USER MANUAL Battery Wireless Up-light Lithium
Contents Contents ............................................................................................................... 1 Disclaimer ............................................................................................................. 3 Product Modification ........................................................................................... 3 Safety Information................................................................................................ 3 Before You Begin ........
Mechanical.......................................................................................................... 15 Dimensions .................................................................................................... 15 Antenna .......................................................................................................... 15 Locking ........................................................................................................... 15 Warranty ...............................
Disclaimer CORE Lighting Limited believe the information in this manual is accurate and complete however assumes no responsibility for any error or omissions within this document or any other documentation accompanying the product. We reserve the right to revise this document at any time. Please see www.corelighting.co.uk/support to download latest version.
Before You Begin The CORE ColourPoint fixture is a battery-powered wireless up-lighter capable of providing portable and instant architectural and feature lighting anywhere. With high-powered red, green, blue and white LEDs the fixture is capable of producing any colour or shade of white using combinations of those LEDs. Ideal for illuminating buildings in colour, both indoors and outdoors, the fixture is powerful enough to light buildings of 3 or 4 storeys.
Getting Started ColourPoint Key Elements Carry handle Handle stowed LED Emitters Kensington lock point Shroud (silver) Charging & Mains PSU Port Battery charge indicator Padlock Fixing Charging Status LED WDMX button and LED indicator Power On/Off Power The battery charger may be included as an accessory for individually purchased fixtures or built into the flight case for multiple charging fixtures. In each case the supply has an input voltage range of 100-240 VAC at 50/60Hz.
Operation Power Push and hold this power button for >1 second to switch the unit ON or OFF The display will show “CORE Lighting” and software version for a few seconds before starting The display backlight will extinguish after a short time to reduce power use Charging Turn the unit OFF before connecting to the charger Only use the supplied charger or charging case External chargers should be plugged into the 5-pin connector on the front of the unit.
External Power (Optional Accessory) A separately available power supply is available as an accessory to drive the ColourPoint from mains voltage 100-250VAC 50/60Hz. Connect this to the charging/power port in the front of the unit. The device supplies 24VDC to the ColourPoint which replaces battery power. Battery is disconnected whilst the Power Supply is plugged in so will not be charged or discharged.
Function Modes There are three modes of Operation, accessed through the FUNCTION menu; Cust Col This mode allows the fixture to output a static Red, Green, Blue or White colour, or any combination thereof; each colour may be set to any value 0 to 255. Any W-DMX signal, if present, is ignored. Static In this mode the fixture outputs a static LEE or preset ‘cc’ colour as selected. The selection is remembered if the unit is switched off then back on or put into another mode.
Static Operation When in STATIC mode the display indicates the current selected colour. STATIC Lee345 To change the current selected colour press . The last character of the currently selected colour is underlined Use the keys to select a colour from the built-in library of 70 pre-programmed colours, including 60 popular LEE Filter Colours The colour changes when cycling through the available options. The selected colour is only saved when is pressed.
DMX Operation CORE ColourPoint is equipped with a Wireless Solution W-DMX wireless radio receiver. This allows the fixture colour to be set up by or synchronized with sequences produced by a DMX lighting controller. A compatible W-DMX transmitter attached to a DMX controller is necessary, available separately. This could be a lighting desk, a specific controller, or a CORE Point 15, 20 or 30 Master unit. DMX Addr: 001 When in DMX mode the display will show the current active DMX Start Address.
W-DMX Pairing and Unpairing ColourPoint units need to be manually paired with the lighting control unit equipped with a W-DMX transmitter. This could be a lighting desk with DMX Output, or a CORE Point15/20/30 Master unit with a W-DMX transmitter inside. This allows a group of ColourPoint fixtures to be controlled from the lighting desk or Point15/20/30 Master using the built-in colour cycles (Inside Point15/20/30). Or set up individually selected colours across many units at once from just one Master unit.
Pairing with a W-DMX Transmitter unit Switch on the ColourPoint. Ensure the ColourPoint is unpaired from any other transmitter (the LINK LED is OFF) – above. Ensure the transmitter is within range and switched on. Press its ‘FUNCTION’ button for more than 1s. The transmitter will scan for all unlinked receivers for around 10 seconds; the LED will flash. If pairing is successful the LINK LED on the ColourPoint will illuminate.
Additional Settings A number of additional settings may be accessed within the menu system: Power Mode Under the “CHANGE Settings” menu ColourPoint has two power modes that can be selected: Power LongLife Power Normal 50% Power Full Power The “Normal” option provides maximum light output at the cost of reduced battery life. “LongLife” reduces the LED output by 50%, therefore enables 2 x running period for ALL FUNCTIONS, whether stand-alone or DMX. To change the power mode press then press Use .
keys to select “SOFT DIMMER” and press Then use the Use the keys to toggle between “On” and “Off” and press to select. to save changes. The Soft Dimmer function only affects use in DMX mode. i Note the “Soft Dimmer Off” mode is compatible with Point15, Point20 and Point30 dimmer curves to ensure all CORE Lighting fixtures have the same behaviour when used on the same WDMX system. Keypad Lock The keypad may be locked to prevent tampering or inadvertent adjustment of the unit.
Mechanical Dimensions 253 287 174 Antenna The antenna is a high-gain type similar in performance to the Wireless Solutions W-DMX 2dB standard antenna according to testing. This antenna is now fitted to all CORE POINT units. Locking The unit may be locked to a nearby object by passing a locking wire or padlock through the locking holes in the top or bottom plates. A Kensington Lock point is also provided on the bridle assembly holding the head in place.
Warranty CORE Lighting Limited (CORE Lighting) warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below). CORE Lighting will repair or replace (at CORE Lighting's option) this product or any defective parts in this product. The standard warranty period is 24 months from date of purchase although this period may vary from country to country. If in doubt consult your dealer and ensure that you retain proof of purchase.
Compliance Information System Compliance CORE Lighting Limited declares that this product conforms to the specifications listed in this manual, following the provisions of the European R&TTE directive 1999/5/EC: Restrictions on Hazardous Substances (RoHS) (2002/95/CE) Electromagnetic Compatibility (2004/108/EC). Safety (EN 60950) Technical requirements for radio equipment. (EN 300 328) CAUTION—This equipment is intended to be used in all EU and EFTA countries.
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. RF Exposure Warning for North America, and Australia Warning! To meet FCC and other national safety guidelines for RF exposure, the antennas for this device must be installed to ensure a minimum separation distance of 20cm (7.9 in.) from persons.