Owners manual

ManualsBrandsCorsa Performance ManualsAutomotive14108CBBLK Sport Cat-Back Exhaust System Fits 09-13 Corvette

TOACTIVATEYOURLIMITEDLIFETIMEWARRANTYGOTO:

CORSAPERFORMANCE.COM/WARRANTY

ForFullColorInstallationInstructions,PleaseVisit:

CORSAPERFORMANCE.COMandSearchbyPartNumber

Please be sure to review the enclosed instructions prior to beginning the installation process.

If you have any questions about the enclosed parts, instructions or encounter a problem during

Installation: CALL CORSA PERFORMANCE TECHNICAL ASSISTANCE AT

800.486.0999

STOP

IMPORTANT WARRANTY &

INSTALLATION INSTRUCTIONS ATTACHED

Please Forward All Attached Information to Consumer

Warranty Not Valid Unless Returned to CORSA Exhaust

We ask that you take a few moments to complete our warranty registration form:



CORSAPERFORMANCEEXHAUSTl140BLAZEINDUSTRIALPKWY,BEREA,OHIO44017



Summary of content (12 pages)

PAGE 1
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to complete our warranty registration form: TO ACTIVATE YOUR LIMITED LIFETIME WARRANTY GO TO: CORSAPERFORMANCE.COM/WARRANTY STOP For Full-‐Color Installation Instructions, Please Visit: CORSAPERFORMANCE.
PAGE 2
PAGE 3
• • • • • 13 mm Socket 15 mm Socket 18 mm Socket 15 mm Open End Wrench Torque Wrench (20-100 ft.-lb.) Drive extensions for Ratchet (MINIMUM OF 17 INCHES) CORVETTE C6 Exhaust System Installation Ellation C6 • 2009+ Corvette C6 Technical Assistance: Recommended Tools: • • • • • (800) 486-0999 13 mm Socket Please be sure to review the attached instructions prior to beginning the installation process.
PAGE 4
Exhaust Removal: EXHAUST REMOVAL Your C6 must be raised high enough to remove the one-piece stock muffler and over-axle pipe assemblies. A safe vehicle hoist is strongly recommended for this task. NOTE: Be sure to save all nuts. These will be used to install your CORSA Performance exhaust system. 1. Using a 15 mm socket or wrench, remove the four front flange nuts (See Fig. A). 2. Using a 13 mm socket or wrench, remove the H-Pipe hanger nuts (See Fig. B). 3.
PAGE 5
9. Slide the rear muffler hangers out of the rubber isolators, using soapy water to aid in removal if needed. (See Fig. G). 10. Carefully slide the Driver side muffler out of the vehicle. 11. Carefully slide the Passenger side muffler out of the vehicle (See Fig. H). 12. Reinstall the stabilizer bar using the factory nuts and bolts. Tighten the bolts and nuts to factory specifications. 13. Slide axle pipes into factory H-Pipe BEFORE placing front flanges over studs. FIG. G FIG.
PAGE 6
CORSA Performance SPORT EXHAUST INSTALLATION: SPORT 1. Remove all exhaust system components from the shipping carton, including clamps. NOTE: There are two 2.5-inch clamps supplied. 2. Locate the Driver side (16CS4126) and Passenger side (16CS4113) axle pipes (See Fig. L & M). 3. Slide both Driver and Passenger axle pipes into position from the rear (See Fig. N). 4. Insert the axle pipes into the H-Pipe outlets and snug fit the clamps (See Fig. O).
PAGE 7
10. Repeat steps 6 to 9 above for the Driver side muffler (16CS2067 or 16CS2054). 11. Adjust the entire system as necessary to achieve the desired tips location and clearance to all driveline components. 12. Starting from the front of the vehicle, tighten all Torca clamps to 45 ft.-lb. 13. It is STRONGLY SUGGESTED that all clamps and fasteners be checked and re-tightened (if necessary) after a road test. Make sure the system has cooled prior to touching any exhaust components.
PAGE 8
SPORT & XTREME Driver Side Side Passenger Side Driver Over-the-Axle Pipe Pipe Over-the-Axle Over-the-Axle Pipe (16CS4126) HARDWARE KIT: (16CS4113) (16CS4003) (16CS4002) 2009 Corvette C6 PN 14108 PN 14470 PN 14959 (2) 2.5” Clamps (1) Package of Anti-Seize (16CS7024) + Muffler Assembly Muffler Assembly Options QUAD XTREME Twin 3.5” Pro-Series Tips Passenger Side PN 14470 Muffler Assembly (16CS2001) QUAD SPORT Twin 3.
PAGE 9
IMPORTANT WARRANTY & INSTALLATION INSTRUCTIONS ATTACHED Please Forward All Attached Information to Consumer. Warranty Not Valid Unless Returned to CORSA Exhaust We ask that you take a few moments to Complete our warranty registration form. To Activate Your 10 Year LIMITED WARRANTY, Go To: CORSAPERFORMANCE.COM/WARRANTY MADE IN THE USA For Full-Color Installation Instructions, Please Visit: CORSAPERFORMANCE.
PAGE 10
PAGE 11
CORVETTE C6 X-PIPE Exhaust System Installation Corvette C6 X-Style Crossover Pipe (2005 & Up) PN 14163, 14127 & 14330 • • Tools Needed: 13 mm Socket 15 mm Socket • • Torque Wrench (20-100 ft.-lb.) Safety Glasses All Torca clamps should be tightened using a properly calibrated Torque Wrench. Using an air impact gun will damage the clamp and reduce its ability to effectively seal the joint. It may also cause the joint to separate thereby causing damage to your exhaust system and your vehicle.
PAGE 12
CORSA Performance X-PIPE KIT INSTALLATION: 1. Remove all X-pipe Kit components from the shipping carton. NOTE: There are two 2.5-inch clamps supplied. 2. Locate the X-pipe assembly, 16CS4013 OR 16CS4112, (See Fig. E) and the two Torca clamps. 3. Snug fit the clamps onto the outlets of the X-pipe assembly. The clamps should be pointing towards the center of the vehicle. 4. Using a 13 mm socket or wrench, install the X-Pipe hanger nuts. Tighten to factory specifications (See Fig. F). 5.