COUNTRYMAN E6 DIRECTIONAL EARSET MICROPHONE
Thanks for choosing the Countryman E6 Directional Earset microphone. We’re confident you’ll find it the finest, most natural sounding, and most unobtrusive directional microphone available. The Earset directional mic provides high-quality pickup while rejecting noise, bleed from stage monitors, and feedback—it’s a world-class vocal mic with far better isolation than an omnidirectional mic can provide. The ultra-miniature condenser element is held close to the mouth by a thin boom and comfortable ear pad.
Contents Handling the E6 3 Connecting Snap-On Cables 5 Custom Fitting the E6 6 Using Directional Caps 12 Using Collar Clips 14 Back Port Cleaning Procedure 15 Specifications 16 Declarations 18 2
Handling the E6 While the E6 Directional is designed for durability, moisture-resistance and flexibility, it is a highprecision instrument and we do suggest some basic precautions to prevent damage or sonic degradation: • Always use the E6 with a cap in place. The end caps are critical to the sound quality and also protect the capsule from makeup, moisture, and debris.
Handling the E6 (cont.) The E6’s earpiece and boom are constructed of an exceptionally flexible material which can be easily shaped to the wearer’s needs. To prevent damage to your Earset: • Avoid bending it over sharp angles (such as the end of your fingernail) or around a tight radius (less than 1/2” diameter). • Avoid bending the booms within 1/2” of the capsule or the earpiece within 1/2” of the connector. • Use the side of your finger or other rounded object.
Connecting Snap-On Cables The Earset cable is easy to remove and change, allowing you to swap transmitter types, switch colors, or replace damaged parts in the field. Exercise care in connecting and disconnecting the cable connector. • Always grasp the connectors near the outer ends of the rubber sleeves and pull the connectors straight apart. When connecting listen for a click. • The connectors do not unscrew and normally rotate freely.
Custom Fitting the E6 Head-worn mics provide isolation by keeping the element near the mouth. The ideal placement is with the tip of the element at the corner of the mouth, about 1/4” away from the face. Since every performer’s face is different, we’ve made it easy to custom fit the E6 Directional Earset: 1. Try it on Pull the “C” shaped part of the earset open and clip it over your ear, so that the connector sits behind the earlobe and the boom goes over the top of your ear and runs along your face.
Custom Fitting the E6 (cont.) 2. Curve the Boom The Directional Earset is designed for a particular side (usually left). Curve the boom left if you intend to wear the earset on your right side; curve it to the right to wear it on your left side. Form the earpiece and overall shape with your fingertips. Make sure there is a short straight section between the boom and the earpiece—this sits in front of the ear, locking the Earset in place.
Custom Fitting the E6 (cont.) 3. Tighten the loop Gently twist the loop so that it is smaller than your ear, then allow it to return to its regular shape (this is less important with the E6i). The loop should now be smaller than it was before and there should be slight tension when the Earset is on your ear. The amount you tighten this loop makes a big difference in how stable and tight the earset feels.
Custom Fitting the E6 (cont.) 4. Spring the loop Holding the boom, gently pull the base of the Earset. When you clip the earset behind your ear, the connector will push out against your earlobe and the boom will press smoothly along your face. This is the fastest way to get a really tight fit if the Earset feels loose.
Custom Fitting the E6 (cont.) 5. Position the boom The Earset should now be firmly on your head, but the end of the microphone may be too high or too low, too far back or too far out in front of your mouth. Form the boom with your fingers until you get it comfortable and sounding good. The best spot is usually just back from the corner of your mouth when you are smiling. The boom should be very close to your face, or gently touching it, for most of its length.
Custom Fitting the E6 (cont.) • Placing the microphone too far forward can result in breath-related pops. Resist the urge to position the capsule directly in front of the mouth. x • Placing the microphone too far back will impact bass response and isolation. • The perfect position is with the mic within about a 1” spot at the corner of the mouth, about 1/4” away from the face and pointed slightly inward. • Curve the boom any way you like—the goal is to put the tip in the right place.
Using Directional Caps The C (cardioid) and H (hypercardioid) end caps modify your Earset’s directionality. The Earset should always have a protective cap in place to keep sweat, makeup and other foreign material out of the microphone. The hypercardioid cap provides the best isolation from all directions, with a null towards the floor where “wedge” monitors are often placed. The hypercardioid is slightly more sensitive to air movement and handling noise and should always be used with a windscreen.
Using Directional Caps (cont.) When removing and replacing the protective caps: • Grasp the microphone low on the boom, close to the capsule. • Hold the protective cap by the sides and pull straight off to remove. • To replace the protective cap, position the cap, hold the sides and press straight on firmly. • Never touch the sides or top of an uncapped mic element. Do not let your fingers slide across the element when removing the cap.
Using Collar Clips The Earset comes with two collar clips: one black and one white. These clips prevent movement in the cable from dislodging the Earset and can reduce cable noise. They are specifically designed to match the diameter of your E6 cable, either 1mm or 2mm. Gently pull the cable down into the opening to attach the clip. Gently pull the cable out to remove the clip. We recommend always using a collar clip with the Directional E6. Use both attachment points as shown.
Back Port Cleaning Procedure This procedure is rarely necessary, but it may help if frequency response and directionality have deteriorated because the back ports on the element are contaminated with dust or makeup. Make sure your hands, the work area, the Earset’s boom and end cap are clean. Take a 6” - 8” piece of clean painter’s or gaffer’s tape and form it into a circle, sticky side out. Stick it down on the top of a table, near the edge. Do not use tapes that may leave adhesive on the mic.
Specifications Frequency Response: 30Hz to 15kHz Operating Current: 400uA Operating Voltage: 1 to 2 Volts Power Supply Voltage: +3V with 2.7kOhm load +6V with 5.6kOhm load +9V with 15kOhm load Weight: 0.07oz (2g) Supplied Accessories: Carrying case, black and white cable clips, wind screen, and hypercardioid and cardioid caps. Detailed information on connecting Earsets to wireless transmitters can be found at: http://www.countryman.
Specifications (cont.) Frequency Response 1 kHz Polar Response 30° dB +10 0 -10 -20 20 0.
Declarations We, Countryman Associates Inc., declare under our sole responsibility that the following products: E6 / E6i Directional Earset Microphone models E6*, E6D*, E6ID*, WCE6D*, WCE6ID* To which this declaration relates are in compliance with the essential requirements of: 2004/108/EC EN 55103-1 EN 55103-2 2002/96/EC 2003/108/EC 2002/95/EC RoHS EMC WEEE RoHS When used as specified.
Countryman Associates, Inc. 195 Constitution Drive, Menlo Park, CA 94025 Phone: (800) 669-1422 or (650) 364-9988 Fax: (650) 364-2794 Email: sales@countryman.com Web: www.countryman.
