N61.R5EK Piezo Motor Driven Rotation Stage User Manual Version: V1.0 N61.R5K This document describes the following products: ■ N61.R5E ■ N61.R5K N61.
DECLARATION Thank you for choosing Coremorrow's products! This user manual is applicable to N61.R5E/K Piezo Motor. For your smooth and correct use of this product, please read this manual carefully before use. Please follow the instructions in the manual installation and use procedures. Improper operation may cause injury to the operator or damage to the product.
Contents 1. Introduction ........................................................................................................................................2 1.1 Purpose and content ................................................................................................................2 1.2 Symbol and meaning................................................................................................................2 1.3 Expected reader .......................................................
N61.R5EK Piezo Motor Driven Rotation Stage User Manual 1. Introduction 1.1 Purpose and content The manual is mainly for your smooth and correct use of piezo motor. The manual contains all necessary information for N61.R5E/K. The manual describes the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. Attention: Improper handling can cause damage to the equipment. No order between items. 1. 2. Please operating in order. 1.
2. Safety Guide N61.R5E/K piezo motor is designed with advanced technology and safety standards, for safety and proper use of the product, please pay attention to following points when using: Temperature changed and pressure will charge the piezo motor. Piezo motor will remain charged for a period of time disconnected from the controller, so the operator should pay attention when using it: Do not disassemble N61.R5E/K piezo motor; Discharge N61.
N61.R5EK Piezo Motor Driven Rotation Stage User Manual 3. Product Overview 3.1 Product Introduction N61 piezo motor is a piezo motor direct-driven by piezo ceramics. It uses special mechanical structure design to convert linear microdisplacement by piezo ceramics into macro-angle rotation motion of mechanical platform. It has 360 ° rotary motion and has ultra-high rotation resolution. It is small in size and compact in structure, very suitable for integration. With E53.
4. Operating Environment Operating temperature: 0~50℃ Environment free of dust, clean, and non-corrosive substances Relative humidity: <60% 5. Installation and Operation Before installation, first check the safety, such as whether the cable is damaged or broken, and whether the power supply has grounding protection. 5.1 Installation and announcement Ensure that the installation surfacee is flat. Secure the piezo motor with M4 screws and tighten. Install the load and tighten it properly.
N61.R5EK Piezo Motor Driven Rotation Stage User Manual 5.2 Load When installing the load, ensure that the load mass is less than the max load of piezo motor, and install the load as much as possible at the center of the moving surface. The correct placement of the load is shown below: Load applied to the center of piezo motor For protection, we don't recommend the load is too high. If it is used a higher load, please reduce the position center of the load gravity.
Do not load longer loads and add to the side of the piezo motor If the screws used in tightening and connecting are too long, the screws will not be installed or some of screws will leak out, which will scratch the piezo motor and affect the motion accuracy. If the screws are too short, the connection will not be compact and easy to loosen. Looseness could damage the internal structure of the piezo motor.
N61.R5EK Piezo Motor Driven Rotation Stage User Manual Note: Slowly tighten the load when installing it, and the torque should not be too large to avoid damage to mechanism. Avoid stretching and bending cables. Please connect N61.R5E/K and controller with special cable provided by CoreMorrow. Please do not extend the cable without authorization, please contact us if you need a longer cable. 5.
6.2 Unpacking inspection Please check below information: Before opening the package, please carefully check the packaging for damage, bruising, wetting, moisture, deformation, etc. Please check the parts on a case-by-case basis based on the supply contract and the packing list. Whether there is obvious damage on the surface of the product. Whether the product identification is clear and complete. Whether the connector is loose, the connection line is broken or not, etc.
N61.R5EK Piezo Motor Driven Rotation Stage User Manual Please do not loosen the screws on the motor structure, avoiding to affect the accuracy. Daily cleaning: Please disconnect the piezo motor to controller, then clean the surface of it. When cleaning, first wipe a small amount of detergent with a towel and gently wipe the surface of the piezo motor, then wash it with alcohol. Please do not use ultrasonic waves for cleaning. 8.
