Linear Piezo Nanopositioning Stage User Manual Version: V1.
DECLARATION Thank you for choosing Coremorrow's products! This user manual is applicable to linear piezo nanopositioning stage. For your smooth and correct use of this product, please read this manual carefully before use. Please follow the instructions in the manual installation and use procedures. Improper operation may cause injury to the operator or damage to the product.
Contents 1. Introduction ........................................................................................................................................2 1.1 Purpose and content ................................................................................................................2 1.2 Symbol and meaning................................................................................................................2 1.3 Expected reader .......................................................
Linear Piezo Nanopositioning Stage User Manual 1. Introduction 1.1 Purpose and content The manual is mainly for your smooth and correct use of piezo products. The manual contains all necessary information for linear piezo nanopositioning stage. The manual describes the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. Attention: Improper handling can cause damage to the equipment. No order between items. 1. 2.
2. Safety Guide Linear piezo nanopositioning stage is designed with advanced technology and safety standards, for safety and proper use of the product, please pay attention to following points when using: Temperature changed and pressure will charge the piezo product.
Linear Piezo Nanopositioning Stage User Manual 3. Product Overview 3.1 Product Introduction This linear piezo nanopositioning stage is piezoelectric screw motion platform, with a combination of linear motor piezoelectric screws and a sliding stage, and the highprecision motion of the piezoelectric screw is used to control the movement of the sliding stage. Two dimensional or three-dimensional motion control can be formed with multiple piezoelectric screw motion platforms. 3.
4. Operating Environment Operating temperature: 0~50℃ Environment free of dust, clean, and non-corrosive substances Relative humidity: <60% 5. Installation and Operation Before installation, first check the safety, such as whether the cable is damaged or broken, and whether the power supply has grounding protection. 5.1 Installation and announcement Load connection(M3) Lock knob Moving part 移动机构 Load connection(M6) Fixed mounting(M6) 1.
Linear Piezo Nanopositioning Stage User Manual 5.2 Load When installing the load, ensure that the load mass is less than the max load of piezo stage, and install the load as much as possible at the center of the moving surface. The correct placement of the load is shown below: Load applied to the center of piezo stage For protection, we don't recommend the load is too high. If it is used a higher load, please reduce the position center of the load gravity.
Do not load longer loads and add to the side of the piezo stage If the screws used in tightening and connecting are too long, the screws will not be installed or some of screws will leak out, which will scratch the piezo stage and affect the motion accuracy. If the screws are too short, the connection will not be compact and easy to loosen. Looseness could damage the internal structure of the piezo stage.
Linear Piezo Nanopositioning Stage User Manual Note: Slowly tighten the load when installing it, and the torque should not be too large to avoid damage to mechanism. Avoid stretching and bending cables. Please connect linear piezo nanopositioning stage and controller with special cable provided by CoreMorrow. Please do not extend the cable without authorization, please contact us if you need a longer cable. 5.
6.2 Unpacking inspection Please check below information: Before opening the package, please carefully check the packaging for damage, bruising, wetting, moisture, deformation, etc. Please check the parts on a case-by-case basis based on the supply contract and the packing list. Whether there is obvious damage on the surface of the product. Whether the product identification is clear and complete. Whether the connector is loose, the connection line is broken or not, etc.
Linear Piezo Nanopositioning Stage User Manual Please do not loosen the screws on the stage structure, avoiding to affect the accuracy. Daily cleaning: Please disconnect the piezo stage to controller, then clean the surface of it. When cleaning, first wipe a small amount of detergent with a towel and gently wipe the surface of the piezo stage, then wash it with alcohol. Please do not use ultrasonic waves for cleaning. 8.