COUNTRYMAN E2 EARSET
Thanks for choosing the Countryman E2 Earset microphone. We’re confident you’ll find it the finest, most natural sounding, and most unobtrusive earset microphone available. The E2 provides high-quality pickup and excellent isolation with an ultra-miniature condenser element positioned near the ear and a directional pattern tuned to pick up the natural sound of the wearer while rejecting ambient noise.
Contents Handling the E2 3 Connecting E2 Snap-On Cables 5 Custom Fitting the E2 6 Using Collar Clips 10 Back Port Cleaning Procedure 11 Specifications 12 Declarations 14 2
Handling the E2 While the E2 Earset is designed for durability, moisture-resistance and flexibility, it is a highprecision instrument and we do suggest some basic precautions to prevent damage or sonic degradation: • Always use the E2 with its cap in place. The end caps are critical to the sound quality and also protect the capsule from makeup, moisture, and debris. • When a protective cap is not in place, avoid touching the end of the capsule with fingers or obstructing the opening with foreign substances.
x Handling the E2 (cont.) The E2’s earpiece and boom are constructed of an exceptionally flexible material which can be easily shaped to the wearer’s needs. To prevent damage to your Earset: • Avoid bending it over sharp angles (such as the end of your fingernail) or around a tight radius (less than 1/2” diameter). • Avoid bending the booms within 1/2” of the capsule or the earpiece within 1/2” of the connector. • Use the side of your finger or other rounded object.
Connecting E2 Snap-On Cables The Earset cable is easy to remove and change, allowing you to swap transmitter types, switch colors, or replace damaged parts in the field. Exercise care in connecting and disconnecting the cable connector. • Always grasp the connectors near the outer ends of the rubber sleeves and pull the connectors straight apart. When connecting listen for a click. • The connectors do not unscrew—line up the marks on the connector overmold and pull straight out to disconnect.
Custom Fitting the E2 Head-worn mics provide isolation by keeping the element consistently near the mouth. The ideal placement is with the tip of the element in front of the ear, about 1/8” away from the face. Since every performer’s face is different, we’ve made it easy to custom fit the E2 Earset: 1. Curve the boom so that it will rest against your face when worn.
Custom Fitting the E2 (cont.) 2. Put the loop over the ear with the base behind the earlobe and the capsule toward the mouth.
Custom Fitting the E2 (cont.) 3. Tip the mic to point toward the mouth. The mic should be barely visible, resting about 1/8” from the face mid cheek or completely hidden by the hair.
Custom Fitting the E2 (cont.) 4. Always use the collar clip to reduce clothing and cable noise. Leave enough slack in the cable such that the user can turn his/her head to both sides without tugging on the clip. Use the windscreen outdoors.
Using Collar Clips The Earset comes with two collar clips: one black and one white. These clips prevent movement in the cable from dislodging the Earset and can reduce cable noise. They are specifically designed to match the diameter of your E2 cable. Gently pull the cable down into the opening to attach the clip. Gently pull the cable out to remove the clip. We recommend always using a collar clip with the E2. Use both attachment points as shown.
Back Port Cleaning Procedure This procedure is rarely necessary, but it may help if frequency response and directionality have deteriorated because the back ports on the element are contaminated with dust or makeup. Make sure your hands, the work area, the Earset’s boom and end cap are clean. Take a 6” - 8” piece of clean painter’s or gaffer’s tape and form it into a circle, sticky side out. Stick it down on the top of a table, near the edge. Do not use tapes that may leave adhesive on the mic.
Specifications Frequency Response: Operating Current: Operating Voltage: Weight: 20Hz to 20kHz 500uA 1 to 2 Volts 0.07oz (2g) The E2 Earset is available in two sensitivities to match a wide range of applications: Model E2W5 for general speaking Sensitivity: 3.0 mV/Pascal Equivalent Acoustic Noise: 34 dBA SPL Overload Sound Level: 130 dB SPL Supplied Accessories: Carrying case, black and white cable clips, wind screen, and protective cap. Model E2W6 for loud speaking and vocals Sensitivity: 1.
Gai -10 -20 -30 Typical Directional Lav Specifications (cont.
Declarations We, Countryman Associates Inc., declare under our sole responsibility that the following products: Earset Microphone models E2*, E6*, E6D*, E6ID*, WCE6D*, WCE6ID* To which this declaration relates are in compliance with the essential requirements of: 2004/108/EC EN 55103-1 EN 55103-2 2002/96/EC 2003/108/EC 2002/95/EC RoHS EMC WEEE RoHS When used as specified.
Countryman Associates, Inc. 195 Constitution Drive, Menlo Park, CA 94025 Phone: (800) 669-1422 or (650) 364-9988 Fax: (650) 364-2794 Email: sales@countryman.com Web: www.countryman.