User's Manual
Table Of Contents
- 1. INTRODUCTION
- 2. RS232 SERIAL PROTOCOL PRESENTATION
- 3. setting internal waveport CF parameters
- 3.1 Configuring functional parameters
- 3.2 Wake-up and synchronization
- 3.3 Configuring control parameters
- 3.3.1 Selecting RF communication mode
- 3.3.2 Selecting radio channel when FHSS is deselected
- 3.3.3 Selecting radio board transmission power
- 3.3.4 Activating RSSI threshold auto-correction
- 3.3.5 Selecting the serial baud rate
- 3.3.6 Reading Waveport CF firmware version
- 3.3.7 Reading RSSI
- 3.3.8 RSSI command format
- 3.3.9 TEST Mode
- 4. SERVICE COMMANDS
- 5. COMMUNICATION MODES
Waveport CF user manuel Coronis Systems
Appendix III – Parameter setting commands
CMD Name Description
0x40 REQ_WRITE_RADIO_PARAM Request to update radio parameters
0x41 RES_WRITE_RADIO_PARAM Radio board response to radio parameter update
0x42 REQ_CHANGE_UART_BDRATE Request to update serial link baud rate
0x43
RES_CHANGE_UART_BAUDRA
TE
Radio board response to the serial link baud rate update. Serial link baud rate
is updated after has ended
0x44 REQ_CHANGE_TX_POWER
(1)
Request to update radio board transmission power
0x45 RES_CHANGE_TX_POWER
(1)
Radio board response to transmission power update
0x46
REQ_WRITE_AUTOCORR_STAT
E
Request to update WAVENIS RF ASIC RSSI threshold auto-correction state
0x47
RES_WRITE_AUTOCORR_STAT
E
Radio board response to WAVENIS RF ASIC auto-correction state update
0x50 REQ_READ_RADIO_PARAM Request to read radio parameters
0x51 RES_READ_RADIO_PARAM Radio board response to parameter reading request
0x54 REQ_READ_TX_POWER Request to read radio board transmission power
0x55 RES_READ_TX_POWER Radio board response to the transmission power reading
0x5A
REQ_READ_AUTOCORR_STAT
E
Request to read WAVENIS RF ASIC RSSI threshold auto-correction state
0x5B
RES_READ_AUTOCORR_STAT
E
Radio board response to WAVENIS RF ASIC auto-correction state reading.
0x60 REQ_SELECT_CHANNEL Request to select operating radio channel when FHSS is deselected
0x61 RES_SELECT_CHANNEL Response to channel selection request
0x62 REQ_READ_CHANNEL Request to read the operating radio channel when FHSS is deselected
0x63 RES_READ_CHANNEL Response to read channel request
0x64 REQ_SELECT_PHYCONFIG Request to select RF medium communication mode
0x65 RES_SELECT_PHYCONFIG Response to communication mode selection request
0x66 REQ_READ_PHYCONFIG Request to read RF medium communication mode
0x67 RES_READ_PHYCONFIG Response to communication mode read request
0x68 REQ_READ_REMOTE_RSSI Request to read RSSI level from remote module
0x69 RES_READ_REMOTE_RSSI Response to the read remote RSSI level request
0x6A REQ_READ_LOCAL_RSSI
Request to read the local Waveport CF RSSI level via an exchange with a
remote module
0x6B RES_READ_LOCAL_RSSI Response to the read local RSSI level request
0xA0 REQ_FIRMWARE_VERSION Request to read radio board firmware version
0xA1 RES_FIRMWARE_VERSION Radio board response to firmware version reading
0xB0 MODE_TEST Switch Waveport CF into a selected test mode
(1) : Commands available only on Waveport CF 25mW radio board
Compact_Flash-UserManual 67