User's Manual
Table Of Contents
- Corning
- ONE™ Wireless Platform
- User Manual
- Preface Material
- About This Manual
- Hardware
- Software Warranty
- Returns
- Limitations of Liabilities
- Reporting Defects
- Warnings and Admonishments
- Regulatory Compliance Information
- RF Safety
- CAUTION!
- Laser Safety
- Licensee Contact Information
- Additional Relevant Documents
- Table of Contents
- 1 Introduction
- Figure 1-1. Illustration of Precise Service Distribution over Selected Remote Areas
- Table 1-17. Ethernet Path Units
- Figure 1-2. Corning ONE Wireless Platform Basic Architecture
- Figure 1-3. Corning® ONE™ Solution RF Path Architecture
- Figure 1-4. Corning ONE™ Solution Ethernet Path Architecture
- Figure 1-6. Illustration of Service Group Distribution
- Figure 1-7. Single Service Group Configuration
- Figure 1-8. Example of Dual Service Group Configuration
- Figure 1-9. Example of Three Service Group Configuration
- Figure 1-10. Example of Tri-Service Group Configuration with Two HEUs
- Figure 1-11. Example 1 of FMM-to-FRM Service Distribution
- Figure 1-12. Example 2 of FMM-to-FRM Service Distribution
- 2 Unit Descriptions - RF Path
- Figure 2-1. RF Path with HEU and OIU Headend Components
- Figure 2-2. RF Path with IHU Headend Component
- Figure 2-3. Example of HEU with Installed Modules
- Figure 2-4. HCM Module
- Figure 2-5. ACM Module
- Figure 2-6. RIM Module
- Figure 2-7.FRM
- Figure 2-8. RIX Expander Module Interfaces
- Figure 2-9. Expander Termination Module
- Figure 2-10. PSM-AC Power Supply Module
- PSM-DC
- Figure 2-11. DC Power Supply Module
- Figure 2-12. OIU Front Panel with Installed Modules
- Figure 2-13. Optical Interface Module
- Figure 2-14.FMM
- Figure 2-15. OIX Expander Module Interfaces
- Figure 2-16. IHU Front Panel with Installed Modules
- Figure 2-17. RF Path Remote-end Components
- Figure 2-18. ICU Front Panel Interfaces and Modules
- Figure 2-19. ICU Rear Panel Interfaces and PSM Modules
- Figure 2-20. RAU Module Interfaces
- Figure 2-21. RAU LEDs
- Table 2-19. RAU Status LEDs Description
- Figure 2-22. RAU5 Interfaces
- 3 Unit Descriptions - Ethernet Path
- Figure 3-2. CEU Front Panel with Installed CEM Module
- Figure 3-3. CEU Rear Panel
- Figure 3-5. CEM LEDs
- Figure 3-6. GEM Interfaces
- Figure 3-7. GEM LED Description
- Figure 3-8. GEU Enclosure: Top (Left) and Open Underside (Right)
- 4 Installation Guidelines
- Figure 4-1. Example of Communication Rack Installation
- Types of Power Supplies
- 5 Appendix E: Specifications
- RF Parameters for FCM Solution
- Optical Specifications
- Standards and Approvals
- RF Path: Coverage Component Specifications
- Fiber Connectivity Module (FCM) Specifications
- 6 Appendix F: Ordering Information
- HEU and OIU Assemblies and Modules
- Remote Units
- SFP+ Modules
- Ethernet Path Units
- Hardware
- Cable Ordering Information
- Cable Configurations
Introduction
CMA-331-AEN
Page 17
1.3.1.2 Safety and Regulatory Approvals
The safety and regulatory specifications listed below are relevant to all Corning
®
ONE™ wireless platform devices.
Regulation/Standard
Category
Approval
Laser Safety
FDA/CE 21 CFR 1040.10 and 1040.11 except for deviations pursuant to laser notice no.
50 and IEC 60825-1
EMC
CE EN 301 489, EN55022, EN 61000
FCC 47 CFR Part 15, 22, 24, 27
Safety
UL 60950
IEC 60825-1:2007
IEC 60825-2:2010
CAN/CSA-C22.2 No.60950-1-03
Fire Safety UL 2043 (applicable for RAU5 only)
Table 1-2. Safety and Regulatory Approvals
1.3.2 Power Specifications
Note: This section provides the power specifications for the headend units and the RAU/RAU5 (including GEM). For MRU
specifications refer to MRU datasheet (CMA-422-AEN) and user manual (CMA-438-AEN). These can be downloaded from
Corning partner portal.
1.3.2.1 Power Input and Consumption
RF Head End Units
Power Input
Power Consumption for Full Chassis
HEU AC power source: 100 to 220 V AC
Chassis with 12 RIMs and two RIX: 200 W
DC power source: 48 V DC
OIU AC power source: 100 to 220 V AC
Chassis with 12 OIMs and two OIX: 300 W
DC power source: 48 V DC
IHU AC power source: 100 to 220 V AC
Fully Loaded chassis: 300 W
DC power source: 48 V DC
Table 1-3. RF Headend Units Power Consumption
RAU + Add-On Modules
Max. Power Consumption
Power Input Range
RAU (alone) 37 V; 35 W 35 – 57 V DC
RAU + GEM 37 V; 39 W
Table 1-4. RAU Power and Current Consumption for Main Power Input