SWT2 Sand & Water Sensory Center Assembly Guide SWT2 _2015_A 1-800-267-8494 Check out our other products online at www.copernicused.com WARNING For assistance, please contact us: Email info@copernicused.com Have your packing slip ready for reference This product is meant to be assembled by an adult. In its unassembled state, small parts present a hazard. To be used under direct supervision of an adult.
SWT2 Sand & Water Sensory Center - Parts Before beginning, you should have: Additional tools required: Adjustable wrench Contents - Box 1 Hardware Long Side Frame 2x End Frame 2x Actual Size In Box 1 A M6x35mm Bolt 6x Long Stretcher 2x Middle Stretcher 1x B M6x40mm Bolt 6x C M6x50mm Bolt 8x Middle Channel 1x Tub Wire Support 2x D M6 Barrel Nut 8x E M6 Lock Washer G Contour Washer Side Channel 2x 20x Lid 2x 40 lbs Weight Limit 20x F M8 Lock Washer 8x 4” Caster With Brake & Safety Pinch Po
SWT2 Tips for Assembly - Using this Manual Watch for These Helpful Symbols l This symbol denotes a 2 Person Task. For safety, please ensure that there are two people 2 Person working on steps displaying this symbol l Watch for this symbol throughout the Assembly Instructions. Wherever you see it, pay close attention. The symbol denotes a step needing extra attention to ensure it is done correctly.
SWT2 Sand & Water Sensory Center - Tips Before you being, Pay attention to assembly tips located throughout the assembly guide. Tip 1) Assemble Front Frame with holes facing same side ! ANGLED HOLE MUST FACE SAME SIDE ! ANGLED HOLE MUST FACE SAME SIDE Tips video available here: http://copernicused.com/assembly-tips.aspx ... start assembly on next page SWT2 - Version A - Released 19 February 2015 - Copernicus Educational Products Inc.
Actual Size: 1 B E G M6x40mm Bolt x4 M6 Lock Washer x4 Contour Washer x4 You will need: (Not to Scale) Long Side Frame x2 Long Stretcher x2 Assemble Two Front Frames Build x2 Labels face outside B E G G Top Note the orientation of these holes, they must face the same side Bottom SWT2 - Version A - Released 19 February 2015 - Copernicus Educational Products Inc.
SWT2 Tip 2) ! Sand & Water Sensory Center - Tips When assembling unit make sure frame holes face outwards on both sides. ANGLED HOLE MUST FACE OUTWARDS ! ANGLED HOLE MUST FACE OUTWARDS Tips video available here: http://copernicused.com/assembly-tips.aspx SWT2 - Version A - Released 19 February 2015 - Copernicus Educational Products Inc.
Actual Size: 2 C E D M6x50mm Bolt x8 M6 Lock Washer x8 M6 Barrel Nut x8 F G M8 Lock Washer x8 Contour Washer x 16 You will need: (Not to Scale) 2 Person Front Leg Assembly x2 End Frame x2 Attach End Frames Assemble the unit upside down Do not tighten bolts yet! Small radius Label on top C G F E G D D G F C E G Large radius Floor Note the orientation of these holes must be angled correctly. Labels should always face outside. Unit is still flipped upside down.
SWT2 Tip 3) Sand & Water Sensory Center - Tips Assembled frame should look like the following image. Shown with Tub Channels and Middle Stretcher. Tips video available here: http://copernicused.com/assembly-tips.aspx SWT2 - Version A - Released 19 February 2015 - Copernicus Educational Products Inc.
Actual Size: 3 A E M6x35mm Bolt x6 M6 Lock Washer x6 You will need: (Not to Scale) Middle Channel x1 2 Person Side Channel x2 Install Middle and Side Channels Do not fully tighten these bolts yet A E Note Channels face inward Actual Size: 4 B E M6x40mm Bolt x2 M6 Lock Washer x2 You will need: (Not to Scale) Middle Stretcher x1 2 Person Install Middle Stretcher B Tighten ALL bolts now E SWT2 - Version A - Released 19 February 2015 - Copernicus Educational Products Inc.
Actual Size: 5 You will need: (Not to Scale) H M12 Lock Washer x4 4” Caster With Brake & Safety Pinch Point Cover x4 I M12 Washer x4 + Optional Leg Extension x4 Determine your desired overall height and install casters 18” Tall Sand & Water Sensory Center Remove the nut on the caster if assembling 18” version Tighten! I H Lock casters when installing OR Make sure the nut on the caster is fully threaded before installing the casters on 24” frame.
Actual Size: 6 You will need: (Not to Scale) 15 lbs Weight Limit Tub Wire Support x2 Really Big Tub x2 (shown with Leg Extensions installed) Install Tubs 1 2 Note the orientation of the Tub Wire Support Actual Size: 7 You will need: (Not to Scale) 124 lbs Weight Limit of Water 252 lbs Weight Limit of Sand (6 x 42lbs / 18kg Sand bags) Main Tub x1 Verify Rubber Gasket Is Pre-installed on Tub Make sure rubber gasket is seated in place. Note because of its shape it is visible from the top & bottom.
8 You will need: (Not to Scale) Drain, Drain Plug, Washer Drain Hose x1 Wrench x1 Choose Drain Fittings Make sure your hose faces the direction shown below. Tip: Apply soap to get fitting through washer Use the plug to keep sand out of drain. Use as backup only with water in case valve is accidently opened. Firmly tighten your fitting ! Tub drops into place for easy assembly Note your tub may rock from side to side at first when empty. Filling with sand / water will help it fit better.
Actual Size: 9 You will need: (Not to Scale) Lid x2 Using Your Lids You can use your Lids for activities such as Sand Etching when working with special needs students. You can store your Lids under the Main Tub like shown on the left. Use one lid as a shelf for other activities. You can also use your lids with the Really Big Tubs inside the Main Tub. SWT2 - Version A - Released 19 February 2015 - Copernicus Educational Products Inc.
Actual Size: 10 You will need: (Not to Scale) Tips For Use Use Tubs to store sand & water toys. You can purchase additional Copernicus Really Big Tubs to separate different mediums, for example using sand AND water at the same time for easy cleanup. 15 lbs Weight Limit Part Number Contains: PTP-20 2 Blue Coloured Tubs PTP-21 2 Sand Coloured Tubs Use the two landings on the Main Tub as shelves for activities such as weighing with scales.
SWT2 Sand & Water Sensory Center Assembly Guide SWT2 _2015_A Check out our other products online at www.copernicused.com For assistance, please contact us: 1-800-267-8494 Email info@copernicused.com Have your packing slip ready for reference Dear Educator, Thank you for purchasing one of our products. I hope the assembly of your Sand & Water Sensory Center went well.