GAS RANGE COS-965AGC COS-965AGFC 36-IN FREESTANDING RANGE INSTALLATION MANUAL IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. INSTALLER: PLEASE LEAVE THIS GUIDE WITH THE HOMEOWNER. HOMEOWNER: PLEASE KEEP THIS GUIDE FOR FUTURE REFERENCE. Rev.22.
THANK YOU FOR YOUR PURCHASE Thank you for your purchase. We know that you have many brands and products to choose from and we are honored to know that you have decided to take one of our products into your home and hope that you enjoy it. COSMO Appliances are designed according to the strictest safety and performance standard for the North American market. We follow the most advanced manufacturing philosophy. Each appliance leaves the factory after thorough quality inspection and testing.
TABLE OF CONTENTS RANGE SAFETY ................................................................................................. 3 Anti-tip Device ........................................................................................................... 4 INSTALLATION REQUIREMENTS ...................................................................... 6 Tools and Parts .......................................................................................................... 6 Location Requirements .........
RANGE SAFETY WARNING Fire Hazard If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. - WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch. • Do not use any phone in your building. • Clear the room, building, or area of all occupants.
WARNING Tip Over Hazard • A child or adult can tip the range and be killed. • Install anti-tip bracket to floor or wall per installation instructions. • Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. • Re-engage the anti-tip bracket if range is moved. • Do not operate the range without anti-tip bracket installed and engaged. • Failure to follow these instructions can result in death or serious burns to children and adults.
Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER," "WARNING" or "CAUTION.
INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools Needed • 3/16" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors) • Tape measure • Flat-blade screwdriver • Phillips screwdriver • Noncorrosive leak-detection solution • Level • Drill • Wrench or pliers • Pipe wrench For Propane/Natural Gas Conversions • 15/16" (2.4 cm) combination wrench • 1/2" (1.
Parts Needed Gas supply line kit (supply line and 2 adapters) Optional Parts To purchase these or any other accessories, please visit www.cosmoappliances.com or reference the contact information at the end of this manual.
LOCATION REQUIREMENTS IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air. • It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the oven door on the oven frame. Rating Plate • The range should be located for convenient use in the kitchen. • Recessed installations must provide complete enclosure of the sides and rear of the range.
Mobile Home - Additional Installation Requirements • The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.
PRODUCT DIMENSIONS This manual covers several models. Your model may appear different from the models depicted. Dimensions given are maximum dimensions across all models. COS-965AGC 35.4 in (900 mm) 1.77 in (45 mm) Vent height 35.4 in (900 mm) To cooktop 25.0 in (635 mm) 27.0 in (686 mm) With handle 42.3 in (1075 mm) Door fully open COS-965AGFC 35.4 in (900 mm) 1.77 in (45 mm) Vent height 35.4 in (900 mm) To cooktop 25.0 in (635 mm) 27.0 in (686 mm) With handle 42.
CLEARANCES IMPORTANT: Some cabinet and building materials are not designed to withstand the heat produced by the oven for baking and self-cleaning. Check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. GIVEN DIMENSIONS ARE MINIMUM CLEARANCES. 35.6 in (90.5 cm) 18 in (45.7 cm) 36 in (91.4 cm) 6 in (15.2 cm) to left wall 30 in (76.2 cm) 6 in (15.2 cm) to right wall 13 in (33 cm) Maximum Overhead Cabinet Depth 25 in (63.
Power Supply Location IMPORTANT: An electrical outlet in the floor, may be either recessed or surface mounted, but an electrical outlet in the wall must be recessed to make the connection. For Direct Wiring, the electrical box should be mounted to the wall. a d e b g c h f a b c d e f g 30" (76 cm) h Recommended Location for Gas Supply Connection 11½" (29.2 cm) 6" (15.2 cm) 7¼" (18.4 cm) 3" (7.
Makeup Air Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. ELECTRICAL REQUIREMENTS WARNING Electrical Shock Hazard Electrically ground range. Failure to do so can result in death, fire or electrical shock.
ELECTRICAL REQUIREMENTS - U.S.A. ONLY Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA No. 70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169 Electrical Connection • Check local codes and consult gas supplier. Check existing electrical supply and gas supply.
ELECTRICAL REQUIREMENTS - CANADA ONLY Be sure that the electrical connection and wire size are adequate and in conformance with the CSA Standard C22.1, Canadian Electrical Code, Part 1 latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: Canadian Standards Association 178 Rexdale Blvd. Toronto, ON M9W 1R3 CANADA Electrical Connection Check local codes and consult gas supplier. Check existing electrical supply and gas supply.
