HD‐SDI SPEED DOME CAMERA USER’S MANUAL V3.
Table of Contents Precautions………………………………………….…………………………………....2 Features………………………………………………………….………….…..………….3 Technical Data…………………………………………………………………..…..…..9 Installation Guide………………………………………………….……………………10 Dome Settings…………………………………………………………..…………...…17 Operation Instructions………………………………………………..……….
2
1 Precaution 1. Please read this manual carefully before the installations and operations. 2. Transportation Security No heavy stress, violent vibration or water splash are allowed during transportation, storage. The unit should be transported in separated packing. In shipments of distributor and delivery of maintenance, any damages caused by integral packing are not covered by warranty. 3. Installation Avoid heavy stress and violent vibration during installation.
static object for long time, as it will cause Irreparable damage to the camera’s CCD. 7. Cleaning Method Please don’t use abrasive and violent detergent to clean the dome. Please choose dry fabric and neutral detergent. And please use lens paper to clean the lens. 8. Internal removing, assembly, repair and operations should be only performed by qualified service personnel. 9.
• HD‐SDI transfer mode,no IP transmission process of compressed packet and image distortion,with higher data security • Support PELCO‐P PELCO‐D protocol • Multiple compatible camera brands including Sony,HITACHI, LG, CNB,etc.
2.4 All‐weather Outdoor Design • 6 Inch High die‐cast alloy aluminum construction • High Precision Mould with high heat conductivity • Fully enclosed isolation design for heat sink • Nanometer Dustproof, waterproof and fog‐proof lens • IP66 Waterproof • 3000V lightning and surge current protection 2.5 Function Instructions • Focus / PTZ Speed Auto Match The pan/tilt rotation speed could be automatically adjusted according to the focus in/out, which makes it much more practical for manual target tracking.
and dwell time of each preset can be set. It supports up to 8 cruising tracks, each cruising track with 32 presets. • Pattern Tour Dome can memorize 600s running path or 500 programmable instructions. When start pattern tour, speed dome will move automatically according recorded action path. It supports 4 groups of pattern tours. • Guard Location The dome will automatically return to preset position if there is no operation in a period of vacant time.
up the exact moving directions on screen. And zone title is supported to display when the dome moves to the specified zone. • Auto Tracking The dome will automatically fix and track the moving object according to the user’s setup via OSD. • Motion Detection The dome will detect the changes in the defined video zone and trigger alarm. It supports to 8 video Locations, each with 4 detection zones. • PTZ and Lens Control 1) Zoom Control Users can control zoom by keyboard to get near or far images.
illumination changes. 7) OSD Setup (Only for camera with menu) Call upon preset No.95 to enter into OSD menu setup interface. Press “Focus” to choose menu items and press “Iris” to set menu contents.
3 Technical Specifications Power Supply DC12V+10% 50W Night IR Distance 120/150/180meters Manual Speed Pan 0.01o~180o, Tilt 0.01o~100o (high speed) / Pan:0.5o~35o/S, Tilt:0.5o~35o/S (Vair‐speed) Preset Speed 360 o/S (high speed) / 35o/S (Vari‐speed) Pan Angle 360o continuous pan rotation Tilt Angle 90o(Auto Flip) Presets Positions 256 Preset Accuracy +/‐0.
4 Installation Guide 4.1 Preparations 1) Basic Requirements All the electric work must be finished under the latest electric & fire prevention law and rules (and any related law and rules). Please check according to the packing list if every accessory is included. And also make sure the installation is operated as required. Please contact us for any help during the installation. 2) Installation Space and Density Checkup Please make sure the space is big enough to install our dome.
4.2 Installation Method The IR speed dome could be installed in wall‐mount and pedant‐mount 4.
Pendant Mount 4.4 Installation Procedures *Notice: The wall and ceiling must be thick enough to install the expansion bolts and can bear 4 times the weight of the dome camera itself. Wall‐mount Installation Procedures: 1) Take out the bracket from the package (as shown), mark the installation hole positions on the wall referencing to the bottom of bracket.
2) Drill the hole and install 4 pieces of M8 expansion bolt into the hole. 3) Take out the IR speed dome and put the cables through the bracket. Use M5 screws to fix the bracket and dome body.
4) Use 4 pieces of M8 screw nuts with washer to fix the bracket on the wall. Pendant‐mount Installation Procedures: 1) Take out the bracket from the package (as shown), mark the installation hole positions on the ceiling referencing to the bottom of bracket.
2) Drill the hole and install 4 pieces of M8 expansion bolt into the hole. 3) Take out the IR speed dome and put the cables through the sockets on the bottom of the pendant bracket. Use M5 screws to fix the bracket and dome body.
