P76 Piezo Objective Scanner User Manual Version: V1.0 This document describes the following products: ■ P76.Z50S/K ■ P76.Z100S/K ■ P76.Z50SA/KA ■ P76.
DECLARATION Thank you for choosing Coremorrow's products! This user manual is applicable to P76 series piezo objective scanner. For your smooth and correct use of this product, please read this manual carefully before use. Please follow the instructions in the manual installation and use procedures. Improper operation may cause injury to the operator or damage to the product.
Contents 1. Introduction ........................................................................................................................................2 1.1 Purpose and content ................................................................................................................2 1.2 Symbol and meaning................................................................................................................2 1.3 Expected reader .......................................................
P76 Piezo Objective Scanner User Manual 1. Introduction 1.1 Purpose and content The manual is mainly for your smooth and correct use of piezo objective scanner. The manual contains all necessary information for P76 piezo objective scanner. The manual describes the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. Attention: Improper handling can cause damage to the equipment. No order between items. 1. 2.
2. Safety Guide P76 piezo objective scanner is designed with advanced technology and safety standards, for safety and proper use of the product, please pay attention to following points when using: Temperature changed and pressure will charge the piezo objective scanner. It will remain charged for a period of time disconnected from the controller, so the operator should pay attention when using it: Do not disassemble P76 piezo objective scanner.
P76 Piezo Objective Scanner User Manual 3. Product Overview 3.1 Product Introduction P76 Piezo objective scanner has the following advantages: High performance piezo stack: P76 is driven by high-performance piezo stack. It is fully insulated, so its performance and service life are far superior to conventional actuator. Insulating layer can effectively prevent piezo stack from being damaged by moisture. Stability of piezo stack could be ensured under extreme conditions.
3.3 Motion direction Lens adapter Cable connector Motion Fixed screw thread Figure 1. P76 Piezo Obejctive Scanner 4. Operating environment Operating temperature: -20~80℃ Environment free of dust, clean, and non-corrosive substances Relative humidity: <60% Recommended voltage between 0 and 120V for long-term and high-reliability operation.
P76 Piezo Objective Scanner User Manual 5. Installation and operation 5.1 Installation and connection Before installation, first check the safety, such as whether the cable is damaged or broken, and whether the power supply has grounding protection. Installation steps of P76, as follows: 1. Screw the corresponding objective lens into the P76 objective scanner and tighten; 2. Screw the lens into the adapter and tighten; 3. Fix the installed piezo objective scanner and microscope connection section.
The connection method of the LEMO connector is shown in the following figure: Sensor connector PZT connector Figure3. Connector 5.2 Loading Connect the load according to the placement method described below, as shown in the figure below: Figure4. Correct loading method Figure5.
P76 Piezo Objective Scanner User Manual When connecting the objective lens, pay attention that the quality of the objective lens does not exceed the maximum allowable load of P76, and the load is not too long, otherwise it is easy to cause oscillation and damage P76. 5.
improper behavior such as squeezing, irregular placement. 6.2 Unpacking inspection Please check below information: Before opening the package, please carefully check the packaging for damage, bruising, wetting, moisture, deformation, etc.
P76 Piezo Objective Scanner User Manual Internal structure of the P76 is maintenance-free. Please do not loosen the screws on the product structure to avoid affecting the accuracy of the product. Daily cleaning: Please separate the product from the controller before cleaning the product surface. When cleaning, first use a towel dipped in a small amount of detergent to gently wipe the surface of the product, and then clean it with alcohol. Do not use ultrasonic cleaning.
LEMO Sensors Connector: Figure8. 4-contacts LEMO sensor connector 9.
P76 Piezo Objective Scanner User Manual 10.Contact us Harbin Core Tomorrow Science & Technology Co., Ltd. Tel: +86-451-86268790 Email: info@coremorrow.com Website: www.coremorrow.com Address: Building I2, No.
