CARBIDE SERIES 100R SILENT EDITION Congratulation. Climatic 5. 200mm BBl Lo ey ASTRINGENT Removing the side panels.. installing the motherboard. installing Installing the PS. Ra moving the front R e stalling an ODD . el Maximum CPU cooler height: sy LS Tantalizing 550 and H Dds: 12 Installing » second front PRy FSY LNG 2H0mm Powering the oases fans. Installing the front [/O connector: Frequently asked questions: Thank you for purchasing the Carbide Series 100R Silent Edition Mid-Tower PC Case.
CARBIDE SERIES 100R SILENT EDITION Accessory Kit Contents a2 -D Cable tiles MBD/HDD craws S5D/0DD craws 55D pan head Short fan screws Long fan screws screws x18 x4 © 1/0 Pansy (x2 USB 3.0, Headphones/ Mic, and Po war/ Resat) ) Removable front fascia 0 x2 Tool-fees removable ODD covers © solid side panel © Solid side panel ) x4 Tool-free 3.5” overdrive trays with 2.5" compatibility O 3-pin 120mm Fan ) Bottom PSU dust filter @) PEE screw rail € x4 Tool-free 3.5” hard drive cages with 2.
CARBIDE SERIES 100R SILENT EDITION 3. Installing Card(s) Simply remove the thumbscrews then slide the side panels back and out. Remove thumbscrews and corresponding ot cover(s), Install the add-on card and precise with thumbscrews, Note: Cars sir recommends removing bath side panels and swotting them aside when bulling your system to avoid accidental demure. Both side panels are interchangeable and should b removed to reduce sutler. Installing the Motherboard 4.
CARBIDE SERIES 100R SILENT EDITION 5. Removing the Front Fascia 7. Installing BSDs and H Dds To remove the front fascia The Tour included drive (rot panel), grasp the tab trays support both 3.5° located at the bottom fascia and 2.5" devices. and pull outward. To install a 35" HDD, pull the drive tray from each side to extend the mounting points, Next, place your HDD note the tray and push the drive back to a close. No scows are. necessary to secure the drive onto the tray.
CARBIDE SERIES 100R SILENT EDITION 9. Powering the Case Fans Frequently Asked Questions 1 Connect the DATA power 1. How do | remove the |/O Panel? connector to the BSU DATA knead, you can uninstall our 1/0 panel by removing the front power cable. gavels (step 5) than Unscrewing the 2 screws at each side of 2. Connect the 3 or 4-Pin fan pang. (seq drawing connector to tha case fan header. % Push the fan speed selector button on yer case toggle fan sporadic. H 2.
CAR BIDE SÉRIES 100R LISENT ÉDITION Installation de disques SSD et de lecteurs de disques durs Pour retirer la façade Les quatre plateaux (panneau avant), inclus prennent en charge tirez sur |a languette située indifféremment les disques an bas de la façade. 350025 pouces. Pour Installer un disque dur 3.5 po, tirez sur les deux cotés du plateau pour agrandir les points de montage. Ensuite, placez lo disque dur dans e plateau et repousses le dissous. pour fermer.
CABILDEAR SERIES 100R SILENTE EDITEN 5. Como remover la afascala frontal Para remover la fascina frontal (pande frontal), tome la pestaña localizada al fondo de. 1a fascina y tire hacia afuera. 6. Como Instalar una ODD (Unidad de disco épico) Primar, renueva fa cubierta del receptáculo de la unidad del panel frontal de 5957y después deslice la ODD an la Halla de la unidad hasta que el Seguro encaje, asegurando la unidad: Para liberar tna unidad óptica, presiona In pes tafia v tire Ta Unidad hacia afuera; 7.
