Installation manual

ManualsBrandsCornelius ManualsIce Maker2000 - Series

IMPORTANT:

TO THE INSTALLER.

It is the responsibility of

the Installer to ensure that

the water supply to the

dispensing equipment is

provided with protection

against backflow by an air

gap as defined in

ANSI/ASME A112.1.2-1979;

or an approved vacuum

breaker or other such

method as proved effective

by test.

Water pipe connections

and fixtures directly

connected to a potable

water supply shall be

sized, installed, and

maintained according to

Federal, State, and Local

Codes.

COUNTERTOP ICEMAKER

IMD SERIES

Installation Manual

PRINTED IN U.S.A

IMI CORNELIUS INC; 94-2000

IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234

Telephone (800) 238-3600 Facsimile (612) 422-3246

Part No. 638085277

Revisied October 16, 2000

Revision B

THIS DOCUMENT CONTAINS IMPORTANT INFORMATION

This Manual must be read and understood before installing or operating this equipment

Distributed By:

Commercial Refrigeration Service, Inc.

WWW.WorldRestaurantSupply.COM

toll free (866) Ice Maker

(623) 869-8881

Summary of content (66 pages)

PAGE 1
IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234 Telephone (800) 238-3600 Installation Manual COUNTERTOP ICEMAKER IMD SERIES Facsimile (612) 422-3246 Distributed By: Commercial Refrigeration Service, Inc. WWW.WorldRestaurantSupply.COM toll free (866) Ice Maker (623) 869-8881 IMPORTANT: TO THE INSTALLER.
PAGE 2
TABLE OF CONTENTS Page SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 RECOGNIZE SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 UNDERSTAND SIGNAL WORDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FOLLOW SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CO2 (CARBON DIOXIDE) WARNING . . . . . . . . . . . . . . . . . . . . .
PAGE 3
TABLE OF CONTENTS (cont’d) Page TROUBLESHOOTING GEAR MOTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 THE GEARMOTOR WILL NOT RUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 THE GEARMOTOR STARTS BUTS TRIPS REPEATEDLY ON THE OVERLOAD PROTECTOR: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 THE MOTOR RUNS BUT OUTPUT SHAFT DOES NOT ROTATE: . . . . . . . 17 OVERLOAD CHECK: . . . . . . . . . . . . . . . . . . . .
PAGE 4
TABLE OF CONTENTS (cont’d) Page FIGURE 12. PIN NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 FIGURE 13. GEAR MOTOR OVERLOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 FIGURE 14. SCHEMATIC IMD 300–15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 FIGURE 15. SCHEMATIC IMD 300–30, IMD600–30, IMD601–30, IMD600–90, AND IMD601–90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
TABLE OF CONTENTS (cont’d) Page FIGURE 41. GEAR MOTOR ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 FIGURE 42. GEAR MOTOR ASSEMBLY WIRING DIAGRAM (ALL VOLTAGES) EXPLODED VIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 LIST OF TABLES SPECIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TEMPERATURE/PRESSURE CHARTS . . . . . . . . . . . . . . . .
PAGE 6
SAFETY INFORMATION Recognize Safety Information This is the safety-alert symbol. When you see this symbol on our machine or in this manual, be alert to the potentially of personal injury. Follow recommended precautions and safe operating practices. Understand Signal Words DANGER A signal word - DANGER, WARNING, OR CAUTION is used with the safety-alert symbol. DANGER identifies the most serious hazards. WARNING Safety signs with signal word DANGER or WARNING are typically near specific hazards.
