User's Manual
Table Of Contents
- Corning
- ONE™ Wireless Platform
- User Manual
- Preface Material
- About This Manual
- Hardware
- Software Warranty
- Returns
- Limitations of Liabilities
- Reporting Defects
- Warnings and Admonishments
- Regulatory Compliance Information
- RF Safety
- CAUTION!
- Laser Safety
- Licensee Contact Information
- Additional Relevant Documents
- Table of Contents
- 1 Introduction
- Figure 1-1. Illustration of Precise Service Distribution over Selected Remote Areas
- Table 1-17. Ethernet Path Units
- Figure 1-2. Corning ONE Wireless Platform Basic Architecture
- Figure 1-3. Corning® ONE™ Solution RF Path Architecture
- Figure 1-4. Corning ONE™ Solution Ethernet Path Architecture
- Figure 1-6. Illustration of Service Group Distribution
- Figure 1-7. Single Service Group Configuration
- Figure 1-8. Example of Dual Service Group Configuration
- Figure 1-9. Example of Three Service Group Configuration
- Figure 1-10. Example of Tri-Service Group Configuration with Two HEUs
- Figure 1-11. Example 1 of FMM-to-FRM Service Distribution
- Figure 1-12. Example 2 of FMM-to-FRM Service Distribution
- 2 Unit Descriptions - RF Path
- Figure 2-1. RF Path with HEU and OIU Headend Components
- Figure 2-2. RF Path with IHU Headend Component
- Figure 2-3. Example of HEU with Installed Modules
- Figure 2-4. HCM Module
- Figure 2-5. ACM Module
- Figure 2-6. RIM Module
- Figure 2-7.FRM
- Figure 2-8. RIX Expander Module Interfaces
- Figure 2-9. Expander Termination Module
- Figure 2-10. PSM-AC Power Supply Module
- PSM-DC
- Figure 2-11. DC Power Supply Module
- Figure 2-12. OIU Front Panel with Installed Modules
- Figure 2-13. Optical Interface Module
- Figure 2-14.FMM
- Figure 2-15. OIX Expander Module Interfaces
- Figure 2-16. IHU Front Panel with Installed Modules
- Figure 2-17. RF Path Remote-end Components
- Figure 2-18. ICU Front Panel Interfaces and Modules
- Figure 2-19. ICU Rear Panel Interfaces and PSM Modules
- Figure 2-20. RAU Module Interfaces
- Figure 2-21. RAU LEDs
- Table 2-19. RAU Status LEDs Description
- Figure 2-22. RAU5 Interfaces
- 3 Unit Descriptions - Ethernet Path
- Figure 3-2. CEU Front Panel with Installed CEM Module
- Figure 3-3. CEU Rear Panel
- Figure 3-5. CEM LEDs
- Figure 3-6. GEM Interfaces
- Figure 3-7. GEM LED Description
- Figure 3-8. GEU Enclosure: Top (Left) and Open Underside (Right)
- 4 Installation Guidelines
- Figure 4-1. Example of Communication Rack Installation
- Types of Power Supplies
- 5 Appendix E: Specifications
- RF Parameters for FCM Solution
- Optical Specifications
- Standards and Approvals
- RF Path: Coverage Component Specifications
- Fiber Connectivity Module (FCM) Specifications
- 6 Appendix F: Ordering Information
- HEU and OIU Assemblies and Modules
- Remote Units
- SFP+ Modules
- Ethernet Path Units
- Hardware
- Cable Ordering Information
- Cable Configurations
Appendix E: Specifications
CMA-331-AEN
Page 82
RF Path: Coverage Component
Specifications (continued)
Cavity Duplexer for LTE 700 MHz
LTE 700 MHz external cavity duplexer for RAU modules supporting the LTE band and
which are deployed alongside units supporting the public safety service.
Frequency Range
777 MHz ~ 787 MHz
Bandwidth
10 MHz
Insertion Loss (Max.)
1.5 dB
Passband Ripple (Max.)
0.8 dB
Return Loss (Min.)
8.0 dB, all ports
Rejection
55 dB Min @ DC ~ 620 MHz
40 dB Min @ 698 MHz ~ 716 MHz
35 dB Min @ 728 MHz ~ 757 MHz
30 dB Min @ 765 MHz ~ 775 MHz
30dB Min @ 793 MHz ~ 1000 MHz
25 dB Min @ 1396 MHz ~ 1432 MHz
40 dB Min @ 1800 MHz ~ 2700 MHz
Average Power Rating
0.5 W CW Max.
In/Out Impedance
50 Ohms Nominal
Operating Temperature
-20
◦
C to +85
◦
C
Environmental
RoHS compliant