P73 Piezo Objective Scanner User Manual Version: V1.0 This document describes the following products: ■ P73.Z200S P73.Z200K ■ P73.Z500S P73.Z500K ■ P73.Z1000S P73.
DECLARATION This user manual is applicable to P73 Piezo Objective Scanner, for your smooth and correct use of this product, please read this manual carefully before using it. Please follow the instructions in the installation and use process.
Contents 1. Introduction ........................................................................................................................................2 1.1 Purpose and content ................................................................................................................2 1.2 Symbol and meaning................................................................................................................2 1.3 Users of This Manual ..................................................
P73 Piezo Objective Scanner User Manual 1. Introduction 1.1 Purpose and content This manual is mainly for your smooth and correct use of P73 Piezo Objective Scanner. The manual contains all the necessary information for P73 Piezo Objective Scanner. Introduction of the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. Attention: Improper handling can cause damage to the equipment. No order between items. 1. 2.
2. Safety Guide P73 Piezo Objective Scanner is designed with the most advanced technology and safety standards for your own safety and the correct use of the product, please observe the following points when in use. A change in temperature and pressure will charge the piezoelectric actuator, and the actuator will remain energized for a period of time when it is disconnected from the controller,So the operator should pay attention to when in use.
P73 Piezo Objective Scanner User Manual 3. Product Overview 3.1 Product Introduction P73 Piezo Objective Scanner has the following advantages: High performance piezo stack: P73 Piezo Objective Scanner is driven by a highly reliable ceramic actuator with a fully insulated structure, so its performance and service life are far better than the traditional actuator. The insulating layer can effectively prevent the piezoelectric ceramic from being damaged when exposed to moisture.
microscopes, widely used in a wide range of microscopic imaging, two-photon microscope and other fields. 3.2 Product Features Strain gauge sensor, high positioning accuracy. High focusing stability. Multiple adapter models are available. 3.3 Motion Direction Mounting thread Lead out Adapter FIG. 1 Motion Direction of P73 Piezo Objective Scanner 4.
P73 Piezo Objective Scanner User Manual 5. Installation and operation Safety check should be carried out before installation, such as whether the connection wire is damaged or broken, whether the drive power supply is grounded, etc. 5.1 Installation and Precautions Safety check should be carried out before installation, such as whether the connection wire is damaged or broken, whether the drive power supply is grounded, etc. Installation of P73 Piezo Objective Scanner is shown as following 1.
The wiring mode of LEMO connector is shown as below: Sensing label Sensing connector Driving connector Driving label FIG.3 Connector diagram 5.2 Load Please refer to the position to mount the load is shown below. FIG.4 The correct position to mount the load FIG.
P73 Piezo Objective Scanner User Manual When connecting the objective lens, it should be noted that the mass of the objective lens should not exceed the load capacity of P73, and the load should not be too long, so as to P73 may be damaged by oscillation. 5.3 Operating Please reconfirm the following information before turning on the power: The operating environment meets the operating environment requirements of P73. Fixed screws must be tightened.
6. Transportation and inspection 6.1 Transportation This product is packed in cartons. Transportation is carried out under the packaging conditions. This product can be transported by various means of transport under normal circumstances. In the process of transportation, direct rain and snow, corrosive substances, strong collision, extrusion, irregular placement and other improper behaviors should be avoided as far as possible. 6.
P73 Piezo Objective Scanner User Manual 7. Maintenance and Treatment 7.1 Problem Handling FAQ are shown in the table below.
7.2 Daily maintenance If the product is not used for a long time, please store it in a dust-free, well-ventilated, clean and non-corrosive indoor environment after packaging. In the daily maintenance, please do not loosen the bolts on the product structure, so as not to affect the movement accuracy of the product. Daily cleaning: Please disconnect the product from the controller before cleaning the surface of the product.
P73 Piezo Objective Scanner User Manual 8. Connector 8.1 Driving and Sensor Connector The driving connector adopts a 1-contact lemo connector. The model is LEMO era.00.250. CTL as shown below: FIG.6 1-contact lemo The sensor connector adopts the 4-contacts lemo, model LEMO ERA.0s.304.CLL, as showne below: FIG.7 4-contacts lemo The bridge connection mode and pin definition of strain gauge are as follows: FIG.
9.Customer Service If you have questions about the products you are currently using, please let us know the following information: Product model and relevant number The controller model Software driver version Computer operating system that installs supporting software 10.Contact us Harbin Core Tomorrow Science & Technology Co., Ltd. Tel: +86-451-86268790 Email: info@coremorrow.com Website: www.coremorrow.com Address: Building I2, No.
