P11 Piezo Nanopositioning Stage User Manual Version: V1.0 This document describes the following products: ■ P11.X100S P11.X100K ■ P11.Z100S P11.Z100K ■ P11.XY100S P11.XY100K ■ P11.XZ100S P11.XZ100K ■ P11.XYZ100S P11.
DECLARATION Thank you for choosing Coremorrow's products! This user manual is applicable to P11 series piezo nanopositioning stage. For your smooth and correct use of this product, please read this manual carefully before use. Please follow the instructions in the manual installation and use procedures. Improper operation may cause injury to the operator or damage to the product.
Contents 1. Introduction ........................................................................................................................................2 1.1 Purpose and content ................................................................................................................2 1.2 Symbol and meaning................................................................................................................2 1.3 Expected reader .......................................................
P11 Piezo Nanopositioning Stage User Manual 1. Introduction 1.1 Purpose and content The manual is mainly for your smooth and correct use of piezo stage. The manual contains all necessary information for P11 series piezo stage. The manual describes the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. Attention: Improper handling can cause damage to the equipment. No order between items. 1. 2. Please operating in order. 1.
2. Safety Guide P11 piezo nanopositioning stage is designed with advanced technology and safety standards, for safety and proper use of the product, please pay attention to following points when using: Temperature changed and pressure will charge the piezo stage.
P11 Piezo Nanopositioning Stage User Manual 3. Product Overview 3.1 Product Introduction P11 series piezo nanopositioning stage has the following advantages: High performance piezo stack: P11 piezo stage is driven by high-performance piezo stack. The piezo stage is fully insulated, so its performance and service life are far superior to those of conventional stage. The insulating layer could effectively prevent the piezo stack from being damaged by moisture.
3.2 Product Features Quick response time; Closed-loop SGS sensor with high positioning accuracy; Mainly used for high frequency. 3.3 Motion direction Figure1.
P11 Piezo Nanopositioning Stage User Manual P11 connection mark and motion direction are as follows: Model Motion direction P11.X X P11.Z Z X P11.XY Y X P11.XZ Z X P11.
5.1 Installation and connection 1. Ensure that the installation plane is flat; 2. Secure the piezo stage with M2.5 screws and tighten; 3、Install the load and tighten properly to ensure positioning accuracy; 4、Connect the cable to the corresponding interface of the controller according to the connector head; Sensor connector PZT connector Figure2 connector P11 installation diagram is as follows: Load connection hole (M3 Screw) Moving part Fixed mounting hole (M2.
P11 Piezo Nanopositioning Stage User Manual 5.2 Load When installing the load, ensure that the load mass is less than the max load of the P11, and install the load as much as possible at the center of the moving surface. The correct placement of the load is shown below: Figure4 Load applied to the center of the stage For protection, we don't recommend the load is too high. If it is used a higher load, please reduce the position center of the load gravity.
If the screws used in tightening and connecting are too long, the screws will not be installed or some of screws will leak out, which will scratch the stage and affect the motion accuracy. If the screws are too short, the connection will not be compact and easy to loosen. Looseness could damage the internal structure of the stage.
P11 Piezo Nanopositioning Stage User Manual Note: Slowly tighten the load when installing it, and the torque should not be too large to avoid damage to mechanism; Avoid stretching and bending cables; Please connect P11 piezo nanopositioning stage and controller with special cable provided by CoreMorrow; Please do not extend the cable without authorization, please contact us if you need a longer cable. 5.
Note: Please do not remove the grounding protection during operation. If it needs to be temporarily removed, reconnect the grounding protection before starting again. Drive voltage should not exceed 150V; If abnormal noise or oscillation occurs during operating, immediately turn off the power check parameter setting. 6. Transportation and inspection 6.1 Transportation Piezo stage is packed in carton. The transportation is carried out under the condition of packaging.
P11 Piezo Nanopositioning Stage User Manual caused by bumps; Please do not use heavy tools or use rough methods to open them； Please do not discard all packaging materials for return shipments. 7. Maintenance and processing 7.1 Problem Processing Common problems are shown in the following table: Problem Description Possible reasons The cable is not connected correctly or is in faulty contact.
If the user has problems that could not be solved. Please record the fault situation and contact with us. The professional technical engineer would help solve the problem. Problems caused by improper operation are not covered by the warranty; CoreMorrow is not responsible for any problems caused by dismantling the peizo stage without permission. 7.
P11 Piezo Nanopositioning Stage User Manual 8. Connector 8.1 Driving and Sensor cable Driving cable interface is 1-contact LEMO, model number is LEMO ERA.00.250.CTL, as shown below: Figure9 1-contact LEMO Sensor cable interface is 4-contacts LEMO, model number is LEMO ERA.0S.304.
9.Customer Service If you have questions about the products you are currently using, please let us know the following information: Piezo stage model number and related number Controller model for this product Software driver version for this product Computer operating system for installing supporting software 10.Contact us Harbin Core Tomorrow Science & Technology Co., Ltd. Tel: +86-451-86268790 Email: info@coremorrow.com Website: www.coremorrow.com Address: Building I2, No.