PAGE 7
CAUTION: Unit requires a separate electrical line. See Manual for proper fuse size. WARNING: There Must Be Adequate Clearance Around Ice Maker. Allow Minimum 6” Air Intake and 4” For Air Exhaust on all sides and open to the front. NOTICE Unit must be installed per local plumbing and electrical codes. See Installation Manual for unit requirements. Failure to do so may cause damage to unit, which would void the warranty.
PAGE 8
SPECIFICATION CHART Models Condensing Unit VAC Hz Ph Comp RLA Fan Amps Grmtr Amps Refrigerant Oz. Type Circuit Fuse IMD300–15A Air Cooled 115 60 1 6 0.82 2 12 R134a 15 IMD302–15A Air Cooled 220/240 50 1 3 0.5 1.6 12 R134a 15 IMD300–30A Air Cooled 115 60 1 10.1 1 2 28 R404A 20 IMD300–30W Water Cooled 115 60 1 10.1 N/A 2 13 R404A 20 IMD301–30A Air Cooled 208/230 60 1 5.7 1 1.6 28 R404A 20 IMD301–30W Water Cooled 208/230 60 1 5.7 N/A 1.
PAGE 9
SHIPPING WT. 189 LBS. (APPROX.) FIGURE 1. DIMENSION DRAWING (15 LB.
PAGE 10
SHIPPING WT. (IMD300–30) 220 LBS. (APPROX.) SHIPPING WT. (IMD600–30) 240 LBS. (APPROX.) FIGURE 2. DIMENSION DRAWINGS (30 LBS.) IMD300–30 AND IMD600–30 SHIPPING WT. 225 LBS. (APPROX.) FIGURE 3. DIMENSION DRAWINGS (90 LBS.
PAGE 11
INSTALLATION INSTRUCTIONS A.. REMOVE ICEMAKER FROM CARTON: 1. Keep unit in the upright position, remove carton and pallet from unit and inspect unit for damage. Upon inspection of unit, if any damage is found, file a claim with carrier immediately. 2. Locate Startup Card either on outside of container or on plastic liner. Fill in proper information and send one copy to factory, and other copy to Distributor. Postage is prepaid. B.. CABINET REMOVAL 1.
PAGE 12
NOTE: Unit must be installed per local electrical code. F.. DRAIN CONNECTION 1. Install splash panel on machine and hold in place with (2) screws. Do not tighten at this time. 2. Remove drain tray mounting bracket from their shipping carton. 3. Clip the drain tray mounting bracket onto the bottom of the splash panel in the brackets provided. 4. Hook the drain tray into the splash panel and onto the mounting bracket. 5. Push the drain elbow securely onto the drain tray. Do not glue in place. 6.
PAGE 13
Low Water Safety Control – Adjust magnet by bending magnet arm as shown in figure 1 to shut down unit if the water level drops below the line on the side of the reservoir. Bin Control – Remove four screws from top of bin cover and lift cover so bin control plate can be manually lifted until unit shuts down. Release plate and unit will restart (On IMD300–30, IMD600–30 and IMD600–90 the dispense button must be depressed for 45 seconds before unit will start). Replace screws.
PAGE 14
GUIDE TO SERVICE ICEMAKER CLEANING AND SANITIZING PROCEDURES Do not use any of the ice made during cleaning operations. Clean and sanitize ice storage area when cleaning icemaker. 1. Turn machine off. 2. Shut off water supply. 3. Remove ice from storage bin. 4. Mix approved cleaner (2 gallons as directed). Recommended cleaner: Calgon Corp. of Virginia Chemicals, ice machine cleaner. Mixture: 3-1/3 ounces per gallon of water. Do not use nickel safe cleaners. 5.
PAGE 15
4. Check safety circuits for proper operation. 5. Check refrigeration system (see page12 12). 6. Check unit for abnormal noise. Tighten machine and cabinet screws, if necessary. 7. Check white upper bearings on auger assembly. If bearings are less than 1/16Ȃ thick, replace. See Figure 5 REPLACE 1/16Ȃ OK 1/16Ȃ OK REPLACE FIGURE 5. UPPER BEARING AND AUGER ASSEMBLY NOTE: 638085277 preventive maintenance can increase the trouble–free life of your ice maker.
