CG-WLAPGMN Wireless108M Access Point User Manual
Contents WLAPGMN User Manual Regulatory Compliance............................................................................................... 2 1. Product Introduction................................................................................................ 3 1.1 Packing Content................................................................................ 3 1.2 Hardware Description..................................................................... 3 1.3 Features..............................
Regulatory Compliance WLAPGMN User Manual FCC Interference Statement This device complies with Part 15 of FCC rule. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation. This Broadband Wireless Router has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
1 Product Introduction WLAPGMN User Manual corega WLAPGMN is a high speed Wireless Access Point, which support IEEE 802.11b/g standard with speed up to 108 Mbps provide higher data rate and through is suitable for user who has high speed transmission requirement. corega WLAPGMN supports enhanced security Functions to protect your PCs from outside intruders. Its dual diversity antenna for using in multi-path environment to enhance the transmission quality. 1.
WLAPGMN User Manual 1. LAN LED (Green) On: Connected Blink: Transmitting or receiving data OFF: Disconnected 2. WLAN LED (Green) ON: Connected Blink: Transmitting or receiving data OFF: Disconnected 3. Power LED(Green) Indicate power configuration 4. Detachable Antenna Connector 5. LAN port Be connected with PC or Hub 6. Init buttom Press the buttom will recover to initial configuration 7. DC IN Socket Connect with power adapter 1.3 Features • Compatible with IEEE 802.11b and 802.11g standard.
Hardware Installation 2 WLAPGMN User Manual 2.1 Environment Requirements • A computer has configured TCP/IP • An availabe RJ-45 port on an Ethernet Hub/Switch/Router/Modem • A WLAN adapter which compliance with IEEE802.11g, IEEE802.11b, or IEEE802.11 standard. • Microsoft Internet Explorer 4.0 or Netscape Navigator 4.78 above browser. 2.2 Install the product (1) Prepare a hub/router which has connected with ADSL cable and PC. (2) Insert the cable connector into the LAN port of WLAPGMN.
WLAPGMN User Manual 2.
3 Setting WLAN Adapter WLAPGMN User Manual This section lead you to configure the settings of wireless LAN adapters installed in other computers to connect with WLAPGMN. There’re three situations show as below: 3.1 Setting up the Centrino in Win-XP(SP1) OS 1. From the [Start Menu], select [Settings] -> [Control Panel]-> [Network]-> double click [Wireless network connection]. 2.
WLAPGMN User Manual 3. Setting completed, it is available to surf on internet through WLAPGMN. 3.2 Setting up the Centrino in Win-XP(SP2) OS 1. From the [Start Menu], select [Settings] -> [Control Panel]-> [Network]->double click [Wireless network connection]. 2. In following screen, please select [corega] in the listing of available wireless networks, => click [Connect].
WLAPGMN User Manual 3. If the WLAPGMN has not enable the security function, it will show up below screen, click [Connect Anyway] to continue. * Note: 1. “corega” is the default ESSID of WLAPGMN, once ESSID in WLAPGMN has been changed, the ESSID in WLAN adapter has to be changed, too. 2. If the WLAPGMN has enabled security function, it will show below screen, you have to type the key which is consistant with WLAPGMN, => click [Connect]. 3.
WLAPGMN User Manual 3.3 Setting up corega WLAN adapter Following steps were taken corega WLCB54GS for instance: 1. Double click icon on system tray, and it will show up the utility screen. If there’s no icon appears on system tray, please press [Start] => [Programs]=>[corega CG-WLCB54GS]=> [Wireless LAN Utility]. 2. Please double click [corega] ESSID from [Available WLANs], then you’ll see it will be added in [Preferred WLANs] listing. 3. Now click [OK] then available to surf on internet by WLAPGMN.
4 Setting Utility Program WLAPGMN User Manual This section take Windows XP for instance. Before starting, you have to set up TCP/IP and web browser first. The steps as below: Step1. Setting TCP/IP 1. From the [Start Menu], select [Settings] => select [Control Panel]=>select [Network]=> select [Connections], => click and press right button of the mouse, and select [properties]. 2. In [General] tab, Please select [Internet Protocol (TCP/IP)]=> click [Properties].
WLAPGMN User Manual 3. Select both [Use the following IP address] and [Use the following DNS server addresses] (Recommended). Enter the IP address between 192.168.1.1~192.168.254 range (except 192.168.1.230); submask is 255.255.255.0=>click [Advanced]. 4. Return back to [Local Area Connection Properties] screen => click [OK] to close it. Step2. Setting Web browser 1. Double click [Internet Explorer] (This section take IE6.0 for instance)=> click [tools], and select [Internet Options.].