4) Use screw nuts with washer to fix the bracket on the wall. Notice: Pendant‐bracket is not designed for outdoor installation. If specially required, please do make sure the waterproof installation of the dome.
Dome Setting Before the dome is installed, please finish the setup of the communication protocol, baud rate and dome address. Set the DIP switch inside the dome body. The relative DIP switch site and connecting wires are diagramed below for reference.
1) Protocol Setup Our IR speed dome supports three protocols including Pelco P, Pelco D and HS. All of them supports baud rate of 9600bps、4800bps、2400bps. Set the No.1~4 dip switch for the protocol configuration. Protocol HS PELCO P PELCO D Reserved SW2‐1 OFF ON OFF … SW2‐2 OFF OFF ON … SW2‐3 OFF OFF OFF … SW2‐4 OFF OFF OFF … 2) Baud Rate Setup Set the No.5~6 dip switch for the baud rate configuration.
3) Dome Address Setup PELCO‐P & PELCO‐D Protocol Add 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 … 253 254 SW‐1 SW1‐2 SW1‐3 SW1‐4 SW1‐5 SW1‐6 SW1‐7 SW1‐8 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 1 0 0 0 0 0 0 1 1 0 0 0 0 1 0 1 1 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 0 1 0 0 1 0 0 0 1 1 0 0 1 0 0 0 0 0 1 0 1
4) Cable Definition BNC Connector: Video Coaxial Cable Power Connector: DC12V Red: RS485A Yellow: RS485B Operation Instructions 1) Main Functions Fast Call Up Our IR Speed dome supports 220 preset positions. You can activate some special functions by calling upon code number 65‐99. Serial No. Command Fast Call Up 1 Start Auto Scan Call 99 2 Start Auto Cruise Call 98 3 Start Pattern Tour Call 97 4 5 Start Auto Scan of Group No. Start Auto Cruise of Group No.
6 7 8 9 10 Start Pattern Tour of Group No. Stop Auto Mode/End up Setting Open OSD Menu Remote Reset Recover Factory Default Call 80+ Call pp+ Call 97 pp means：Group No.1‐4 Call 96 Set 95（or Call 95） Call 94 Call 82 2) System Self‐Testing The dome will do self‐testing after power up, and system status will show “Normal” if system Is running normally. If error happens, testing result will be shown in “○” or “X”. “○” means normal and “X” means error.
4) OSD Menu Functions 23
LANGUAGE The language for the on‐screen menus is Selectable. To change the display language: Press Iris Open to enter selection. All on‐screen menus are changed to the selected language. SYSTEM INFORMATION The user can check the dome system information as required. The system information includes: Dome ID, dome address, baud rate, protocol, temperature, voltage, alarm info, dome title, version, date, time, and temperature scale.
DISPLAY SETUP Display setup allows the user to define the way to display the dome titles on the monitor.
IR LED The user can open and close the IR LED manually and set up the IR LED work mode under this OSD mean. (Under normal operation mode, the user can press IRIS OPEN and IRIS CLOSE to adjust the IR LED power): 1) CONTROL MODE: AUTO: IR LED will be opened or closed automatically according to the light conditions. TIMING: LED will be adjusted according to Open and Close Time.
WIPER MAIN MENU LANGUAGE:ENGLISH RESTART FACTORY DEFAULTS HELP The user can make adjustment for the wiper under this menu (suitable for wiper‐equipped dome) 1. Numbers : Move the cursor to “NUMBER” and press IRIS OPEN to enter the setup of Wiper Number. Move the joystick up and down to select number (1‐10),then press IRIS OPEN to confirm. 2.Speed: Move the cursor to “SPEED” and IRIS OPEN to enter the setup of Wiper speed.
IDLE IDLE setting means if there is no command for the dome for a period of time, the dome will run the actions as defined. 1) TIME: Move the cursor to “TIME” and press IRIS OPEN to enter, and move the joystick up and dome to select among 30 sec, 1 min, 5 min, 10 min and 30 min. And press IRIS OPEN to confirm. 2) ACTION: Move the cursor to “ACTION” and press IRIS OPEN to enter. Move the joystick to select the actions including” NONE, PRESET, SCAN, SEQUENCE, PATTERN. Press IRIS OPEN to confirm.
ALARM The dome system has 2alarm inputs and 1 alarm output. (optional function). When an alarm is received, an input signal to the dome triggers the user defined action (such as presets, patterns, etc.), and at meantime the alarm output signals is activated. ALARM NO.: Move the cursor to the ALARM NO. Press IRIS OPEN to enter and move the joystick up and down to select the alarm input no. (Channel 1 and Channel 2) INPUT STATE：Set the alarm contact status. There are two input states, OPEN and CLOSE.
