Instruction manual

30
8.1 - Removing of a
boiler from a
common venting
system
WARNING!!! DO NOT connect this
boiler or any other appliance using
a positive pressure, in a common
vent system! Failure to comply with
this WARNING could result in the
accumulation of carbon monoxide
gas which can cause severe
personal injury or death!
When an existing boiler is removed
from a common venting system, the
common venting system is likely to be
too large for proper venting of the
appliances remaining connected to it.
At the time of removal of an existing
boiler, the following steps shall be
followed with each appliance remaining
connected to the common venting
system placed in operation, while the
other appliances remaining connected
to the common venting system are not
in operation.
(a) Seal any unused openings in the
common venting system.
(b) Visually inspect the venting system
for proper size and horizontal pitch
and determine there is no blockage
or restriction, leakage, corrosion and
other deficiencies which could
cause an unsafe condition.
(c) Insofar as is practical, close all
building doors and windows and all
doors between the space in which
the appliances remaining connected
to the common venting system are
located and other spaces of the
building. Turn on clothes dryers and
any appliance not connected to the
common venting system. Turn on
any exhaust fans, such as range
hoods and bathroom exhausts, so
they will operate at maximum
speed. Do not operate a summer
exhaust fan. Close fireplace
dampers.
(d) Place in operation the appliance
being inspected. Follow the lighting
instructions. Adjust thermostat so
appliance will operate continuously.
(e) Test for spillage at the draft hood
relief opening after 5 minutes of
main burner operation. Use the
flame of a match or candle, or
smoke from a cigarette, cigar or
pipe.
(f) Alter it has been determined that
each appliance remaining connected
to the common venting system
properly vents when tested as
outlined above, return doors,
windows, exhaust fans, fireplace
dampers and any other gas-burning
appliance to their previous condition
of use.
(g) Any improper operation of the
common venting system should be
corrected so the installation
conforms with the National Fuel Gas
Code, ANSI Z223.1 /NFPA 54 and/or
CAN/CSA B149.1, Natural Gas and
Propane Instal-lation Code. When
resizing any portion of the common
venting system, the common venting
system should be resized to
approach the minimum size as
determined using the appropriate
tables in Part 11 of the National Fuel
Gas Code, ANSI Z223.1 /NFPA 54
and/or CAN/CSA B149. 1, Natural
Gas and Propane Installation Code.
Au moment du retrait d’une chaudière
existante, les mesures suivantes
doivent être prises pour chaque
appareil toujours raccordé au système
d’évacuation commun et qui fonctionne
alors que d’autres appareils toujours
raccordés au système d’évacuation ne
fonctionnent pas: système
d’évacuation
(a) Sceller toutes les ouvertures non
utilisées du système d’évacuation.
(b) Inspecter de façon visuelle le
système d’évacuation pour déter-
miner la grosser et l’inclinaison
horizontale qui conviennent et
s’assurer que le système est
exempt d’obstruction, d’étrangle-
ment de fruite, de corrosion et
autres défaillances qui pourraient
présenter des risques.
8 - INSTALLATION - Vent & combustion air
(c) Dans la mesure du possible, fermer
toutes les portes et les fenêtres du
bâtiment et toutes les portes entre
l’espace où les appareils toujours
raccordés du système d’évacuation
sont installés et les autres espaces
du bâtiment. Mettre en marche les
sécheuses, tous les appareils non
raccordés au système d’évacuation
commun et tous les ventilateurs
d’extraction comme les hottes de
cuisinère et les ventilateurs des
salles de bain. S’assurer que ces
ventilateurs fonctionnent à la vitesse
maximale. Ne pas faire fonctionner
les ventilateurs d’été. Fermer les
registres des cheminées.
(d) Mettre l’appareil inspecté en
marche. Suivre les instructions
d’allumage. Régler le thermostat de
façon que l’appareil fonctionne de
façon continue.
(e) Faire fonctionner le brûleur principal
pendant 5 min ensuite, déterminer si
le coupe-tirage déborde à l’ouverture
de décharge. Utiliser la flamme
d’une allunette ou d’une chandelle
ou la fumée d’une cigarette, d’un
cigare ou d’une pipe.
(f) Une fois qu’il a été déterminé, selon
la métode indiquée ci-dessus, que
chaque appareil raccordé au
système d’évacuation est mis à l’air
libre de façor adéquate. Remettre
les portes et les fenêtres, les
ventilateurs, les registres de
cheminées et les appareils au gaz à
leur position originale.
(g) Tout mauvais fonctionnement du
systéme d’évacution commun
devrait étré corrigé de façon que
l’installation soit conforme au
National Fuel Gas Code, ANSI
Z223.1/NFPA 54 et (ou) aux codes
d’installation CSA-B149. Si la
grosseur d’une section du système
d’ évacuation doit étré modifiée, le
système devrait étré modifié pour
respecter les valeurs minimales des
tableaux pertinents de l’appendice F
du National Fuel Gas Code, ANSI
Z223.1/ NFPA 54 et (ou) des codes
d’installation CSA-B149.