WLAPGMN User Manual 2. Click [Connections] tab=>select [LAN Settings]. 3. Please uncheck the three items in below screen (don’t select anyone)=> click [OK].
WLAPGMN User Manual 4. Please click [OK] to close the [Internet Options] screen. Step3. Setting Utility Program To make sure successful setting, please exit the virus and firewall program before setting the products. After setting completed, they can be opened again. 1. Double click the web browser (this section take IE6.0 for instance). 2. Type “192.168.1.230” in the address tab =>press enter. 3. It shows up the prompt box, type “root” in [user name] tab, and keep the [password] tab empty => click [OK].
WLAPGMN User Manual You are now in the utility program for setting, details as below: 4.1 Status 1. Select [Stauts], it will display all status for corega WLAPGMN. 4.2 Wizard (Quick Installation) This section will lead you quick installation. 1. Select [Wizard] => Press [Next].
WLAPGMN User Manual 2. You will see [SSID] and [Channel] in the following screen, you may change it or not, but recommanded to change it to make sure the security. ＊Note: the default SSID(ESSID) is "corega", and default channel is 6. 3. Recommanded to click [Enable] from WEP setting screen, => select [64Bits], [128Bits], or [152Bits]=> key in password in Key1 tab, => click [Next]. * Note: 1.
WLAPGMN User Manual 4. Setting completed, please press [Reboot] for saving the changes. 5. It will show up Saving screen, few seconds later, it will return to re-login prompt box. 6. Change the same ESSID for all WLAN adapters which connected to WLAPGMN. 4.3 Advanced 4.3.1 Configuration 1. Click[Advanced]->[Configuration]-[IP Address], once configure completed, please click [Apply].
WLAPGMN User Manual Item Description MAC Address Display corega WLAPGMN’s Mac address Get IP From There are 2 selections: Manual and DHCP * Default is [Manual]. IP Address Default is [192.168.1.230]. Subnet Mask Default is [255.255.255.0]. Default Gateway Default is [192.168.1.1]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. 1.
WLAPGMN User Manual Beacon Interval (20-1000) Default is [100], recommanded don't change it. DTIM (1-255) Default is [1], recommand don't change it. Fragmentation Enter even numbers. Length (256~2346) Default is [2346], recommanded don't change it. RTS Length (256~2346) Default is [2346], recommanded don't change it. Transmit Power Default is [full]. Super Mode If your Wireless LAN Card supports Super G Mode transmit rate. You can use this function to increase wireless throughput.
WLAPGMN User Manual Item Specification Authentication Once choosing WEP must select [Shared Key]; choosing WPA will directly click [OK] to go next step. * Default is [Open System]. Vaild Key Select one of default WEP Key groups First~Fourth. First Key ~ Fourth Key Please enter 10 characters for 64Bit; 26 characters for 128Bit or 32 characters for 512Bit (number 0~9, and letters a~f ). * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. B.
WLAPGMN User Manual 2. Enter 9~63 characters in [PassPhrase]->select [Cipher Type], once configure completed, click [Apply]. * Note: 1. Group Key Update Interval: enter a number to indicate the key exchanged per minute. 2. If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. ＊[WPA-EAP]: is suitable for enterprise with RADIUS server. 1. Click[Advanced]->[Configuration]->[Security Settings]->select [WPA] from [Authentication] tab-> click [Apply].
WLAPGMN User Manual 2. Enter 9~63 characters in [PassPhrase]->select [Cipher Type], setting [Security Server Settings] table, once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. 1. Click[Advanced]->[Configuration]-[Access Control Settings], once configure completed, click [Save].
WLAPGMN User Manual Item Description Control Disable: Disable the mac address filter function. Accept:Only connect with the mac address which list the table. Reject:Only conntect with the mac address which list the table. MAC Address Enter the mac address of the WLAN adapter which connected with computer.(character of 0~9; A~F) * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. 1.
WLAPGMN User Manual Internet Hub/Switch 2. P to MP Bridge Mode: each one set the same channel, different ESSID Click[Advanced]->[Configuration]->[AP Mode]->[PtMP Bridge]>enter Mac Address in [Remote AP MAC Address], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes.
WLAPGMN User Manual 3. Repeater Mode: each one set the same ESSID Click[Advanced]->[Configuration]->[AP Mode]->[AP Repeater]>enter Mac Address in [Root AP MAC Address]->configure [Site Survey], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. Internet LAN Hub/Switch Building Building 4. Client Mode Click[Advanced]->[Configuration]->[AP Mode]->[AP Client]-> enter the Mac address->click [Apply].
