Wireless/Wired Network IP Camera (For PC View) Night Vision & Remote Operation User Manual 0
Thank you for buying our IP camera IPCAM AJ Series IP Camera products are designed and equipped for local and remote network video surveillance system, including wired IP bullet camera, wireless IP bullet camera, IP IR dome camera, IP IR waterproof camera, IP Pan/Tilt/Zoom Camera etc. We adopt high performance chip to ensure high quality media processor which processes audio and video collection, compression and transmission. Standard M-JPEG compression format ensures clear and streaming video performance.
Table of CONTENTS 1. Product Introduction ...........................................................................................3 1.1. Safety Introduction .........................................................................................3 1.2. Product Specifications................................................................................. ....3 1.3. System Requirements........................................................................................3 1.4. Product Views…………….........
1. Product Introduction 1.1 Safety Instructions (1). Use the proper power source. Do not use this product with a power source that supplies more than the specified Voltage (100-240V AC). (2). Never insert anything metallic into the camera. Inserting metal object into the camera can be a source of dangerous electric shock. (3). Do not operate in wet or dusty environment. Avoid places like a damp basement or dusty hallway. (4). Do not attempt to disassemble the camera.
*-Maximum support 15 users viewing at the same time, no limit for users if using forwarder Server function; *- Built in Web Server, convenient for users to use standard browse to realize the real time monitoring and setting administration; /n wireless networking; *-Support WIFI WIFI::802 802..
Figure 1.1 2 Figure 1. 1.2 1: Audio Out , 2: Audio In 3: Ethernet interface: RJ-45 interface. Power Supply Light: constant on after power up Network light: constant sparkle after power up data transmission. 4: Antenna: 5: Power input interface: connect direct current 5V Power 1.5 Hardware Installation Follow the steps below to set up your camera hardware. Make sure to follow each step carefully to ensure that the camera operates properly 1. Install the Wi-Fi antenna (For wireless model) . 2.
3 Figure 1. 1.3 1.6 Software Installation 4 Figure 1. 1.4 Open the CD Install the follow software: ”—“ Next ”—“ Install ”—“ Finish ”. 1. ActiveX: Click “OCX setup setup”—“ ”—“Next Next”—“ ”—“Install Install”—“ ”—“Finish Finish” 2. Search Tool: Open the CD, click ,The Search Tool will run automatically.( No need to install. You can copy this software to your desktop.) 5 Figure 1. 1.
2. Software operation 2.1 Search Tool Software 2.1.1 Search the IP address of the camera camera. When the device has been mounted properly, you can double click the Icon “ ” run this IP address search tool. Figure 2.1 Note: The software searches IP Servers automatically over LAN. There are 2 cases: 1. No IP Cameras found within LAN. After about 1 minute search, the Equipments List Field not show the IP address address.. 2. IP Cameras have been installed within LAN.
4. If you don don’’t know how to configure your camera camera’’s IP address. You can click “ Update Update”” button. The Search Tool software can help you configure a usable IP camera automatically. 2.1.2 Configuration of the Network Once your camera camera’’s IP address address’’ Subnet Mask, Gateway, DNS Server is the same as your PC or router, you need configure the camera camera’’s Network parameter manually.
Figure 3.1 Default username: admin Password: no password. Input the correct user name and password, the Sign In interface will pop-up. There are three models to login (figure 3.2).. Figure 3.2 (1) ActiveX Mode (For IE Browser): available in IE6.0 or above explorer (2) “RTSP Stream Mode”: available in Firefox, Safari, and Google browser. (3) “No Plug-In Mode”: available in smart phone browser. (4) SD card video playback online 3.2. View via IE Browser.
Choose Active Mode (For IE Browser) Browser),, and sign in. The first time login the camera, maybe get ActiveX prompt as the picture below below,, please download the Ocx(or run in CD) and install first then choose Run Add-on Add-on,, refresh and login the camera again, then will see live video, details as below: Figure 3.3 After Download Ocx-Setup (oPlayer Software), Click and install it, untill finished. Figure 3.
