NVMS-1000 User Manual Version 2.1.
Contents 1 2 3 4 5 6 7 Software Introduction ........................................................................................................................................ 1 1.1 Summary ................................................................................................................................................ 1 1.2 Operation Environment ......................................................................................................................... 1 1.
7.7 Synchronized Playback ........................................................................................................................ 36 Alarm Management ......................................................................................................................................... 37 8.1 Sensor Alarm ....................................................................................................................................... 37 8.2 Motion Detection Alarm .....................
1 NVMS-1000 User Manual 1 Software Introduction In this chapter, you will read a detailed introduction of the operation environment, install & uninstall of this software. 1.1 Summary Network Video Monitoring System (hereinafter referred to as ―NVMS-1000‖) is a monitoring client which is specially designed for network video surveillance. After the network video monitoring system is well built, the super administrator can control the video input signal devices, such as cameras, domes, etc.
2 NVMS-1000 User Manual 1.3 Install and Uninstall 1.3.1 Install the Software Double click ―Setup.exe‖ to enter the Installation Wizard Click【Next】to install. Select ―I accept the terms of license agreement‖ and click 【Next】to continue. Click 【Browse】 button to change the directory to save the program files. Click【Next】to continue.
3 NVMS-1000 User Manual Check ―Vcredist_x86‖ and click【Next】to install this plug-in. Click【Next】; check ―I have read and accept the license terms‖ and click【Install】to start installation of Vcredist_x86; then click【Finish】to complete installation. Please refer to the below three pictures. Note: If the above plug-in has been installed, please click 【Repair】 and click【Next】to repair software. Click【Finish】 button to finish repairing.
4 NVMS-1000 User Manual Click【Next】to continue. At last, check ―Create desktop shortcuts‖, and then click【Finish】button to complete installation. 1.3.2 Uninstall the Software Click ―Start‖ at the bottom of the desktop to find the shortcut of NVMS-1000 ; then click ―Uninstall‖ to pop up a dialog window; click 【 Yes 】 to uninstall the software. At last, click【Finish】button to finish uninstall .
5 NVMS-1000 User Manual 2 Login Software 2.1 Login First time to login: ① For the first time to run the NVMS-1000, you need to register a super administrator. You shall self-define the username and password. ② To avoid forgetting the password, you can set some questions to help you find the password quickly. ③ After you input your user name, password and set the questions and answers, click【Register】to enter into the software. Input the username and password created by you.
6 NVMS-1000 User Manual 2.2 Control Panel Instruction The control panel of NVMS-1000 is shown below There are five areas in the main interface of this software. The descriptions of each area are as follows: Area Description Area Description 1 Function Area 2 Tab Bar—to display the operated functions 3 Menu Bar 4 Alarm Information List. 5 Status information list Description of Menu Bar Menu Description Start Export the control panel, live preview, playback tab and lock or exit the client.
7 NVMS-1000 User Manual Playback: To remotely play the local record. E-map: To manage and display maps, hot zones and hotspots. To operate E-maps – zoom in/out e-maps, view hot zones and hotspots, display alarm information on the map. Device Management: To create, modify or delete areas, devices and cameras. Group and Scheme Settings: To create, modify or delete camera groups and schemes. User Account and Permission: To add, modify, delete user and user permission.
8 NVMS-1000 User Manual 3 Device Management In the control panel, click icon to enter the device management interface. 3.1 Add Device Click button to enter the interface. ① Select device type and input device name; ② Input IP address or domain, port of the device, then input its user name and password. ③ Create an area. If you haven’t created area, you can click ―Create a New Area‖ to create. ④ Check ―Upload bandwidth more than 2M‖ according to the actual network situation.
9 NVMS-1000 User Manual want IP camera to connect ECMS-1000‖ and input ENVMS-1000 Address, ECMS-1000 Port and Device ID (Here ECMS-1000 refers to NVMS-1000). Input the Device ID according to the device ID of DVR or IP camera device. Add Online Devices Click button to automatically search online devices in the local network. Click a device to display its basic information. Double click it to add it. If the device is added, this device will be hidden in the search device interface. 3.
