SWT2 Sand & Water Sensory Center Assembly Guide SWT2_2018_A Check out our other products online at www.copernicused.com WARNING Please Recycle For assistance, please contact us: 1-800-267-8494 Email info@copernicused.com Have your packing slip ready for reference This product is meant to be assembled by an adult. In its unassembled state, small parts present a hazard. To be used under direct supervision of an adult. SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Sand & Water Sensory Center SWT2 Assembly Guide SWT2_2018_A Check out our other products online at www.copernicused.com For assistance, please contact us: 1-800-267-8494 Email info@copernicused.com Have your packing slip ready for reference Dear Educator, Thank you for purchasing one of our products. I hope that the Sand and Water Table is useful in your classroom. If you have any questions, concerns, or ideas please contact us by telephone at 1-800-267-8494 or email at info@copernicused.com.
Warning! Hazard Risks! Please read the warnings below for important safety information regarding your product. Failure to read these warnings or to follow the instructions below could result in personal injury or damage to your product that could void your warranty. Small Parts In its unassembled state, this product contains parts that can be hazardous to small children. This product should be assembled by an adult. This product is to be used under the supervision of an adult.
SWT2 Sand & Water Sensory Center - Parts Before beginning, you should have: Additional tools required: Adjustable Wrench x2 Hardware Contents - Box 1 Actual Size Long Side Frame x2 End Frame x2 Long Stretcher x2 Middle Stretcher x1 In Box 1 A M6x35mm Bolt 6x B M6x40mm Bolt 6x C M6x50mm Bolt 8x Middle Channel x1 Tub Wire Support x2 D M6 Barrel Nut 8x Side Channel x2 E M6 Lock Washer Lid x2 20x G Contour Washer 20x 40 lbs Weight Limit 4” Twin Wheel Locking Caster x4 Really Big Tub x2 F
SWT2 Tips for Assembly Watch for These Helpful Symbols This symbol denotes a 2 Person Task. For safety, please ensure that there are the suggested number of people working on steps displaying this symbol. 2-Person Task Watch for this symbol throughout the Assembly Guide. Wherever you see it, pay close attention. The symbol denotes a step needing extra attention to ensure it is done correctly. ! The star symbol highlights an advisory note.
SWT2 Sand & Water Sensory Center - Tips Before you being, Pay attention to assembly tips located throughout the assembly guide. Tip 1) Assemble Front Frame with holes facing same side ! ANGLED HOLE MUST FACE SAME SIDE ! ANGLED HOLE MUST FACE SAME SIDE Tips video available here: http://copernicused.com/assembly-tips.aspx ... start assembly on next page 6 SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Actual Size: 1 B E M6x40mm Bolt x4 M6 Lock Washer x4 G Contour Washer x4 You will need: (Not to Scale) Long Side Frame x2 Long Stretcher x2 Assemble Two Front Frames Build x2 Labels face outside B E G G Top Note the orientation of these holes, they must face the same side Bottom 7 SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
SWT2 Tip 2) ! 8 Sand & Water Sensory Center - Tips When assembling unit make sure frame holes face outwards on both sides. ANGLED HOLE MUST FACE OUTWARDS ! ANGLED HOLE MUST FACE OUTWARDS SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Actual Size: C 2 E M6x50mm Bolt x8 D M6 Barrel Nut x8 M6 Lock Washer x8 You will need: (Not to Scale) Front Leg Assembly x2 End Frame x2 2 Person F G M8 Lock Washer x8 Contour Washer x16 Attach End Frames Assemble the unit upside down. Do not fully tighten bolts until step 4 is complete. Small radius Label on top C G D G C E F F E G D G Large radius Note the orientation of these holes must be angled correctly. Floor Labels should always face outside.
SWT2 Tip 3) 10 Sand & Water Sensory Center - Tips Assembled frame should look like the following image. Shown with Tub Channels and Middle Stretcher. SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Actual Size: 3 A E M6x35mm Bolt x6 M6 Lock Washer x6 You will need: (Not to Scale) Side Channel x2 Middle Channel x1 2 Person Install Middle and Side Channels Do not fully tighten these bolts yet A E Note Channels face inward Actual Size: 4 You will need: (Not to Scale) B E M6x40mm Bolt x2 M6 Lock Washer x2 Middle Stretcher x1 2 Person Install Middle Stretcher B E 11 SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Actual Size: 5 H M12 Lock Washer x4 You will need: (Not to Scale) I M12 Washer Caster Wrench x4 4” Twin Wheel Locking Caster x4 x1 Leg Extension (OPTIONAL) x4 Determine your desired overall height and install casters 18” Tall Sand & Water Sensory Center I H Tighten! OR 24” Tall Sand & Water Sensory Center I H 12 SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Actual Size: 6 You will need: (Not to Scale) Really Big Tub x2 Tub Wire Support x2 15 lbs Weight Limit (shown with Leg Extensions installed) Install Tubs 1 2 Note the orientation of the Tub Wire Support Actual Size: 7 You will need: (Not to Scale) Main Tub x1 124 lbs Weight Limit of Water 252 lbs Weight Limit of Sand (6 x 42lbs / 18kg Sand bags) Verify Rubber Gasket Is Pre-installed on Tub Make sure rubber gasket is seated in place. Note because of its shape it is visible from the top & bottom.
You will need: (Not to Scale) 8 Drain, Drain Plug, Washer Drain Hose x1 Wrench x1 Choose Drain Fittings Make sure your hose faces the direction shown below. Tip: Apply soap to get fitting through washer Use the plug to keep sand out of drain. Use as backup only with water in case valve is accidently opened. Firmly tighten your fitting ! Tub drops into place for easy assembly Note your tub may rock from side to side at first when empty. Filling with sand / water will help it fit better.
Actual Size: 9 You will need: (Not to Scale) Lid x2 Using Your Lids You can use your Lids for activities such as Sand Etching when working with special needs students. You can store your Lids under the Main Tub like shown on the left. Use one lid as a shelf for other activities. You can also use your lids with the Really Big Tubs inside the Main Tub. 15 SWT2 - Version A - Released March 6, 2018 - Copernicus Educational Products Inc.
Actual Size: 10 You will need: (Not to Scale) Tips For Use Use Tubs to store sand & water toys. You can purchase additional Copernicus Really Big Tubs to separate different mediums, for example using sand AND water at the same time for easy cleanup. 15 lbs Weight Limit Part Number Contains: PTP-20 2 Blue Coloured Tubs PTP-21 2 Sand Coloured Tubs Use the two landings on the Main Tub as shelves for activities such as weighing with scales.