User's Manual
Table Of Contents
- Corning
- ONE™ Wireless Platform
- User Manual
- Preface Material
- About This Manual
- Hardware
- Software Warranty
- Returns
- Limitations of Liabilities
- Reporting Defects
- Warnings and Admonishments
- Regulatory Compliance Information
- RF Safety
- CAUTION!
- Laser Safety
- Licensee Contact Information
- Additional Relevant Documents
- Table of Contents
- 1 Introduction
- Figure 1-1. Illustration of Precise Service Distribution over Selected Remote Areas
- Table 1-17. Ethernet Path Units
- Figure 1-2. Corning ONE Wireless Platform Basic Architecture
- Figure 1-3. Corning® ONE™ Solution RF Path Architecture
- Figure 1-4. Corning ONE™ Solution Ethernet Path Architecture
- Figure 1-6. Illustration of Service Group Distribution
- Figure 1-7. Single Service Group Configuration
- Figure 1-8. Example of Dual Service Group Configuration
- Figure 1-9. Example of Three Service Group Configuration
- Figure 1-10. Example of Tri-Service Group Configuration with Two HEUs
- Figure 1-11. Example 1 of FMM-to-FRM Service Distribution
- Figure 1-12. Example 2 of FMM-to-FRM Service Distribution
- 2 Unit Descriptions - RF Path
- Figure 2-1. RF Path with HEU and OIU Headend Components
- Figure 2-2. RF Path with IHU Headend Component
- Figure 2-3. Example of HEU with Installed Modules
- Figure 2-4. HCM Module
- Figure 2-5. ACM Module
- Figure 2-6. RIM Module
- Figure 2-7.FRM
- Figure 2-8. RIX Expander Module Interfaces
- Figure 2-9. Expander Termination Module
- Figure 2-10. PSM-AC Power Supply Module
- PSM-DC
- Figure 2-11. DC Power Supply Module
- Figure 2-12. OIU Front Panel with Installed Modules
- Figure 2-13. Optical Interface Module
- Figure 2-14.FMM
- Figure 2-15. OIX Expander Module Interfaces
- Figure 2-16. IHU Front Panel with Installed Modules
- Figure 2-17. RF Path Remote-end Components
- Figure 2-18. ICU Front Panel Interfaces and Modules
- Figure 2-19. ICU Rear Panel Interfaces and PSM Modules
- Figure 2-20. RAU Module Interfaces
- Figure 2-21. RAU LEDs
- Table 2-19. RAU Status LEDs Description
- Figure 2-22. RAU5 Interfaces
- 3 Unit Descriptions - Ethernet Path
- Figure 3-2. CEU Front Panel with Installed CEM Module
- Figure 3-3. CEU Rear Panel
- Figure 3-5. CEM LEDs
- Figure 3-6. GEM Interfaces
- Figure 3-7. GEM LED Description
- Figure 3-8. GEU Enclosure: Top (Left) and Open Underside (Right)
- 4 Installation Guidelines
- Figure 4-1. Example of Communication Rack Installation
- Types of Power Supplies
- 5 Appendix E: Specifications
- RF Parameters for FCM Solution
- Optical Specifications
- Standards and Approvals
- RF Path: Coverage Component Specifications
- Fiber Connectivity Module (FCM) Specifications
- 6 Appendix F: Ordering Information
- HEU and OIU Assemblies and Modules
- Remote Units
- SFP+ Modules
- Ethernet Path Units
- Hardware
- Cable Ordering Information
- Cable Configurations
Appendix E: Specifications
CMA-331-AEN
Page 78
RF Path: Coverage Component
Specifications (continued)
Optical Interface Unit (OIU) (continued)
Physical
Characteristics
(Chassis +
Modules)
Mounting:
Rack-mount – 19 in and 4U
Dimensions
(
H x W x D):
Chassis: 7 x 17.3 x 18.95 in
(177.8 x 440 x 481.7 mm)
Cable Management
Tray:
6.96 x 20.02 x 4.35 in
(176.9 x 508.6 x 110.6 mm)
Weight
: Chassis :
Per OIM:
Per OIX:
ACM:
PSM:
37 lbs (16.8 kg)
1.5 lbs (0.7 kg)
1.54 lbs (0.7 kg)
2.2 lbs (1.0 kg)
1.98 lbs (0.9 kg)
Integrated Headend Unit (IHU)
IHU will host the following modules:
1. RIX - Radio Interface Expander; RF interface to OIX module
2. RIM - Radio Interface Module; RF source conditioner.
Up to eight (four in RIM slots [2-5] and four in combo slots [6-9]) RIMs can be
hosted by the IHU
3. OIM- Optical Interface Modules; converts the RF to three optical link
Up to eight (four in OIM slots [10-13] and four in combo slots [6-9])
4. OIX- Optical Interface Expander; OIU to IHU interface Module.
5. HCM- Headend Control Module; overall system management module
6. ACM – Auxiliary Control Module; provides interfaces for management of IHU
modules via HCM; installed in IHUs’ in configurations with more than one
headend unit (i.e. HEU/IHU)
7. PSM- Power Supply Module; AC or DC power supply; IHU Max Power
Consumption (Full Chassis): 300 W
6. ERFC – RF interface cable, 9-PIN; L= 34 in (routed in provided Cable
Management Tray)
Note: Refer to HEU specifications for descriptions of RIX, RIM, HCM /ACM and
PSM modules and refer to OIU specifications for descriptions of OIM and OIX
modules
Physical
Characteristics
(Chassis and
Modules)
Mounting: Rack-mount – 19 in , 4U
Dimensions (H x W X D): Chassis: 7 x 17.3 x 15.5 in
(177.8 x 440 x 394 mm)
Weight: Chassis:
30 lbs (14 kg)
Per RIM: 1.9 lbs (0.9 kg)
Per OIM: 1.5 lbs (0.7kg)
RIX: 1.54 lbs (0.7 kg
OIX: 1.54 lbs (0.7 kg)
ACM: 2.2 lbs (1.0 kg)
PSM: 1.98 lbs (0.9 kg)