GAS SUPPLY REQUIREMENTS WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. Examples of a qualified person include: • licensed heating personnel • authorized gas company personnel • authorized service personnel Failure to do so can result in death, explosion or fire.
LP Gas Conversion: Conversion must be performed by a qualified service technician. The qualified agency performing this work assumes the gas conversion responsibility. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See "GAS CONVERSION" section. GAS SUPPLY LINE Provide a gas supply line of 3/4" (1.9 cm) rigid pipe to the range location.
Gas shutoff valve: A manual gas line shut-off valve must be installed in an easily accessible location. Do not block access to shut-off valve. The valve is for turning on or shutting off gas to the range. a b c a Gas Supply Line b Shutoff Valve "Open" Position c To Range GAS PRESSURE REGULATOR The gas pressure regulator supplied with this range must be used.
INSTALLATION INSTRUCTIONS IMPORTANT: This appliance shall be installed only by authorized persons and in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, local water supply regulations. UNPACK RANGE WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. 1. Remove shipping materials, tape and film from the range.
INSTALL ANTI-TIP DEVICE WARNING Tip Over Hazard • A child or adult can tip the range and be killed. • Install anti-tip bracket to floor or wall per installation instructions. • Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. • Re-engage the anti-tip bracket if range is moved. • Do not operate the range without anti-tip bracket installed and engaged. • Failure to follow these instructions can result in death or serious burns to children and adults.
2. Place the bracket so that the back of the bracket is against the rear wall and the side edge of the bracket is 3/8" to 1/2" from the adjacent cabinet. NOTE: If there is no adjacent cabinet, place the bracket so that the edge of the bracket is 3/8" to 1/2" in from the range side panel. If the countertop overhangs the cabinet, offset the bracket from the cabinet by the depth of the overhang plus an additional 3/8" to 1/2". 3.
5. Install the anti-tip bracket. Wood • Using the two screws (provided) fasten the anti-tip bracket to the floor or wall. NOTE: The screw must enter wood or metal. Concrete • Insert the sleeve anchor into the drilled holes and then insert the lag bolts through the anti-tip bracket and into the floor or wall. The bolts must be properly tightened as recommended for the hardware. INSTALL ANTI-TIP CHAIN (COS-965AGFC ONLY) 1. Remove the anti-tip wall anchor hooks and screws from the parts bag. 2.
INSTALL BACKSPLASH • Install the backsplash to rear of range with the screws provided. GAS CONNECTION WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column.
This appliance shall be installed only by authorized persons and in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, local water supply regulations. This range is factory-set for use with Natural gas. To use this range with Propane gas, see the "GAS CONVERSION section before connecting this range to the gas supply.
1. Apply pipe-joint compound made for use with LP gas to all pipe thread connections. 2. Using a pipe wrench to tighten, connect the gas supply to the range. a b c d a b c d Gas Line from Range Washer (provided) Adapter (provided) Gas Pressure Regulator (provided) CONVERT TO LP GAS (OPTIONAL) This range is shipped from the factory set up to use natural gas. It can be converted to use LP gas by a qualified service technician. The LP conversion kit is sold separately.
COMPLETE CONNECTION WARNING Electrical Shock Hazard Disconnect power before servicing. Plug into a grounded 3-prong outlet. Do not use an adapter or an extension cord. Failure to do so can result in death, fire, or electrical shock 1. Open the manual shutoff valve in the gas supply line. The valve is open when the handle is parallel to the gas pipe. 2. Test all connections by brushing on an approved noncorrosive leakdetection solution. If bubbles appear, a leak is indicated. Correct any leak found. 3.
Note: Align notches in burner caps with pins in burner base. Burner caps should be level when properly positioned. If burner caps are not properly positioned, surface burners will not light. Cap Incorrectly Positioned Base Auxiliary Burner Semi Rapid Burner Rapid Burner Correctly Positioned Triple Ring Burner 4. Place burner grates over burners and caps. 5. Plug in range or reconnect power. ADJUST FLAME HEIGHT Check and adjust the height of top burner flames.
The flame can be adjusted using the adjustment screw in the center of the valve stem. The valve stem is located directly behind the control knob. 1. Light the burner and turn the knob to the lowest setting (MIN). 2. Pull and remove the control knob. 3. Insert a small, flat-blade screwdriver into the adjustment screw, and slowly turn the screw until the flame appearance is correct. • Open the valve more if the flames are too small or fluttered. • Close the valve more if the flames are too large.