10 NVMS-1000 User Manual Change Deviec Port Number Click “Change the Port Number of Device” to change the port of selected device. Change Device User Name Click “Change Device User Name” to change the device account name. Change Device Password Click “Change Device Password” to change device password. Change Connection Bandwidth Check “Upload bandwidth more than 2M” according to the actual situation. Note: Checking or not checking it will affect the stream choice of live preview.
11 NVMS-1000 User Manual View Device Log Click “View Device Log” to enter the interface. Choose the type of system logs; enter start time and enter time to search the log information of the device. View Disk Information Click “View Disk Information” to check the detail information of disk from the list. Change Network Configuration Click “Change Network Configuration” to enter the interface. You can change HTTP port, Server port; network address, etc.
12 NVMS-1000 User Manual Device Alarm Output Configuration Click “Alarm Output Configuration” to enter the interface. Select an alarm output and holding time; then edit a name for it. You can enable buzzer alarm and set a time for it. Abnormal Alarm Configuration Click “Abnormal Alarm Configuration” in to enter the interface. Choose the alarm type according to your need. Enable ―Buzzer Alarm‖ and select alarm out.
13 NVMS-1000 User Manual DDNS Configuration Click ―DDNS Configuration‖ to enter. You can configure the basic parameters of DDNS. 3.3 Area and Camera Management In the control panel, click ―Change Camera Settings‖ under Device to enter the interface. You can modify or delete the area and manage the cameras. Select a camera you want to setup as shown on the below figure. The camera without some functions will not display ―Image Video Parameters‖ as shown in the following picture.
14 NVMS-1000 User Manual 3.3.1 Click Area Management button to create area. Select an area and click its name. button to change Select an area and click it. button to delete Select an area and click a window. to pop up ① Check the camera on the left column and click button to add the camera to the area. ② Check the camera on the right column and click button to remove the camera from the area. Select a camera and click button to modify the area of this camera.
15 NVMS-1000 User Manual 3.3.2 Camera Management The real-time image will be displayed after selecting a camera. You can setup the parameters of this camera. Image Settings Image settings include image video parameter, image quality and image display. Click “Image video parameters” to enter the interface . ① Adjust the brightness, contrast, saturation and chroma of the image. ② Clicking 【Restore Default】 button will restore the above parameters to factory default settings.
16 NVMS-1000 User Manual Under the record of system You can set schedule and record stream. How to set schedule? The picture of setting schedule record of device: The picture of setting schedule record of system: Click 【Set Schedule】 button to pop up the follow figure. Check ―7x24‖ or ―Custom Schedule‖ to set schedule. Click icon and move the cursor to select the time. Click icon to delete the selected time.
17 NVMS-1000 User Manual Motion Detection Alarm Settings Click “Area and Sensitivity” under Motion Detection Alarm Setting to enter the interface. ① Drag slide bar to set the sensitivity value. The higher the value is, the more sensitive it is. ② Click ―Erase‖/ ―Add‖, then hold press ―Ctrl‖ and left click mouse to delete /add the area you want. ③ Click 【All】/【Reverse】/【Clear All】 button to select area or clear all the area quickly.
18 NVMS-1000 User Manual Video Loss Alarm Settings Click “Video Loss” to enter the interface. The steps of configuring video loss are same with the device settings, please refer to the video loss chapter of device user manual. Video Loss of System Click “Video Loss of System” to enter the right window. You can set the video loss of system. PTZ Settings Click “PTZ Protocol Configuration” under PTZ Settings to enter the interface. You can enable or disable PTZ.
19 NVMS-1000 User Manual The definitions of the buttons are below: Buttons Description means the dome rotate up; dome rotate up right; rotate left down; rotate left; means the dome rotate up left; means the means the dome rotate down. means the dome means the dome rotate right down; means the dome means the dome rotate right; means the dome stop rotating Drag the slider bar to adjust rotation speed of the dome Focus button. Click obtain short focus button to obtain long focus. Click Iris button.