PAGE 16
WATER LEVEL CONTROL HOW WATER LEVEL CONTROL WORKS When water is introduced through the inlet fitting the float rises. the float pushes against a lever which in turn forces the poppet assembly against the inlet fitting valve seat which seals the water off, (See Figure 4). Before the water inlet is sealed the safety switch is operated. In the event of a water failure the float would drop down and operate the safety switch to shut off the machine.
PAGE 17
The operating positions of the switch are fixed, no adjustments are necessary. If switch replacement becomes necessary, simply disconnect cable at connector, remove wires from switch. TEMPERATURE / PRESSURE CHARTS* $ 10 lbs.
PAGE 18
Use general refrigeration system practices when replacing and recharging unit. After new valve is in place, go through previous monitored adjustments and troubleshooting to be sure valve is functioning properly. NOTE: valve. On water cooled units adjust condenser modulating valve before troubleshooting expansion CAUTION: Very high discharge pressure is present in system. Quick disconnects on your gages will minimize Danger and loss of refrigerant.
PAGE 19
6. Recharge unit with refrigerant per nameplate. 7. Turn power and water On to unit. 8. With unit running adjust modulating valve to proper setting. 9. Go through a complete system check. GEAR MOTOR The gear motor is equipped with a start relay and a manual reset overload. When current is applied, the relay energizes and completes the circuit to the start winding. The motor reaches a predetermined speed and the relay drops out, disconnecting the start winding.
PAGE 20
AUGER & EXTRUDING HEAD REMOVAL 1. Disconnect unit from power supply. 2. Remove storage container cover and put aside. 3. Turn off water supply to icemaker. 4. After ice has melted from head take hold of the auger nut and lift straight up to disengage from icemaker. 5. When replacing the auger assembly, make certain that both the auger engages the output shaft drive and the extruding head ribs engage the evaporator tube collar. See Figures 8.
PAGE 21
TO REPLACE BEARINGS 1. Dispense all ice from unit. 2. Disconnect unit from electrical power. 3. Remove panels. 4. Unplug Dispense Motor and Ice Level Switch. 5. Remove four screws holding dispense cover in place. 6. Remove dispense cover assembly. 7. Use an open end wrench on auger nut connected to bearing and turn and turn counterclockwise to remove assembly. 8. Remove worn bearings. Replace with new bearings and then reinstall assembly.
PAGE 22
OVERLOAD CHECK – FIGURE 10. 4. Using a volt–ohm meter check the continuity across the overload, contacts #1 & #3. If none, wait for unit to cool down and try again. If still no continuity, the overload protector is defective and should be replaced. COMPRESSOR CHECK – FIGURE 11. The resistance readings on the windings will be between 0.25 and 10.00 ohms, a meter capable of these low readings must be used. 5. Check between ”C” & ”R.” Replace compressor if there is no continuity as the run windings are open.
PAGE 23
