Installation and Operation Manual for Six inches Middle-Speed Dome P/T V1.
Operation Manual for Intelligent Speed Dome Camera I. Points for Attention 1. Please read the operation manual carefully before installing and operating the product. 2. The product takes power supply of AC24V. The rated input voltage of the camera is marked on the base or other corresponding place. 3. During the course of transportation, storage and installation, the product should be avoided from incorrect operations such as heavy pressing, strong vibration etc.
Operation Manual for Intelligent Speed Dome Camera II. Description of Functions The intelligent dome camera is a hi-tech CCTV product which incorporates high-clarity color camera, panoramic speed-variable PAN/TILT, multifunctional decoder, CPU processor, memory chip into a whole. It can largely reduce connection and installation processes of components in the system, rise up reliability of the system and facilitate installation and maintenance.
Operation Manual for Intelligent Speed Dome Camera 27x f =3.6 to 98 mm (F1.5 to F3.8) 1 Lux (Common / 0.01 Lux（B & W） Ⅲ . Setup of the Dome Camera 1.
Operation Manual for Intelligent Speed Dome Camera 8 9 10 11 12 13 14 15 16 17 18 OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF OFF ON ON OFF OFF ON ON OFF OFF ON OFF OFF OFF OFF ON ON ON ON OFF OFF OFF ON ON ON ON ON ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF … 10
Operation Manual for Intelligent Speed Dome Camera Some protocols and the states of the coding switches of normal baud rate of these protocols are shown as follows: ON B01/ 9600Bps ON 1 2 3 4 5 PELCO- P/ 4800Bps 6 ON PELCO- D/ 2400Bps 1 2 3 4 5 6 1 2 3 4 5 6 ON 1 2 3 4 5 PELCO- P/ 9600Bps 6 4. Setup of the Baud Rate of Communication. As shown in Figure 2, SW2 is used to set the protocol of communication and the baud rate used by the dome camera.
Operation Manual for Intelligent Speed Dome Camera Ⅳ. The Installation of the System 1. The style of the Installation 262 1) Dimension of the Product Φ 152 Φ 219 Figure 3 2) The Style of Installation a) Wall Installation Figure 4 262 300 b) In-Ceiling Installation Φ7 Figure 5 2. Steps of Installation (taking wall-mounting as example) 1. Unpacking the carton and carefully take out the dome camera and its attachments.
Operation Manual for Intelligent Speed Dome Camera 2. Rotate the vitreous cover counterclockwise and take out it. (see Figure 6) Note: It can be ignored the steps 2,3,4,5 while the protocol and address are matching with the controller. 3. Take out the black liner. (Figure 7) 4. Based on the ID-CODE shown as Figure 2, set up the protocol used by the camera and the baud rate as per the state according to Table 1. Check the address of the camera to see if it is matched with that you need.
Operation Manual for Intelligent Speed Dome Camera 9. Install the aluminum alloy ball on the bracket (Figure 12). 10. Rotate the vitreous cover clockwise and mount it（Figure 13）. Cl ose Figure 12 Figure 13 11. Connect the control wires of the system as per Figure 14. RED CONNECTOR ( POWER I N) RED LI NE( AC24V I N) BLACK LI NE( AC24V I N) ORANGE LI NE( RS485+) YELLOW LI NE( RS485- ) BLACK CONNECTOR ( RS485 CONTROL I N) VI DEO OUT Figure 14 3.
Operation Manual for Intelligent Speed Dome Camera Power supply Power consumption Sync system Preset Patrol Auto pan scan AC24V 50/60Hz Indoor dome：12W Internal 64 presets 6 Outdoor dome：35W 360°Programmable Pan Manual Control Speed 0—30°/s Pan Preset Speed 80°/s max Pan rotation range 360°continues Title range Tilt 90° Tilt speed 12°/s max(manual & preset speed) RS485 2400/4800/9600/19200 bps Fan & heater auto-start (only outdoor dome) Control mode Baud Rate Fan & heater Environment temp Ind
Operation Manual for Intelligent Speed Dome Camera On power cannot self-check have image but have motor noise Self-check ok, but have no image Self-check ok but cannot control Vague image On power cannot control Bad connection of the power Transformer damaged Mechanical failure Camera incline Power supply not enough Video signal fault Bad connection of the video Camera damaged RS485 Bus bad connection Dome id setting is wrong Protocol setting is wrong Bad connection of the video Power supply not enough Se