Figure 3.3 Windows XP system Figure 3.4 Win7 System Note: If there is still no live video after run ActiveX, please try to enable the ActiveX options of IE security settings, please do the follow steps: 1. Close the firewall of your computer. ” browser > “Tool ” > “Internet Options ” > “Security ”> 2.
Figure 3.5 Figure 3.6 ” menu-> “Internet Explorer ”, choose “Internet In Addition Addition:: you can also click “start start” menu->“ Explorer” ” -> “Internet Explorer ”, enter to Security setting. attributes “ to enter, or via “Control Panel Panel” ->“ Explorer” 3. If there is still no image, please close your anti-virus software, and then try step 1 & 2 again. 4.
Figure 3.7 NOTE NOTE: Make sure that the firewall or anti-virus software doesn doesn’’t block the software or ActiveX. If you couldn couldn’’t see live video, please close your firewall or anti-virus software, and try again. 3.3. View via Safari, Firefox, Google Browser Choose Server Push Mode (For Safari, Firefox, Google Browser) Browser),, and sign in Server Push Mode doesn doesn’’t support ActiveX, so some functions are not available, such The speed control bar, Zoom etc.
3.4.
Figure 3.8 The Pan/Tilt Feature only work when the cameras have this Pan/Tilt function. This option enables log detection. After the online user clicks this button, a log is entered into the camera camera’’s Log Data documenting the IP address of users who have accessed the IP camera. This Option enables alarm detections too. This button make the camera Vertical cruise (for the Pan/Tilt Cams). This button make the camera Level cruise (for the Pan/Tilt Cams). This button flips the image vertically.
This setting changes the image frequency. This setting changes the image brightness. This setting changes the image contrast. This option resets all main menu options to factory default. This option opens the camera camera’’s recording functionality menu. This option takes a snapshot of the current screen and saves the snapshot to the PC PC’’s Hard Drive. This option enables User-to Camera audio. If the online user This option enables Camera-to-User audio.
equipment. Embedded applications, up to 4 devices at the same time-line. Click the ” in the “second road equipment equipment”” and double-click “Current list of devices in the LAN LAN” device entry name, host address, Http port will automatically be filled, require the user to ” Repeat this process you can fill in the correct account name and password, click “Add. Add.” ” button. continue to add devices. Finally do not forget to click on the “Settings Settings” Figure 3.9 Figure 3.10 3.5.
Figure 3.11 This sector is for DHCP and IP configuration configuration,, port forwarding is needed, If you choose to set IP address address,,please fill in the relative IP address address,, subnet mask, gateway, DNS server, Http port; 3.5.3 Wireless Settings 1. Make sure the router is a wireless router. 2. Make sure the Wi-Fi antenna installed. 3. Make sure whether there is encryption of the WLAN of the router, if there is encryption, keep the key. ”>”Scan ”, please scan 2times, 4.
Figure 3.12 3.5.4 Dynamic DNS Setting (DDNS) 3.5.4.1 DDNS Setting: (1): Click > “DDNS Service Settings Settings””. Figure 3.13 (2): Choose the DDNS DDNS,, there are 4 kinds of options: (1): Manufacturer Manufacturer’’ DDNS DDNS:: We provide a free DDNS: vipcam.org vipcam.org.. This domain is provided by manufacturer. Note: 88safe.com is old DDNS provided by manufacturer also. If you want use the manufacturer’s free DDNS, Please Choose to use vipcam.org.
Figure 3.14 (2): The Third Party DDNS DDNS:: This domain is provided by the 3 rd party, such as Dyndns, Oray, 3322 ” If you use the third party DDNS, please choose the server you need need,, such as “3322.org 3322.org” “dyndns.org or or“ dyndns.org”” as below: Figure 3.
Figure 3.16 You have to register an account firstly, keep the user, password, host, then fill in it. Note: Only one DDNS can be chosen, for example, if you use manufacturer manufacturer’’s DDNS, the 3rd party one won won’’t work, if use the 3rd party DDNS, the manufacturer manufacturer’’s one won won’’t work. 3.5.4.2 Port forwarding settings settings:: 1: Setting the IP address of the camera The default IP address of the camera is : Http://192.168.1.