2. Remove motor end bell and stator, if necessary. 3. Check terminals 1 and 3 on overload. No continuity replace overload. Use a volt–ohm meter. See Figures 10 and NO TAG NOTE: Gear motor and related components can be checked from Pin Connector. See Figures 10 and NO TAG. MOTOR CHECK: The resistance readings on the windings will be between 5 to 25 ohms. A meter capable of these low readings must be used. The Start Relay cover must be removed. If no continuity on start or run winding test, replace stator.
PAGE 24
SAFETY CONTROLS Your Icemaker unit has several safety and control devices incorporated into its design. WARNING: None of the below described devices should ever be ”bypassed” to allow the unit to function. The safety and control system shut–off devices are: FIGURE 13. GEAR MOTOR OVERLOAD 1. Low water shut off reed switch located in icemaker float assembly. (Automatic reset type). 2. Gear motor thermal overload, manual reset type (red button on motor). See Figure 12. 3.
PAGE 25
GUIDE TO GOOD ICE CUSTOMER COMMENTS CHECK ICEMAKER LOCATION CONDITIONS FIRST “It runs but the ice is too soft.” S Proper air flow for condensing system. “The icemaker is not producing enough ice.” S Location too close to high units such as coffee urns, deep fryers, grills, etc. “The ice is too wet.” S Supply water conditions Water too warm (above 90_F). Water artificially softened above 262 ppm sodium chloride. Normal water supply too high in total dissolved solids (above 500 PPM).
PAGE 26
TROUBLESHOOTING CHART – ICEMAKER NOT OPERATING NO POWER Check electrical wiring in control box for loose connections. Check for failed service switch or relay. Check power to machine. LOW WATER SAFETY SWITCH OPEN ICEMAKER RUNS BUT DOES NOT MAKE ICE Dispense Timer Keeping Icemaker Off Check line voltage. Check compressor winding & components. Evaporator water tube may have an air bubble. Clear air bubble from tube. Too much refrigerant in system. 21 Evacuate and recharge system. Clean condenser.
PAGE 27
638085277 NOT USED WITH DRINK FRONT OPTION BLACK ONLY ON DRINK 5 4 3 BLACK 6 ILLUM. MERCH. FRONT OPTION LIGHT OPTION 1 WATER ICE SELECTOR SELECTOR LIGHT 2 2 PINK TAN BLACK 4 1 DRINK FRONT OPTION 24V WATER VALVES TRANSFORMER SOLENOID ICE LOW LEVEL WATER 1 I BI-METAL BROWN HEATER C S R START WHITE FAN CAP. S 22 SERVICE SWITCH M RUN 2 YELLOW START BLACK GROUND YELLOW 3 ANTI- GROUND 1 FREEZE START L DISPENSE SOLENOID 3 BLACK GROUND RED BLUE 3 DISP.
PAGE 28
23 638085277 FIGURE 15.
PAGE 29
638085277 24 FIGURE 16.
PAGE 30
2 1 3 5 10 8 9 4 7 6 FIGURE 17. IMD 300–15 CABINET PARTS ASSEMBLY AND PARTS LIST ITEM NO. 1 2 3 4 5 6 7 8 9 10 * * Not Shown PART NO. DESCRIPTION 638032724 638032731 638032721 638032768–002 638032768–001 638032722–005 638032715–007 638032715–006 638032766 638032765 638032729 638032725 638032822 638038588 638038589 638032785 638032818 Panel – Left Side Panel – Top Panel – Right Side Splash Panel Asmb – Push Button Splash Panel Asmb – Lever Spl.
PAGE 31
2 1 3 5 4 11 7 8 9 10 6 FIGURE 18. IMD300–30 AND IMD600–30 CABINET PARTS ASSEMBLY AND PARTS LIST ITEM NO. PART NO.
PAGE 32
2 1 3 5 7 8 9 4 10 6 FIGURE 19. IMD600–90 CABINET PARTS ASSEMBLY AND PARTS LIST ITEM NO. 1 2 3 4 * 5 * 6 7 * 8 9 10 * * PART DESCRIPTION NO. 638032539 638032537 638032538 638032040–006 638032541–001 638032536–002 638032536–001 638032548 638059270 638058805 638032531 638033508 638033509 638032531–001 638038588 638006529 638038589 638011601 638008315 638011643 638031162 638009627 638032287 638032136 638083373 Panel – Left Side Panel – Top Panel – Right Side Panel Splash Asm.
PAGE 33
9 10 13 8 14 15 16 7 18 22 19 2 23 1 17 12 3 4 638085277 6 FIGURE 20.
PAGE 34