PRIVACY MASK Privacy mask allows the user to mask the privacy areas with black frame. The user can set up 8 privacy masks at most. MASK NO.: Move the cursor here and press IRIS OPEN to enter the setup of Mask Number of the privacy zone, ENABLE: To enable or disable this privacy mask function. SET: Move the cursor here and press IRIS OPEN to enter the mode of setting the privacy mask. Move the joystick (Left/Right/Up/Down) on the screen to set up the privacy zone and press IRIS OPEN to confirm.
CLOCK The dome can display the data and time. And the user could enter this CLOCK menu to set up the DATE and TIME. DATE: Move the cursor here and press IRIS OPEN to enter. Move the joystick left and right to choose the date position and move it up and dome to adjust the figures. Press IRIS OPEN to confirm. TIME: Move the cursor here and press IRIS OPEN to enter. Move the joystick left and right to choose the time position and move it up and dome to adjust the figures. Press IRIS OPEN to confirm.
PASSWORD The dome features password protection function to prevent unanthorized changes to the dome settings. If the PASSWORD function is enabled, the operator can not access any dome setting without entering a valid password. EDIT PASSWORD: Move the cursor here and press IRIS OPEN to enter. Please under the old password before set up the new password. The initial password is “111111” ENABLE: Move the cursor here and press IRIS OPEN to enter. Move the joystick to select between “ON” and “OFF” .
DOME TITLE The user can set up the dome title to define each camera. Dome title support up to 12 characters. Move the cursor according the left steps and select INPUT. Press IRIS OPEN to enter. 1) Move the joystick left and right to position “←”, and press IRIS OPEN to delete the character at“←”. Press IRIS CLOSE to exit the edit mode. 3) Move the cursor to “” and press IRIS OPEN to enter.
AUX MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT The user can set up the auxiliary output to trigger other devices from an alarm or a controller. Move the cursor to AUX and press IRIS OPEN to enter to select “ON” or “OFF” to enable or disable this function.
MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT DOME SETTINGS BACK EXIT SOFT LIMIT The user can set up the soft limit to define the left and right boundaries for the pan movement SOFT LIMIT:Move the cursor here and press IRIS OPEN to enter.Now the joystick to select “ON” or“OFF”to ennable or disable this function.
MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT DOME SPEED To make a selection of the dome speed,the user can enter this menu to set up. Move the cursor to BACK/EXIT and press IRIS OPEN to run the command of BACK or EXIT.
POWER ON ACTION The user can define the dome action when power on, Move the cursor to POWER ON ACTION and press IRIS OPEN to enter the mode of setup. NONE PRESET SCAN SEQ PATTERN 2 (default) No action. Dome goes to preset.
MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT DOME SETTINGS BACK EXIT CAMERA The dome can automatically recognize the main camera modules in the market.For the cameras it can not recognize,the user can set up here. CAMERA:Move the cursor here and press IRIS OPEN to enter the setup mode.Move the joystick up and down to select the camera types.
COMMUNICATION TEST MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT The dome can do self diagnosis for the communications between keyboard and speed dome. The test needs to match with our software VK200. If the self testing is successfully finished via the software, the system will show up the testing results as left diagram.
TILT ANGLE MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT The user can set up the tilt angle under the menu of TILT ANGLE Move the cursor to”TILT ANGLE”and press IRIS OPEN to the setup of tilt angle .Move the joystick up and down to select the angle and press the IRIS OPEN to confirm.
OTHERS MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT DOME SETTINGS BACK EXIT The user can set up TEMP MODE, INTERNAL FAN, PRESET FREEZE, STOP TIME. MENU OFF TIME and NORTH ZERO here under the menu of “OTHERS” TEMP MODE: To set up the control mode of dome fans and heaters. It includes three modes of AUTO, FAN HIGH SPEED and FAN LOW SPEED.
CAMERA MAIN MENU LANGUAGE:ENGLIS RESTART FACTORY DEFAULTS HEIP EXIT CAMERA SETTING FOCUS MODE:AUTO DIGITAL ZOOM:OFF BACKLIGHT:OFF PICTURE FLIP:OFF ZOOM SPEED:NORMAL DAY NIGHT:AUTO BACK EXIT The user can make adjustment for the cameras under this menu. FOCUS MODE: AUTO FOCUS allows the camera lens to remain in focus during zooming in, zooming out and pan/tilt movement. Move the cursor here and press IRIS OPEN to enter.