20 NVMS-1000 User Manual 4 Group and Scheme Setting In the interface of control panel, click “Group and Scheme Setting” to enter the interface. Please refer to the below picture: 4.1 Create, Change or Delete the Camera Group In the above interface, click button to create a group. Select a group in the group list, click to delete it. button Select a group and click button to enter the interface as shown on the right. You can change the group name and dwell time interval in this interface. 4.
21 NVMS-1000 User Manual to add the selected cameras to the group on the right. ③ Check cameras on the right, then click button to remove them from the group. 4.3 Create, Change or Delete Group Dwell Scheme Scheme is used for dwelling group by group. Therefore, at least one group should be created. Click “Change or Delete the Group Dwell Scheme” on the left side of the menu to enter the interface as below. 4.3.1 Create Scheme Click button to create a scheme.
22 NVMS-1000 User Manual Select a scheme and click button. Then click “Add or Remove Group of the Scheme” to enter the interface. Check group on the left and click button to add the selected group to the scheme on the right. Check group under scheme on the right and click button to remove the group.
23 NVMS-1000 User Manual 5 Live Preview In the interface of control panel, click “Live Preview” to enter the interface: Buttons description of live preview: Toolbar on the display window: Icon Description Icon Description Close image Snap Start/stop manual record PTZ control. Clicking the icon will display the control panel of PTZ.
24 NVMS-1000 User Manual Right button functions: Menu Description Menu Description Snap Snap picture Open Manual Recording Start manual record Start talk Start or stop talk Camera Configuration Enter the interface of the area and Camera configuration Stream Choose stream to view. PTZ Control To display the control panel of PTZ Enable Audio Enable or close audio Close Preview Close single channel preview Full Screen To display in full screen 5.1 Preview 5.1.
25 NVMS-1000 User Manual 5.2 Dwell Preview After setting up group or scheme (Please refer to chapter 4 for creating group), enter to the live preview interface and click button to display the group list or scheme list. The below sections will introduce how to realize group dwell and scheme dwell. 5.2.1 Group Dwell Preview Start Group Dwell In the interface of live preview, click shortcut on the left side to display the groups , drag a group under scheme to any window( icon stands for group).
26 NVMS-1000 User Manual Single Channel in Full Screen Double click the selected window to view in full screen. Double click again to recover the window. Stream of Live Preview Right click on the display window to choose recording stream as shown on the right. The above stream is main stream (eg: D1 25fps) and the below is sub stream(eg: CIF 6fps). Modify Device Stream: Click button on the display window to enter the Area and Camera Management interface.
27 NVMS-1000 User Manual 5.4.3 Record and Snap Path In the control panel , click “Basic” to enter the interface. Click “Partition and Path” to select a folder to save the record files. Click “Set the Default Path of Snap” under Partition and Path to set up the path to save the snap files. 5.5 Multi-screen to Preview In the interface of live preview, click button to plus a tab of live preview.
28 NVMS-1000 User Manual for enabling new talk with another device which is launching talk. 5.6.2 Broadcast ① Click “System” on the menu bar of software at the upper right ; choose “Broadcast” to enter the interface. ② Click button to pop up a window; then check the devices you want to broadcast, click 【OK】button to save the setting. ③ Click broadcast. button to stop 5.7 PTZ Control 5.7.
29 NVMS-1000 User Manual 6 Record Management NVMS-1000 supports manual record, schedule record, motion detection record and sensor alarm record. This chapter will introduce the above four record types respectively. 6.1 Manual Record Select a channel and click Then click button or right click to choose ―Open Manual Recording‖ to start recording. button or right click to choose ―Close the Manual Recording‖ to stop recording.
