User's Manual
Table Of Contents
- Corning
- ONE™ Wireless Platform
- User Manual
- Preface Material
- About This Manual
- Hardware
- Software Warranty
- Returns
- Limitations of Liabilities
- Reporting Defects
- Warnings and Admonishments
- Regulatory Compliance Information
- RF Safety
- CAUTION!
- Laser Safety
- Licensee Contact Information
- Additional Relevant Documents
- Table of Contents
- 1 Introduction
- Figure 1-1. Illustration of Precise Service Distribution over Selected Remote Areas
- Table 1-17. Ethernet Path Units
- Figure 1-2. Corning ONE Wireless Platform Basic Architecture
- Figure 1-3. Corning® ONE™ Solution RF Path Architecture
- Figure 1-4. Corning ONE™ Solution Ethernet Path Architecture
- Figure 1-6. Illustration of Service Group Distribution
- Figure 1-7. Single Service Group Configuration
- Figure 1-8. Example of Dual Service Group Configuration
- Figure 1-9. Example of Three Service Group Configuration
- Figure 1-10. Example of Tri-Service Group Configuration with Two HEUs
- Figure 1-11. Example 1 of FMM-to-FRM Service Distribution
- Figure 1-12. Example 2 of FMM-to-FRM Service Distribution
- 2 Unit Descriptions - RF Path
- Figure 2-1. RF Path with HEU and OIU Headend Components
- Figure 2-2. RF Path with IHU Headend Component
- Figure 2-3. Example of HEU with Installed Modules
- Figure 2-4. HCM Module
- Figure 2-5. ACM Module
- Figure 2-6. RIM Module
- Figure 2-7.FRM
- Figure 2-8. RIX Expander Module Interfaces
- Figure 2-9. Expander Termination Module
- Figure 2-10. PSM-AC Power Supply Module
- PSM-DC
- Figure 2-11. DC Power Supply Module
- Figure 2-12. OIU Front Panel with Installed Modules
- Figure 2-13. Optical Interface Module
- Figure 2-14.FMM
- Figure 2-15. OIX Expander Module Interfaces
- Figure 2-16. IHU Front Panel with Installed Modules
- Figure 2-17. RF Path Remote-end Components
- Figure 2-18. ICU Front Panel Interfaces and Modules
- Figure 2-19. ICU Rear Panel Interfaces and PSM Modules
- Figure 2-20. RAU Module Interfaces
- Figure 2-21. RAU LEDs
- Table 2-19. RAU Status LEDs Description
- Figure 2-22. RAU5 Interfaces
- 3 Unit Descriptions - Ethernet Path
- Figure 3-2. CEU Front Panel with Installed CEM Module
- Figure 3-3. CEU Rear Panel
- Figure 3-5. CEM LEDs
- Figure 3-6. GEM Interfaces
- Figure 3-7. GEM LED Description
- Figure 3-8. GEU Enclosure: Top (Left) and Open Underside (Right)
- 4 Installation Guidelines
- Figure 4-1. Example of Communication Rack Installation
- Types of Power Supplies
- 5 Appendix E: Specifications
- RF Parameters for FCM Solution
- Optical Specifications
- Standards and Approvals
- RF Path: Coverage Component Specifications
- Fiber Connectivity Module (FCM) Specifications
- 6 Appendix F: Ordering Information
- HEU and OIU Assemblies and Modules
- Remote Units
- SFP+ Modules
- Ethernet Path Units
- Hardware
- Cable Ordering Information
- Cable Configurations
Appendix E: Specifications
CMA-331-AEN
Page 73
Optical Specifications
OIM to Remotes
Optical Output Power < 9 dBo
Max. Optical Budget 5 dB
Back Reflectance - 60 dB
Optical Connector
OIM: Female MTP
®
connector;
RAU: Single Mode; LC APC Duplex
RAU5: LC APC SM
Fiber Type
Corning
®
SMF-28
®
fiber or compatible
Wavelength
1310 ± 10 nm (@ 25
◦
C)
FMM to FRM
Optical Output Power
< 14 dBm (over multiple wavelengths)
Optical Budget Single hop:
Low power remote: 10 dB (maximum)/12.4 mi
Low/mid-power remote: 5 dB
Note: See ordering information for selection of appropriate 10 GbE
SFP+ corresponding
to actual optical budget. Optical attenuator is included for 10 GbE for short distance links.
Second hop (future option): 5 dB/ 1.2 2 miles (for low-power solutions)
Maximum Optical Back Reflection
per Mated-pair Connectors
- 60 dB
Optical Connector
LC/APC SMF (Green) Simplex (for FMM-to-FRM link)
LC/UPC SMF (Blue) Duplex (for connection to customer’s 10 GbE SFP+)
Fiber Type
Corning
®
SMF-28
®
or equivalent
Optical Return Loss (ORL)
ORL should be greater than 60 dB for all connections between the FMM and FRM. This
requires use of angled polished connectors (APC) exclusively
Dispersion Compensation
Links in excess of 7 km require the insertion of a dispersion compensating fiber (DCF).
See ordering information for selection of appropriate DCF module
Environmental Specifications
Operating Temperature
0°C to +50°C (32°F to 122°F)
Storage Temperature
-20°C to 85°C (-4°F to 185°F)