(1) Login the router. ” (2) Choose “Forwarding Forwarding””, select “Virtual Servers Servers” (3) Click the Add New button, pop-up below: ), IP address of the camera, then click Save Fill the service port (except 80 80), The port and IP address should be the same as Camera. BELKIN: (1) Login the router. ” (2) Choose “Firewall Firewall””, select “Virtual Servers Servers” (3) Input the port (except 80 80)) and IP address, then click save. Note: The port and IP address should be the same as Camera.
Figure 3.18 DLINK: (1) Login the router. ” (2) Choose “Advanced Advanced””, select “Virtual Servers Servers” (3) Input the port, IP address, Protocol, then click save. ” should be the same as camera Note: The “public port port”” & “private port port” camera’’s port, choose the protocol to be “both both””.
Figure 3.29 After all these 4 steps done, then you can use the DDNS freely, check the DDNS status from the camera as below, and get the link of DDNS for internet view. Step: “Login Login””>” ”: ”>”Device Info Info” Figure 3.20 3.5.5.3 DDNS Register For example, you can go to Dyndns website to register a free account. http://www.dyndns.org / http://www.dyndns.com http://www.dyndns.com..
Step1: enter http://www.dyndns.com/ and Create Account Figure 3.21 Step2: Set the username and password as below: Figure 3.22 Step3: After a minute, you will receive a E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://www.dyndns.com/confirm/create/ONMzltcCBk6mcHJI5MhVD0g https://www.dyndns.
Figure 3.23 Figure 3.24 Step4: When the Account Confirmed, login and start using your account. Choose Add 25 26 )page. Host Services(Figure 3. 3.25 25)) and enter Add New Hostname (Figure 3. 3.26 26)page. Figure 3.
26 Figure 3. 3.26 Step5: On the Add New Hostname page. 1) input your Hostname. 2) choose Host with IP address 3) click Use auto detected IP address xxx.xx.xx.xxx xxx.xx.xx.xxx.. Then click Create Host. ” 4) after you have added a New Hostname , you need “Proceed to checkout checkout” Figure 3.
Figure 3.28 Figure 3.29 30 ),and can use it in the DDNS Step6: Now you obtained a Dynamic Domain Name(Figure3. Name(Figure3.30 30),and 5.5 Service Settings(details: 3. 3.5.5 5.5)) Notice: If you have a dynamic IP address, Make sure you have download the DynDNS DynDNS’’s “Update ”. And installed it succeed in your computer. Client Client” Figure 3.
3.5.6 E-mail and FTP service Settings Figure 3.31 The above setting is a preparation for the alarm function, the sender should be recipient 1、2 2、3 3、4 4 is filled with recipient E-mail entered the sender sender’’s email address address，recipient SMTP server should be filled with the sender email SMTP server e.g. the address address；SMTP server，e.g. and enter mail.163.com. Generally SMTP port sender email address is abc@163.com abc@163.
password, FTP upload directory directory,,FTP mode mode,,FTP mode has two options: PORT and second POSV. If needs a quick upload image, then select it, edit upload image interval interval（second second） 3.5.7.
3.5.8 Record&Capture Path This sector is for Record&Capture Path in your computer.It include: Record&Capture Path, Record file length(MB) length(MB),, Record time length(Minute) length(Minute),, Reserved disk space(MB) space(MB),, Record cover cover.. Figure 3.34 3.5.9 Reset/Firm Ware Upgrade This sector is for camera firmware upgrade, it includes device system firmware and device application firmware Be cautious to apply for it! Figure 3.35 31 .
.1 Restore Factory Settings 3.5.9 3.5.9.1 When users forget password, we can restore ex-factory settings, when click, a picture will pop up, Click ok, and wait for 1 minute and you can use it normally. User setting feature restores Figure 3.35 9.2 Reboot Equipment 3.5. 3.5.9.2 Click restart, it appears the above picture, click ok, wait for 1 minute and you can use it normally Figure 3.
range of warranty. You could ask repair depend on the card. We only charge for changed components, the maintenance charge is free. c) When the products need maintenance, hand up the card with products to the manufacture or local distributor. d) Take apart item crust, tear up the sealing label privately, this is out of warranty range. e) We do not accept the damaged item due to modification or add other functions.
