

ON OFF

PELCO-P/9600 OFF ON

Longcomity OFF ON ON OFF OFF ON

HUNDA600 ON ON ON OFF OFF ON

LILIN OFF OFF OFF ON OFF ON

PAGE 1
Indoor / Outdoor Pan/Tilt System I．Features: z Compact and attractive appearance, Indoor / Outdoor design； z Motor running stably； z Flame-retarded ABS material； z Adjustable horizontal limit switcher, the unit capable of operation with load to 6Kg； z RS485 data communication； z With internal decoder, Multi-protocol, baud rate for selectable； z Pan speed: 5°/sec； Tilt speed: 5°/sec； z With line scanning function； II．Description of the Dip-switcher setting: １．Dip-switcher SW2 SW1 ON DI P
PAGE 2
ALEC OFF ON ON 1 2 ON OFF ON 3 ．The setting of the baud rate: Dip-switcher Baud Rate 3 4 5 6 2400bps OFF OFF 4800bps ON OFF 9600bps OFF ON 19200bps ON ON B01/ 9600Bps ON ON 1 AELC/ 9600Bps 2 3 4 5 SAMSUNG/ 9600Bps 6 ON 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 ON 1 2 3 4 5 PELCO- D/ 2400Bps 6 ON PELCO- P/ 4800Bps 1 ON 1 2 3 4 5 PELCO- P/ 9600Bps 6 4 ．Address setting： Dip-switcher Dome Address DIP-1 DIP-2 DIP-3 DIP-4 DIP-5 DIP-6 DIP-7
PAGE 3
… 511 ON ON ON ON ON ON ON ON ON Before the application of the Dome pan/tilt, the address codes should be set first by DIP1 to DIP9 of SW1 on PCB in binary 8421 coding system, in which DIP1 means lower bit and the maximum address is 511. State ON of the DIP-SWITCH means “1” while OFF means “0”. Some address codes of the DIP-SWITCH are set as above. 5. Selection of 120Ω Terminal Resistor The DIP-10 of SW1 is used to select 120Ωterminal resistor.
PAGE 4
180. 8 84. 4 1/ 4’ × 20 .
PAGE 5