REFRIGERATION AND FRAME ASSEMBLY IMD 300-15 PARTS LIST ITEM NO. 1 2 3 4 *5 6 7 8 9 10 *11 12 13 * *14 *15 *16 17 18 19 20 21 22 23 PART NO.
PAGE 35
9 8 11 7 6 2 1 10 3 10 638085277 FIGURE 21.
PAGE 36
REFRIGERATION AND FRAME ASSEMBLY IMD 300–30 AND IMD 600–30 PARTS LIST ITEM NO. 1 2 3 4 * 5 * * 6 7 8 9 * 10 * * 300–30 11 (see note) * * * * * PART NO.
PAGE 37
3 4 5 7 9 1 2 8 638085277 FIGURE 22.
PAGE 38
REFRIGERATION AND FRAME ASSEMBLY IMD 600–90 PART LIST ITEM NO. 1 PART NO. 638036273 638036272 638090635 638090630 638090630–001 638090630–002 638090236 90236–001 90236–002 638090009 638096723 638032545 638090625 638090625–002 638090021 638009755 638008943 08943–002 08943–002 638031832 31763–002 2 3 4 5 6 7 8 * * * * * * * 9 * * * 600–90 638090221 638090222 638090224 638090223 90221–001 638004393 DESCRIPTION Condenser, Air Cooled Condenser, Water Cooled Shroud, Condenser Front End Asm.
PAGE 39
3 2 1 5 6 4 7 FIGURE 23. WATER CONTROL ASSEMBLY AND PARTS LIST PART NO. 04643-04 IMD 300-30 AND IMD 600-30 ITEM NO. 1 PART NO.
PAGE 40
2 3 1 4 5 FIGURE 24. WATER CONTROL ASSEMBLY AND PARTS LIST PART NO. 32843 IMD 300–15 32545 IMD 600-90 ITEM NO. 1 PART NO.
PAGE 41
2 NO TAG 13 4 3 GROUND 8 1 6 7 12 9 11 10 5 FIGURE 25. TOP VIEW ICE LEVEL CONTROL ASSEMBLY PART NO. 32770 IMD 300-15 AND 32770-002 IMD 302–5 4 24 14 23 17 16 15 22 21 19 18 20 FIGURE 26. SIDE VIEW ICE LEVEL CONTROL ASSEMBLY PART NO.
PAGE 42
ICE LEVEL CONTROL ASSEMBLY PARTS LIST FOR PART NO 32770 IMD 300–15 AND 32770–002 IMD302–15 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO.
PAGE 43
2 1 21 8 20 24 FIGURE 27. TOP VIEW ICE LEVEL CONTROL ASSEMBLY IMD 300-30 AND IMD 600-30PART NO. 31494-001 (115V) PART NO. 31494-002 (208V/220V) 6 7 3 17 10 4 11 5 16 9 12 14 22 15 13 25 19 23 18 FIGURE 28. SIDE VIEW ICE LEVEL CONTROL ASSEMBLY IMD 300-30 AND IMD 600-30PART NO. 31494-001 (115V) PART NO.
PAGE 44
ICE LEVEL CONTROL ASSEMBLY PARTS LIST IMD300–30 AND IMD600–30 PART NUO 31494–001 (115V) PART NO. 31494–002 (208V/220V) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 * PART NO.
PAGE 45
1 2 20 3 19 5 9 6 7 8 10 11 12 13 11 10 11 12 14 11 11 15 14 13 11 FIGURE 29. TOP VIEW ICE LEVEL CONTROL ASSEMBLY IMD 600-90 PART NO. 31892 6 27 29 7 20 8 26 8 30 28 2 16 17 19 18 31 24 23 25 32 22 21 33 37 35 19 36 34 38 39 FIGURE 30. SIDE VIEW ICE LEVEL CONTROL ASSEMBLY IMD 600-90 PART NO.
PAGE 46
ICE LEVEL CONATROL ASSEMBLY PARTS LIST IMD 600–90 PART NO. 31892 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 * * PART NO.
PAGE 47
21 22 23 7 20 6 1 19 17 18 16 5 13 15 4 3 10 8 14 8 27 28 25 26 31 30 26 24 FIGURE 31.
PAGE 48
BIN AND FRONT END ASSEMBLY PARTS LIST IMD 300-15, IMD 300-30 AND 600-30 ITEM NO. 1 2 3 4 5 6 7 8 300-15 PART NO. 638032744 638031108 300-30 PART NO. 638031110-01 638031108 600-30 PART NO.
PAGE 49
21 22 28 12 11 20 19 10 9 18 8 14 15 5 7 4 17 3 16 13 1 2 6 25, 26 24, 27 23 FIGURE 32.
PAGE 50
BIN AND FRONT END ASSEMBLY IMD PARTS LIST 600-90 ITEM NO. 1 * * * 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PART NO.
PAGE 51
2 6 3 7 1 5 4 4 11 10 9 8 5 12 638085277 FIGURE 33. ELECTRICAL BOX ASSEMBLY PART NO. 32776 IMD 300–15 AND PART NO.
PAGE 52
ELECTRICAL BOX ASSEMBLY PARTS LIST, PART NO. 32776 IMD 300–15 AND PART NO. 32776-002 IMD 302-15 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 *13 *14 * * * PART NO. 638004402 638010018 638004791 638004792 638007030-02 638007051-06 638007303-04 638007352-01 638007903-01 638007904-01 638007948-01 638032794 638032795 638032781 638032844 638032797 638032798 638032820 DESCRIPTION Relay, Anti-Freeze, 115V Relay, Anti-Freeze, 220V 50HZ Switch, Toggle Indicator Plate Screw, No. 8 By 5/8-In. Long Screw, No. 10-32 By 3/8-In.