CAMERA ADVANCED The use can set up more detailed parameters of camera here under the menu of CAMERA ADVANCED. WB: To set up the white balance of the camera. Options include AUTO, MANUAL. INDOOR and OUTDOOR. The use can select different mode according the different locations. RED GAIN: Only can be adjusted whet WB set as manual. BLUE GAIN: Only can be adjusted whet WB set as manual. BIRGHT: To set up the brightness of the image. Move the cursor here and press IRIS OPEN to enter.
PRESET The dome supports 256 presets. Please check the following steps to set up a preset. 1) PRESET NO.: Move the cursor here and press IRIS OPEN to enter the setup of Preset Number. Move the joystick to select a preset number (1‐64 and 100‐255) and press IRIS OPEN to confirm. 2) TITLE: Move the cursor here and press IRIS OPEN to enter the setup of Preset Title. Check the detailed above in DOME TITLE settings. 3) : Move the cursor here and press IRIS OPEN to enter.
AUTO SCAN The dome supports 8 groups of auto scan. Please check the following steps to set up a scan. 1) SCAN NO.: Move the cursor here and press IRIS OPEN to enter the setup of SCAN Number. Move the joystick to select a preset number (1‐8) and press IRIS OPEN to confirm. 2) TITLE: Move the cursor here and press IRIS OPEN to enter the setup of SCAN Title. Check the detailed above in DOME TITLE settings. 3) : Move the cursor here and press IRIS OPEN to enter.
AUTO CRUISE (SEQUENCE) The dome supports 8 groups of auto cruise and each cruise supports 32 presets. . Please check the following steps to set up cruise. 1) SEQ NO.: Move the cursor here and press IRIS OPEN to enter the setup of Sequence Number. Move the joystick to select a preset number (1‐8) and press IRIS OPEN to confirm. 2) TITLE: Move the cursor here and press IRIS OPEN to enter the setup of Sequence Title. Check the detailed above in DOME TITLE Settings.
PATTERN TOUR The dome supports 4 pattern tours and each pattern cover at most 10 Minutes of 500 commands. Please check the following steps to set up a pattern. 1) PATTERN NO.: Move the cursor here and press IRIS OPEN to enter the setup of Pattern Number. Move the joystick to select a pattern number (14) and press IRIS OPEN to confirm. 2) TITLE: Move the cursor here and press IRIS OPEN to enter the setup of Pattern Title. Check the detailed above in DOME TITLE settings.
ZONES The use can set up zone title when the camera moves to a defined location, which will make it much easier for the user to identify the location. The dome supports 8 zone titles. Please check the following steps to set up a zone 1) ZONE NO.: Move the cursor here and press IRIS OPEN to enter the setup of Zone Number. Move the joystick to select a zone number (1‐8) and press IRIS OPEN to confirm. 2) TITLE: Move the cursor here and press IRIS OPEN to enter the setup of Zone Title.
TIMING ACTION TIMING ACTION allows the user to set up the actions of the dome in 7 days (each day with 8 timing segments). When fishing the setup, the dome will do the actions according to the setup motion during the defined time segment. NO.: Here shows the day within a week. Move the cursor here and press IRIS OPEN to enter. Move joystick up or down to select the Serial No. (1‐8) for the timing action. Press IRIS OPEN to confirm.
MOTION DETECT The user can set up 8 motion detection scenes (each scene with 4 detecting areas) under this menu. The alarm output will be triggered when moving objects enter these detecting areas SCENE NO.: Move the cursor here and press IRIS OPEN to enter the setup of Scene Number. Move the joystick to select a preset number (1‐8) and press IRIS OPEN to confirm. : Move the cursor here and press IRIS OPEN to enter. Move the dome to a user‐defined detecting scene. Press IRIS OPEN to confirm.
AUTO TRACKING Under the auto tracking mode, the dome will auto track the moving objects entering the scene. When the object is moving out of the scene, the dome will return to a preset position as defined after the defined time. SENSITIVITY: The user can set up the auto tracking sensitivity under this menu. When set as LOW, the dome will do auto tracking when obvious object entering the screen. When set as HIGH, the dome will do auto tracking when small object moving into the screen.
TRACKING SCENE SET TRACKING SCENE SET: Here the user can set up the scene that the dome will get back to when finishing the action of auto tracking. Move the cursor here and press IRIS OPEN to enter. Move the dome to the wanted scene and press IRIS OPEN to confirm. DELETE: Move the cursor here and press IRIS OPEN to delete the return scene. RETURN DELAY: To set up the time that dome will waiting to return to this scene. RESTART The dome allows the user to reset its settings remotely under this menu.
FACTORY DEFAULTS FACTORY DEFAULTS will allow the user to recover all the setting to factory default setting. Move the cursor here and press IRIS OPEN to enter.