30 NVMS-1000 User Manual 6.3 Motion Detection Record In the control panel, click “Area & Camera Settings” under Device to enter the interface. Select a camera and click ‖Set Motion Alarm ” under Motion Detection Alarm Settings as shown on the right figure. Enable Alarm of device and set the relevant trigger. Click ‖System Trigger ” under Motion Detection Alarm Settings as shown on the right figure. Click button to select channel.
31 NVMS-1000 User Manual 6.4 Sensor Alarm Record In the control panel, click “Change Camera Settings” under Device to enter the interface. Select a sensor and click as shown on the right. button Click button to choose associated record cameras. When the sensor alarm is triggered, the selected cameras will be recorded automatically. 6.5 Set Record Partition In the control panel, click “Set Record Partition” under Playback as below. You can choose a partition for storing record.
32 NVMS-1000 User Manual 7 Playback Management In the interface of control panel, click “Playback” record files. to enter the interface. You can play back the local stored Area Descriptions: Area Description Area Description 1 Playback Area 2 Toolbar 3 Record time Area 4 Resources Area 5 Time search or type search Area Buttons Description of Area 2 Icon Description Screen mode.
33 NVMS-1000 User Manual then click this button to play frame by frame. Backup the start time Backup the end time Download Event list.
34 NVMS-1000 User Manual 7.1.2 Click Playback by Searching Event button to display the event list. Double click an event to play this event record. Note: and buttons on the timeline are used to expand and narrow down the time bar, so you can choose a more accurate playback time. What’s more, you may also change playback speed by dragging bar. 7.2 Snap When Playback Click button on the playing window to capture pictures. A message prompt will pop up after snapping. 7.3 Clip and Backup Record 7.3.
35 NVMS-1000 User Manual Select record channel, start time and end time, checkmark event type and then click【Record Search】button to search record information. After the information is searched, a backup information window will pop up by clicking【Download】button. Click【Browse】button to choose save path. Then click【OK】button to download record. 7.5 Download Record by Event Search Click button to display event information list. Choose a event and right click to download this event. 7.
36 NVMS-1000 User Manual 7.7 Synchronized Playback In control panel interface, click ―Synchronized playback of device‖ to enter synchronized playback interface. You can play 25 channels synchronously. Click the highlighted time block to select the time for playing, Thus, all channels will play from this time. Synchronized playback support device playback which gets rid of the limitation of the quantity of channels for playback.
37 NVMS-1000 User Manual 8 Alarm Management 8.1 Sensor Alarm In the control panel, click “Alarm Management” to enter the interface. Add or Remove Sensor of the Area In the interface of Alarm Management, choose an area, click interface. button to enter the ① Check the sensor under the area on the right and click button to move out the sensor . ② Check the sensor on the left and click to add sensor.
38 NVMS-1000 User Manual Alarm Link Setup In the interface of Alarm Management, choose a sensor and click button to enter the interface. If checking “Trigger Alarm Playback”, there will be a sound like ―beep‖ when sensor alarm is triggered. Add Associated Preview Camera Click to pop up a window; check cameras and click【OK】 button to save the setting. When sensor alarm is triggered, the alarm preview and e-map preview will pop up automatically. Select the added camera, click remove the camera.
39 NVMS-1000 User Manual Click ―Set the Motion Alarm‖ to enter the interface as right. Click “System Trigger” to enter the interface as shown on the right. Please refer to section 3.3.2 for details. 8.3 Video Loss Alarm In the control panel, click “Area & Camera Management” under Device. Click “Video Loss” to enter the interface. The steps of configuring video loss are same with the device settings, please refer to the video loss chapter of device user manual.
40 NVMS-1000 User Manual 8.4 Alarm Preview The interface of alarm preview will automatically pop up if the relevant alarm page and alarm preview have been already configured. 8.4.1 Alarm Preview Configuration Motion Detection Alarm: In the control panel, click “Change Camera Settings” under Device to enter the interface.
41 NVMS-1000 User Manual Click button on the upper right corner of the sub interface; then select “Tab View” to embed the sub interface in the main interface.