PAGE 53
8 9 11 22 1 24 25 18 17 15 16 5 7 2 3 4 12 14 23 19 15 638085277 20 6 FIGURE 34.
PAGE 54
ELECTRICAL BOX ASSEMBLY PARTS LIST IMD 300–30, IMD 600–30 AND IMD 600-90 (ALL VOLTAGES) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 * * * * * * * * * * * PART NO.
PAGE 55
4 1 5 2 3 7 8 9 10 11 12 9 FIGURE 35. COMPRESSOR ELECTRICAL BOX ASSEMBLY AND PARTS LIST IMD 300-30, 600-30 AND 601-30 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 638085277 PART NO. DESRIPTION 638007905-01 638007002-03 638007204-02 638036219-001 638090112 638090222 638090242 Receptacle, 6-Circuit Screw, No. 6-32 By 3/8-In. Long Nut, Keps, No.
PAGE 56
3 4 1 2 6 7 8 8 5 9 FIGURE 36. COMPRESSOR ELECTRICAL BOX ASSEMBLY AND PARTS LIST IMD 302-30 ITEM NO. 1 2 3 4 5 6 7 8 9 PART NO. 638007042-04 638007204-03 638036219-001 638090132 638049273 638007352-01 638036364-02 638007030-07 638090134 DESRIPTION Screw, No. 8-32 Nut, Keps, No. 8-32 Electrical Box Start Relay (302-30, 220V) Terminal Board Bushing Capacitor Bracket Screw, No. 8 By 3/8-In.
PAGE 57
4 5 3 6 7 1 2 8 9 10 FIGURE 37. COMPRESSOR ELECTRICAL BOX ASSEMBLY AND PARTS LIST IMD 602-30 ITEM NO. 1 2 3 4 5 6 7 8 9 10 638085277 PART NO. DESRIPTION 638007042-04 638007204-03 638007905-01 638036219-001 638090238 638007204-02 638007002-03 638036364-02 638007030-07 638090244 Screw, No. 8-32 Nut, Keps, No. 8-32 Receptacle, 6-Circuit Electrical Box Start Relay (602-30, 220V) Nut, Keps, No. 6-32 Screw, No. 6-32 Capacitor Bracket Screw, No. 8 By 3/8-In.
PAGE 58
3 1 4 2 5 7 6 6 4 FIGURE 38. COMPRESSOR ELECTRICAL BOX ASSEMBLY AND PARTS LIST IMD 600-90 AND IMD 601–90 ITEM NO. 1 2 3 4 5 6 7 PART NO. 638090633 638090222 638090242 638007352-01 638007030-07 638090224 638090244 638036364-02 638090223 638090243 DESRIPTION Electrical Box Start Relay (600-90, 115V) Start Relay (601-90, 208V) Bushing Screw, No. 8 By 3/8-In.
PAGE 59
FIGURE 39. COMPRESSOR ELECTRICAL BOX ASSEMBLY IMD 602-90 EXPLODED VIEW AND PARTS LIST ITEM NO. 1 2 3 4 5 6 7 8 9 638085277 PART NO. DESRIPTION 638007042–04 638007204–03 638049273 638007030–07 638090238 638090633 638007352–01 638090244 638036364–02 Screw, No.
PAGE 60
4 1 15 7 9 2 5 11 13 3 16 6 11 12 9 8 14 10 1 10 9 8 2 13 3 12 14 5 15 4 7 11 16 6 FIGURE 40.
PAGE 61
DISPENSE MECHANISM ASSEMBLY PARTS LIST IMD 300-15, IMD300-30, IMD 600-30 AND IMD 600-90 PARTS LIST ITEM NO. 1 2 3 3A 4 5 6 7 8 9 10 11 12 13 14 15 16 638085277 PART NO.
PAGE 62
COMPLETE GEAR MOTORS, INCLUDING SEALS & MOUNT, ARE AVAILABLE AS FOLLOWS: MODEL GEAR MOTOR P/N IMD 300 SERIES 638090050–002 IMD 301 SERIES 638090050–003 IMD 302 SERIES 638090050–005 IMD 600 SERIES 638090050 IMD 601 SERIES 638090050–004 IMD 602 SERIES 638090050–006 24 26 6 25 1 5 3 27 7 8 10 23 22 14 17 11 4 2 15 18 16 13 9 19 12 20 21 20 FIGURE 41.
PAGE 63
FIGURE 42.
PAGE 64
GEAR MOTOR ASSEMBLY PARTS LIST ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 * * * * * * * * * * * * * * * * * * * PART NO.
PAGE 65
WARRANTY IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and workmanship under normal use and service. For a copy of the warranty applicable to your Cornelius, Remcor or Wilshire product, in your country, please write, fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number, serial number and the date of purchase. IMI Cornelius Offices AUSTRALIA D P.O.
PAGE 66
IMI CORNELIUS INC.