WLAPGMN User Manual * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. Internet Hub/Switch Click[Advanced]->[Configuration]->[WLAN Partition]->check the box, once configure completed, click [Apply].
WLAPGMN User Manual * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. Click[Advanced]->[Configuration]->[Device Information]->setting [System Name], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. 4.3.2 Management Click [Advanced]->[Management]->[Administration], once configure completed, click [Save]. ＊Notice: 1.
WLAPGMN User Manual Click[Advanced]->[Management]-[Misc], once configure completed, click [Apply]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. 4.3.3 Maintenance Click[Advanced]->[Maintaince]->[Update Firmware]>[Browse]=>select the path of the firmware file , =>click [OK]. * Note: If any setting has been changed, you have to click [Reboot]>[Restart] to save the changes. 1.
WLAPGMN User Manual 1. Click [Advanced]->[Maintenance]->[Restart System]->all new settings will be saved. 2. It will show up the Saving screen, several seconds later, it will return to re-login screen. * Note: • This function is the same as [Reboot]. • If any setting changes, please run this function to save and apply the changes. 1. Click[Advanced]->[Maintaince]->[Restore System]->system will restore to Factory Default Settings. 2.
WLAPGMN User Manual 4.4 Statistics The screen displays the statistics of throughput. 4.5 Reboot 1. Click [Reboot]->click [Restart], all new settings will be saved. 2. It will show up the Saving screen, severl seconds later, it will return to re-login screen. * Note: • This function is the same as [Advanced]->[Maintaince]->[Restart System]. • If any setting changes, please run this function to save and apply the changes.
5 FAQ WLAPGMN User Manual There are 2 ways for solving your problems: (1) First, please see following “FAQ” to check your problem. (2) Please go to http://www.corega-asia.com, click “Supports”=>select “Online Customer Support”, => fill in the form, =>click “submit”. We’ll reply you as soon as possible. Q1. Can't open the utility program. Ans: 1.Verify the computer has configured the TCP/IP, if yes, please verify the setting is correct (Please refer to [4. Step1. Setting TCP/IP]). 2.
WLAPGMN User Manual fire glass wall or door. It is to say to avoid the barriers between WLAPGMN and Wireless LAN adapter. 2. Shorten the distance between WLAPGMN and WLAN adapters. 3. Adjust the antenna direction. Q4. How to set/change the id and password for Utility Program? Ans: In utility program, Click[Advanced]->[Management]>[Administration], Setting the id and password. Q5. Forgot the Passowrd. Ans: Recommanded to initial the product setting, which method described as next question.
WLAPGMN User Manual * Once you forget the password or want to return to initial status, please run this function. * Details please refer to [chapter 5. FAQ-Q6]. Q7. How to get the latest firmware? Ans: Please go to http://www.corega-asia.com, =>click supports >download >select “firmware”, =>select and click the model which you want to upgrade. If you upgraded failure, you may restore the utility system to factory default settings, please refer Q6. Q8.
6 Specification WLAPGMN User Manual Standard LAN Interface Frequency Band Transmission method Modulation system Memory Capacity Transmission speed Coverage Area Channel Security Antenna Type Power Specification Support OS Support Application WLAN:IEEE802.11 IEEE802.11b IEEE802.11g LAN: IEEE802.3 IEEE802.3u IEEE802.3x 100BASE-TX/10BASE-T×1 RJ-45 port 2.4~2.5 GHz DS-SS/OFDM IEEE 802.11b: DBPSK, DQPSK, CCK IEEE 802.11g: BPSK, QPSK, 16-QAM, 64-QAM, OFDM 4 MB Flash ROM 16 MB SDRAM IEEE802.
About corega K.K. WLAPGMN User Manual corega K.K. designs, develops and markets professional networking products that address the specific needs of small and medium enterprises and home user’s easy-to-use, quality and reliable services of networking solutions requirements. Established in 1986, corega 100% founded by Allied Telesis Group in Yokohama, Japan. corega’s core products consists of 10/100/1000 Ethernet products, Wireless Networking Products(802.
www.corega-asia.com corega Taiwan Inc. 7F., No. 10, Lane 345, YangGuang St. Nei-Hu Chiu, Taipei City 114, Taiwan R.O.C. TEL: +886-2-8751-9164 FAX: +886-2-8751-9174 PN: S30-UM8201-00 Rev.