42 NVMS-1000 User Manual 9 E-Map In the control panel, click ― E-Map‖ to enter the interface as below: 9.1 Create map In the E-map interface, click 【Shortcuts】 button on the left side to appear the shortcut menu, then click “Create Map File” to enter the interface. Import a map and edit a name for it. 9.2 Modify or Delete Map, Hotspot and Hotzone In the E-map interface, click “Edit E-map” on the left side to enter the interface.
43 NVMS-1000 User Manual 9.2.1 Change or Delete Map In the above interface, click “Map File” to appear the map files on the left side. Choose a map and click to change a new name for it. 9.2.2 Add, Change and Delete Hotzone Add Hotzone Click “Map File” and choose a map and then click icon to pop up a dialog widow. ① Check a map related the hotzone ② Click to choose text color displaying under the hotzone icon. ③ Click to choose icons for the hotzones.
44 NVMS-1000 User Manual 9.2.3 Add, Change and Delete Hotspot In the E-map interface, choose a map, click to enter the interface. ① Check associated cameras and sensors ② Click hotspot. ③ Click to choose text color displaying under to choose an icon for the hotspot ④ Edit a name for the hotspot. There is another way to add hotspot. Select a map and double click the camera, or drag the camera to the map for adding hotspot.
45 NVMS-1000 User Manual Area Description: Area Description 1 Menu bar 2 Zoom in/out the map 3 Alarm preview 4 Overall display of map(suppressible) 5 Alarm message prompts Right Click on the Alarm Preview Window: Item Description Item Description Snap Picture capture Open Manual Recording Start manual record Start Talk Start talk PTZ control Click to display PTZ control panel Zoom in Zoom in the image Size of window Recover the image size Stream Choose stream to view Enable au
46 NVMS-1000 User Manual click button to tile the alarm preview windows on the right side. Right click on the map to pop up a menu bar. Choose ―Full Screen‖ to view the image in full screen. Right click on the map to choose ―Exit Full Screen‖ to exit.
47 NVMS-1000 User Manual 10 Local Log In the interface of control panel, click “Local Log” to enter the interface. 10.1 Search log Choose main type, sub type , set the start time and end time, click【Inquire】button to search the relevant log information. click【First page】 【Previous】 【Next】 【Last page】to view the information on different pages. 10.2 Log Maintenance In the log interface, click button to pop up a dialog window.
48 NVMS-1000 User Manual 11 User Management In the interface of control panel, click “User Management” to enter the interface. There is only one super user registered by you when firstly log in the system. You can add several users and set right for them through the function of ―Set Account Right‖. 11.
49 NVMS-1000 User Manual If you have checked ―Default Permission‖ under initial permission when creating new account, all the resource permissions and system permissions will be added for the user Change Account In the interface of User Management, select a user and click button to enter the interface. You can change account name, password, e-mail address, etc. according to need. Delete Account In the interface of User management, select a user and click button to delete it . 11.
50 NVMS-1000 User Manual Device Permission Click “Device Permission” to enter the interface. Select the right on the right hand you want to enjoy. E-map Permission Click “E-map Permission” to enter the interface. Add map permission for the selected user. System Permission Click “System Permission” to enter the interface, you can set the right of broadcast , searching log information and exporting it for the user you selected.
51 NVMS-1000 User Manual 12 Basic In the interface of control panel, click “Basic” to enter the interface. System startup and maintenance, backup and restore will be introduced in this chapter. Partition and Path configuration have been introduced in the above chapter, there we do not repeat again. 12.1 System Startup and Maintenance In the interface of Basic Configuration, click ―System Startup and Maintenance” to enter the interface.
52 NVMS-1000 User Manual 12.2.1 Backup System Configuration data In the interface of Basic Configuration, click “Backup System Configuration Data” to export the configuration data. 12.2.2 Restore System Configuration Data In the interface of Basic Configuration, click “Restore System Configuration Data” to import the configuration data. 12.3 Manually Output Trigger the Alarm In the control panel, click “Manual Alarm Output” under Basic Configuration to enter the interface.