LEVEL RANGE IMPORTANT: Do not operate the range if its rear foot is not completely engaged in the anti-tip bracket. Never completely remove the leveling legs or the range will not be secured to the anti-tip device properly. 1. Slide range into final location, making sure rear leveling leg slides into the anti- tip bracket. Leave a 1" (2.5 cm) gap between the back of the range and the back wall. 2. Check that the range is level by placing a level on the oven bottom.
2. Slowly attempt to tilt the range forward. • If you encounter immediate resistance, the range foot is engaged in the anti-tip bracket. Range installation is completed. • If the rear of the range lifts more than 1/2" (1.3 cm) off the floor without resistance, stop tilting the range and lower it gently back to the floor. The range foot is not engaged in the anti-tip bracket. Proceed to Steps 3 and 4.
GAS CONVERSION WARNING Explosion Hazard Use a new CSA International approved gas supply line. Install a shut-off valve. Securely tighten all gas connections. If connected to LP, have a qualified person make sure gas pressure does not exceed 14" (36 cm) water column. Examples of a qualified person include: • licensed heating personnel • authorized gas company personnel • authorized service personnel Failure to do so can result in death, explosion or fire.
LP/PROPANE GAS CONVERSION IMPORTANT: Gas conversions must be done by a qualified service technician in accordance with the manufacturer's instructions and all codes and requirements of the authority having jurisdiction. The qualified agency performing this work assumes the gas conversion responsibility. Convert Gas Pressure Regulator 1. Turn manual shutoff valve to the closed position. 2. Unplug range or disconnect power. 3. Locate the gas pressure regulator on the back of the range.
7. Screw and tighten the regulator cap back into the gas pressure regulator with the wrench. Regulator Cap Convert Surface Burners 1. If installed, remove the burner grates. 2. Remove the burner grates, burner caps, and the burner base. 3. Remove the natural gas orifices with a 9/32" (7 mm) nut driver. Orifice 4. Replace the natural gas orifices with the correct LP gas orifices from the LP conversion kits. LP gas orifices are stamped with a size.
Orifice Chart for Surface and Oven Burners: COS-965AGC / COS-965AGFC Burner Placement Rapid Front Left Auxiliary Front Right Triple Ring Center Semi Rapid Rear Left Semi Rapid Rear Right Broil Oven Top Bake Oven Bottom Orifice Type Orifice Size (mm) NG LP NG LP NG LP NG LP NG LP NG LP NG LP 1.45 0.91 1.05 0.70 2.10 1.22 1.29 0.80 1.29 0.80 1.15 0.71 1.85 1.10 Burner Rating 8,800 BTU 5,000 BTU 18,000 BTU 17,000 BTU 6,900 BTU 6,900 BTU 5,800 BTU 14,000 BTU A. Rapid (Large) B.
Convert Oven Bake Burner 1. Remove Bake Burner Cover Open your oven door and unscrew the back two screws of bake burner cover. Remove the bake burner cover. 2. Remove Flame Spread Plate Unscrew the four screws of the flame spread plate. Remove the flame spread plate. 3. Slide Out Burner Unscrew the front two screws holding the burner in place. Slide out the burner up and towards oven door out of the socket, careful not to sever or pull on the wire. 4.
Convert Oven Broil Burner 1. Unscrew Front Bracket Locate the bracket at the front of the broiler. Remove the screw. 2. Remove the Burner Carefully slide the burner forward and out of the socket, without severing or damaging the wire attached. Carefully lay the burner down as shown in the image to the right. 3. Change the Burner Orifice With the burner out of the way look for the orifice as shown. Continue with changing the orifice. Complete Gas Conversion 1. Open shutoff valve in the gas supply line. 2.
IMPORTANT Do Not Return This Product To The Store If you have a problem with this product, please contact COSMO Customer Support at +1 (888) 784-3108 DATED PROOF OF PURCHASE, MODEL #, AND SERIAL # REQUIRED FOR WARRANTY SERVICE. IMPORTANT Ne pas Réexpédier ce Produit au Magasin Pour tout problème concernant ce produit, veuillez contacter le service des consommateurs Cosmo Customer Support au +1 (888) 784-3108 UNE PREUVE D’ACHAT DATEE EST REQUISE POUR BENEFICIER DE LA GARANTIE.
MEMO
APPLIANCES Cosmo is constantly making efforts to improve the quality and performance of our products, so we may make changes to our appliances without updating this manual. Electronic version of this manual is available at: www.cosmoappliances.