CR-16A User Guide

REMOTE CONTROL CR-16A
OVP
INV
PWR.
SAV.
GRID
UVP OLP OTP
20
40
60
80
100
Low
Norm.
High
BATTERY
VOLTAGE POWER (%)
OUTPUT
REMOTE CONTROL CR-16B
FLOAT
ABSORPTION
BULK
OVP
INV
PWR.
SAV.
GRID
UVP OLP OTP
CHG
20
40
60
80
100
Low
Norm.
High
BATTERY
VOLTAGE POWER (%)
OUTPUT
33
55
2
11
44
89
76
Ø4.5
77
10.5
6.5 72
JP1
8
Aux port
AUX
6
7
Phone Jack
Connector
!
A
6
1
B
6
1
9.6±0.2
9.6±0.2
12.4±0.3
6.5±0.2
14.6±0.3
3.1±0.2
12.4±0.3
6.5±0.2
14.6±0.3
3.1±0.2
A
6
5
4
3
2
1
WIRE COLOR
YELLOW
BLUE
GREEN
WHITE
BLACK
RED
B
6
5
4
3
2
1
User Guide For CR-16 Remote Control
1. Features
• Battery bank voltage display
• Output power display
• Error condition indicator（High Battery, Low Battery, Over Temperature, Over Load conditions）
• Action condition indicator（INV, GRID, POWER SAVING, CHARGING STATUS）
• Connection failure notification
2. Specification
• Input Voltage：10.5 ~ 66 Vdc
• Operating Temperature Range：0 ~ 40 ℃
• Storage Temperature Range：- 30 ℃ ~ 70 ℃
• Stand-By Current Draw：< 80mA
• Applicable Models：CR-16A – SP Series
CR-16B – SC & SL Series
Note：Grid LED is only functional when connecting SP series with TR-40.
3. Introduction
3-1. Front Panel Introduction
Figure 1. CR-16 Front Panel Introduction
Power ON/OFF Button：
Power ON/OFF button is to turn the inverter on or off.
Charging Status LED (BULK / ABSORPTION / FLOAT) shows the charging status：(Only
applicable to SL series)
• BULK：When the battery is in low voltage status, the battery is charged at constant current by
maximum charge current.
• ABSORPTION：When the battery is near fully charged, the battery keeps charging by constant
voltage mode.
3-2. Rear Panel Introduction
Figure 2. CR-16 Rear Panel Introduction (Unit: mm [inch]) Figure 3. Aux Connector (Unit: mm [inch])
Aux port：
The connector (Fig.3) connected to AUX wire (AWG 14 or 16) must connected with 12V / 0.5A
fuse.
• Ignition Lockout function – The ignition lockout function is to turn OFF the Inverter when the
auxiliary input wiring is connected to the ACC with 12 Volts.
• Return Override Function – The Return Override Function is to turn ON the inverter when the
auxiliary input wiring is connected to the reversed gear shift with 12 Volts.
Phone Jack Connector：
1. Before connection, please make sure to switch the inverter to REMOTE mode. (For SP series)
(Fig.4)
Figure 4. SP series remote position
2. Connect the RJ-11 cable between CR-16 remote and the inverter.
Figure 5. Phone Jack Connector (Unit: mm [inch])
WARNING!
DO NOT use standard telephone cable.
JP1：The JP1 is to set either Return Override Function or Ignition lockout function.
• JP1 jumper “Short” - Return Override Function
Return Override Function – The Return Override Function is to turn ON the inverter when the
auxiliary input wiring is connected to the reversed gear shift with 12 Volts.
• JP1 jumper “Open” – Ignition Lockout Function
Ignition Lockout function – The ignition lockout function is to turn OFF the inverter when the
auxiliary input wiring is connected to the ACC with 12 Volts.
• The connector which is connected to AUX power must use with 12V / 0.5A fuse.
Note：default mode is Open.
• FLOAT：When the battery is fully charged, this state maintains the battery at 100% charge
without overcharging or damaging the battery.
Please refer to the detail information in SL series user manual accordingly.
Output power indicator：
Output power indicator shows the power draw from the power inverter by the load. Ideally, the
output power indicator should remain in the green & orange area of the bar chart.
If the output power indicator is up to the red area, the OLP LED will flash and the inverter will shut
down.
Battery voltage indicator：
Battery voltage indicator will move up and down as the battery voltage changes. Ideally, the
voltage should remain in the green area of the bar chart. If the voltage goes into the red area at
the top and bottom of the bar chart, inverter may shut down.
Other Indicators：
• OVP (Over voltage protection indicator)：
It indicates that the power inverter shuts down because its input voltage is above limit voltage.
• UVP (Under voltage protection indicator)：
The under voltage indicator is to indicate the inverter shut down due to under voltage protection.
• OLP (Overload protection indicator)：
The overload indicator is to indicate the inverter shut down due to short circuit or overload
protection.
• OTP (Over temperature protection indicator)：
The over temp indicator is to indicate the inverter shut down due to over temperature protection.
Once the inverter cools down, the indicator will turn off automatically.
• INV. indicator：
The INV. indicator is to indicate the inverter is ready.
• PWR. SAV. Indicator：Power saving functions are described below：
• GRID indicator：
The GRID indicator is to indicate the AC Grid is connected to inverter.
(For SP series：Only functional when connecting SP Series with TR-40)
• CHG indicator：
The CHG indicator is to indicate the battery charging status (Only applicable to SL series).
Power ON/OFF Button
Charging Status LED
Output power indicator
Battery voltage indicator
LED
Trigged signal
AUX
JP1
Inverter
Status
Open OFF
OFF
ON
ON
Open
Short
Short
0
1
0
1
Solid
Flashing
Off
Ready
Active
Inactive
ON
OFF
Meaning Inverter Output
Other Indicators
1
1
6
8
7
3
4
5
2
4
52
3
22±1.0
10±0.5
Ø4.5±0.3
No.33, Sec. 2, Renhe Rd., Daxi Dist., Taoyuan City 33548, Taiwan
Phone：[phone] FAX：[phone]
http：// www.cotek.com.tw
2016.07._A0
EN
1 2
3 4